diff options
Diffstat (limited to 'conf.d/python.d/smartd_log.conf')
| -rw-r--r-- | conf.d/python.d/smartd_log.conf | 85 |
1 files changed, 85 insertions, 0 deletions
diff --git a/conf.d/python.d/smartd_log.conf b/conf.d/python.d/smartd_log.conf new file mode 100644 index 00000000..e16454df --- /dev/null +++ b/conf.d/python.d/smartd_log.conf @@ -0,0 +1,85 @@ +# netdata python.d.plugin configuration for smartd log +# +# This file is in YaML format. Generally the format is: +# +# name: value +# +# There are 2 sections: +# - global variables +# - one or more JOBS +# +# JOBS allow you to collect values from multiple sources. +# Each source will have its own set of charts. +# +# JOB parameters have to be indented (using spaces only, example below). + +# ---------------------------------------------------------------------- +# Global Variables +# These variables set the defaults for all JOBs, however each JOB +# may define its own, overriding the defaults. + +# update_every sets the default data collection frequency. +# If unset, the python.d.plugin default is used. +# update_every: 1 + +# priority controls the order of charts at the netdata dashboard. +# Lower numbers move the charts towards the top of the page. +# If unset, the default for python.d.plugin is used. +# priority: 60000 + +# retries sets the number of retries to be made in case of failures. +# If unset, the default for python.d.plugin is used. +# Attempts to restore the service are made once every update_every +# and only if the module has collected values in the past. +# retries: 5 + +# ---------------------------------------------------------------------- +# JOBS (data collection sources) +# +# The default JOBS share the same *name*. JOBS with the same name +# are mutually exclusive. Only one of them will be allowed running at +# any time. This allows autodetection to try several alternatives and +# pick the one that works. +# +# Any number of jobs is supported. +# +# All python.d.plugin JOBS (for all its modules) support a set of +# predefined parameters. These are: +# +# job_name: +# name: myname # the JOB's name as it will appear at the +# # dashboard (by default is the job_name) +# # JOBs sharing a name are mutually exclusive +# update_every: 1 # the JOB's data collection frequency +# priority: 60000 # the JOB's order on the dashboard +# retries: 5 # the JOB's number of restoration attempts +# +# Additionally to the above, smartd_log also supports the following: +# +# log_path: '/path/to/smartdlogs' # path to smartd log files. Default is /var/log/smartd +# raw_values: no # raw or normalized values on charts. Default is normalized. +# smart_attributes: '1 2 3 4 44' # add additional smart attributes charts. Default are ['1', '4', '5', '7', '9', '12', '193', '194', '197', '198', '200']. +# +# ---------------------------------------------------------------------- +# Additional information +# Plugin reads smartd log files (-A option). +# You need to add (man smartd) to /etc/default/smartmontools '-i 600 -A /var/log/smartd/' to pass additional options to smartd on startup +# Then restart smartd service and check /path/log/smartdlogs +# ls /var/log/smartd/ +# CDC_WD10EZEX_00BN5A0-WD_WCC3F7FLVZS9.ata.csv WDC_WD10EZEX_00BN5A0-WD_WCC3F7FLVZS9.ata.csv ZDC_WD10EZEX_00BN5A0-WD_WCC3F7FLVZS9.ata.csv +# +# Smartd APPEND logs at every run. Its NOT RECOMMENDED to set '-i' option below 60 sec. +# STRONGLY RECOMMENDED to create smartd conf file for logrotate +# +# RAW vs NORMALIZED values +# "Normalized value", commonly referred to as just "value". This is a most universal measurement, on the scale from 0 (bad) to some maximum (good) value. +# Maximum values are typically 100, 200 or 253. Rule of thumb is: high values are good, low values are bad. +# +# "Raw value" - the value of the attribute as it is tracked by the device, before any normalization takes place. +# Some raw numbers provide valuable insight when properly interpreted. These cases will be discussed later on. +# Raw values are typically listed in hexadecimal numbers. The raw value has different structure for different vendors and is often not meaningful as a decimal number. +# +# +# JOB configuration +# +log_path: '/var/log/smartd' |