diff options
Diffstat (limited to '')
-rw-r--r-- | fluent-bit/lib/wasm-micro-runtime-WAMR-1.2.2/samples/gui/wasm-runtime-wgl/src/platform/linux/lv_drv_conf.h | 310 |
1 files changed, 310 insertions, 0 deletions
diff --git a/fluent-bit/lib/wasm-micro-runtime-WAMR-1.2.2/samples/gui/wasm-runtime-wgl/src/platform/linux/lv_drv_conf.h b/fluent-bit/lib/wasm-micro-runtime-WAMR-1.2.2/samples/gui/wasm-runtime-wgl/src/platform/linux/lv_drv_conf.h new file mode 100644 index 000000000..d216a3e90 --- /dev/null +++ b/fluent-bit/lib/wasm-micro-runtime-WAMR-1.2.2/samples/gui/wasm-runtime-wgl/src/platform/linux/lv_drv_conf.h @@ -0,0 +1,310 @@ +/** + * @file lv_drv_conf.h + * + */ + +/* + * COPY THIS FILE AS lv_drv_conf.h + */ + +#if 1 /*Set it to "1" to enable the content*/ + +#ifndef LV_DRV_CONF_H +#define LV_DRV_CONF_H + +#include "lv_conf.h" + +/********************* + * DELAY INTERFACE + *********************/ +#define LV_DRV_DELAY_INCLUDE <stdint.h> /*Dummy include by default*/ +#define LV_DRV_DELAY_US(us) /*delay_us(us)*/ /*Delay the given number of microseconds*/ +#define LV_DRV_DELAY_MS(ms) /*delay_ms(ms)*/ /*Delay the given number of milliseconds*/ + +/********************* + * DISPLAY INTERFACE + *********************/ + +/*------------ + * Common + *------------*/ +#define LV_DRV_DISP_INCLUDE <stdint.h> /*Dummy include by default*/ +#define LV_DRV_DISP_CMD_DATA(val) /*pin_x_set(val)*/ /*Set the command/data pin to 'val'*/ +#define LV_DRV_DISP_RST(val) /*pin_x_set(val)*/ /*Set the reset pin to 'val'*/ + +/*--------- + * SPI + *---------*/ +#define LV_DRV_DISP_SPI_CS(val) /*spi_cs_set(val)*/ /*Set the SPI's Chip select to 'val'*/ +#define LV_DRV_DISP_SPI_WR_BYTE(data) /*spi_wr(data)*/ /*Write a byte the SPI bus*/ +#define LV_DRV_DISP_SPI_WR_ARRAY(adr, n) /*spi_wr_mem(adr, n)*/ /*Write 'n' bytes to SPI bus from 'adr'*/ + +/*------------------ + * Parallel port + *-----------------*/ +#define LV_DRV_DISP_PAR_CS(val) /*par_cs_set(val)*/ /*Set the Parallel port's Chip select to 'val'*/ +#define LV_DRV_DISP_PAR_SLOW /*par_slow()*/ /*Set low speed on the parallel port*/ +#define LV_DRV_DISP_PAR_FAST /*par_fast()*/ /*Set high speed on the parallel port*/ +#define LV_DRV_DISP_PAR_WR_WORD(data) /*par_wr(data)*/ /*Write a word to the parallel port*/ +#define LV_DRV_DISP_PAR_WR_ARRAY(adr, n) /*par_wr_mem(adr,n)*/ /*Write 'n' bytes to Parallel ports from 'adr'*/ + +/*************************** + * INPUT DEVICE INTERFACE + ***************************/ + +/*---------- + * Common + *----------*/ +#define LV_DRV_INDEV_INCLUDE <stdint.h> /*Dummy include by default*/ +#define LV_DRV_INDEV_RST(val) /*pin_x_set(val)*/ /*Set the reset pin to 'val'*/ +#define LV_DRV_INDEV_IRQ_READ 0 /*pn_x_read()*/ /*Read the IRQ pin*/ + +/*--------- + * SPI + *---------*/ +#define LV_DRV_INDEV_SPI_CS(val) /*spi_cs_set(val)*/ /*Set the SPI's Chip select to 'val'*/ +#define LV_DRV_INDEV_SPI_XCHG_BYTE(data) 0 /*spi_xchg(val)*/ /*Write 'val' to SPI and give the read value*/ + +/*--------- + * I2C + *---------*/ +#define LV_DRV_INDEV_I2C_START /*i2c_start()*/ /*Make an I2C start*/ +#define LV_DRV_INDEV_I2C_STOP /*i2c_stop()*/ /*Make an I2C stop*/ +#define LV_DRV_INDEV_I2C_RESTART /*i2c_restart()*/ /*Make an I2C restart*/ +#define LV_DRV_INDEV_I2C_WR(data) /*i2c_wr(data)*/ /*Write a byte to the I1C bus*/ +#define LV_DRV_INDEV_I2C_READ(last_read) 0 /*i2c_rd()*/ /*Read a byte from the I2C bud*/ + + +/********************* + * DISPLAY DRIVERS + *********************/ + +/*------------------- + * Monitor of PC + *-------------------*/ +#ifndef USE_MONITOR +# define USE_MONITOR 1 +#endif + +#if USE_MONITOR +# define MONITOR_HOR_RES LV_HOR_RES_MAX +# define MONITOR_VER_RES LV_VER_RES_MAX + +/* Scale window by this factor (useful when simulating small screens) */ +# define MONITOR_ZOOM 1 + +/* Used to test true double buffering with only address changing. + * Set LV_VDB_SIZE = (LV_HOR_RES * LV_VER_RES) and LV_VDB_DOUBLE = 1 and LV_COLOR_DEPTH = 32" */ +# define MONITOR_DOUBLE_BUFFERED 0 + +/*Eclipse: <SDL2/SDL.h> Visual Studio: <SDL.h>*/ +# define MONITOR_SDL_INCLUDE_PATH <SDL2/SDL.h> + +/*Different rendering might be used if running in a Virtual machine*/ +# define MONITOR_VIRTUAL_MACHINE 0 + +/*Open two windows to test multi display support*/ +# define MONITOR_DUAL 0 +#endif + +/*----------------------------------- + * Native Windows (including mouse) + *----------------------------------*/ +#ifndef USE_WINDOWS +# define USE_WINDOWS 0 +#endif + +#define USE_WINDOWS 0 +#if USE_WINDOWS +# define WINDOW_HOR_RES 480 +# define WINDOW_VER_RES 320 +#endif + +/*---------------- + * SSD1963 + *--------------*/ +#ifndef USE_SSD1963 +# define USE_SSD1963 0 +#endif + +#if USE_SSD1963 +# define SSD1963_HOR_RES LV_HOR_RES +# define SSD1963_VER_RES LV_VER_RES +# define SSD1963_HT 531 +# define SSD1963_HPS 43 +# define SSD1963_LPS 8 +# define SSD1963_HPW 10 +# define SSD1963_VT 288 +# define SSD1963_VPS 12 +# define SSD1963_FPS 4 +# define SSD1963_VPW 10 +# define SSD1963_HS_NEG 0 /*Negative hsync*/ +# define SSD1963_VS_NEG 0 /*Negative vsync*/ +# define SSD1963_ORI 0 /*0, 90, 180, 270*/ +# define SSD1963_COLOR_DEPTH 16 +#endif + +/*---------------- + * R61581 + *--------------*/ +#ifndef USE_R61581 +# define USE_R61581 0 +#endif + +#if USE_R61581 +# define R61581_HOR_RES LV_HOR_RES +# define R61581_VER_RES LV_VER_RES +# define R61581_HSPL 0 /*HSYNC signal polarity*/ +# define R61581_HSL 10 /*HSYNC length (Not Implemented)*/ +# define R61581_HFP 10 /*Horitontal Front poarch (Not Implemented)*/ +# define R61581_HBP 10 /*Horitontal Back poarch (Not Implemented */ +# define R61581_VSPL 0 /*VSYNC signal polarity*/ +# define R61581_VSL 10 /*VSYNC length (Not Implemented)*/ +# define R61581_VFP 8 /*Vertical Front poarch*/ +# define R61581_VBP 8 /*Vertical Back poarch */ +# define R61581_DPL 0 /*DCLK signal polarity*/ +# define R61581_EPL 1 /*ENABLE signal polarity*/ +# define R61581_ORI 0 /*0, 180*/ +# define R61581_LV_COLOR_DEPTH 16 /*Fix 16 bit*/ +#endif + +/*------------------------------ + * ST7565 (Monochrome, low res.) + *-----------------------------*/ +#ifndef USE_ST7565 +# define USE_ST7565 0 +#endif + +#if USE_ST7565 +/*No settings*/ +#endif /*USE_ST7565*/ + +/*----------------------------------------- + * Linux frame buffer device (/dev/fbx) + *-----------------------------------------*/ +#ifndef USE_FBDEV +# define USE_FBDEV 1 +#endif + +#if USE_FBDEV +# define FBDEV_PATH "/dev/fb0" +#endif + +/********************* + * INPUT DEVICES + *********************/ + +/*-------------- + * XPT2046 + *--------------*/ +#ifndef USE_XPT2046 +# define USE_XPT2046 0 +#endif + +#if USE_XPT2046 +# define XPT2046_HOR_RES 480 +# define XPT2046_VER_RES 320 +# define XPT2046_X_MIN 200 +# define XPT2046_Y_MIN 200 +# define XPT2046_X_MAX 3800 +# define XPT2046_Y_MAX 3800 +# define XPT2046_AVG 4 +# define XPT2046_INV 0 +#endif + +/*----------------- + * FT5406EE8 + *-----------------*/ +#ifndef USE_FT5406EE8 +# define USE_FT5406EE8 0 +#endif + +#if USE_FT5406EE8 +# define FT5406EE8_I2C_ADR 0x38 /*7 bit address*/ +#endif + +/*--------------- + * AD TOUCH + *--------------*/ +#ifndef USE_AD_TOUCH +# define USE_AD_TOUCH 0 +#endif + +#if USE_AD_TOUCH +/*No settings*/ +#endif + + +/*--------------------------------------- + * Mouse or touchpad on PC (using SDL) + *-------------------------------------*/ +#ifndef USE_MOUSE +# define USE_MOUSE 1 +#endif + +#if USE_MOUSE +/*No settings*/ +#endif + +/*------------------------------------------- + * Mousewheel as encoder on PC (using SDL) + *------------------------------------------*/ +#ifndef USE_MOUSEWHEEL +# define USE_MOUSEWHEEL 1 +#endif + +#if USE_MOUSEWHEEL +/*No settings*/ +#endif + +/*------------------------------------------------- + * Touchscreen as libinput interface (for Linux based systems) + *------------------------------------------------*/ +#ifndef USE_LIBINPUT +# define USE_LIBINPUT 0 +#endif + +#if USE_LIBINPUT +# define LIBINPUT_NAME "/dev/input/event0" /*You can use the "evtest" Linux tool to get the list of devices and test them*/ +#endif /*USE_LIBINPUT*/ + +/*------------------------------------------------- + * Mouse or touchpad as evdev interface (for Linux based systems) + *------------------------------------------------*/ +#ifndef USE_EVDEV +# define USE_EVDEV 0 +#endif + +#if USE_EVDEV +# define EVDEV_NAME "/dev/input/event0" /*You can use the "evtest" Linux tool to get the list of devices and test them*/ +# define EVDEV_SWAP_AXES 0 /*Swap the x and y axes of the touchscreen*/ + +# define EVDEV_SCALE 0 /* Scale input, e.g. if touchscreen resolution does not match display resolution */ +# if EVDEV_SCALE +# define EVDEV_SCALE_HOR_RES (4096) /* Horizontal resolution of touchscreen */ +# define EVDEV_SCALE_VER_RES (4096) /* Vertical resolution of touchscreen */ +# endif /*EVDEV_SCALE*/ + +# define EVDEV_CALIBRATE 0 /*Scale and offset the touchscreen coordinates by using maximum and minimum values for each axis*/ +# if EVDEV_CALIBRATE +# define EVDEV_HOR_MIN 3800 /*If EVDEV_XXX_MIN > EVDEV_XXX_MAX the XXX axis is automatically inverted*/ +# define EVDEV_HOR_MAX 200 +# define EVDEV_VER_MIN 200 +# define EVDEV_VER_MAX 3800 +# endif /*EVDEV_SCALE*/ +#endif /*USE_EVDEV*/ + +/*------------------------------- + * Keyboard of a PC (using SDL) + *------------------------------*/ +#ifndef USE_KEYBOARD +# define USE_KEYBOARD 1 +#endif + +#if USE_KEYBOARD +/*No settings*/ +#endif + +#endif /*LV_DRV_CONF_H*/ + +#endif /*End of "Content enable"*/ |