diff options
Diffstat (limited to '')
| -rw-r--r-- | streaming/stream.conf (renamed from conf.d/stream.conf) | 32 |
1 files changed, 22 insertions, 10 deletions
diff --git a/conf.d/stream.conf b/streaming/stream.conf index d0c9a8b18..493eba37c 100644 --- a/conf.d/stream.conf +++ b/streaming/stream.conf @@ -39,17 +39,25 @@ # If the destination line above does not specify a port, use this default port = 19999 + # filter the charts to be streamed + # netdata SIMPLE PATTERN: + # - space separated list of patterns (use \ to include spaces in patterns) + # - use * as wildcard, any number of times within each pattern + # - prefix a pattern with ! for a negative match (ie not stream the charts it matches) + # - the order of patterns is important (left to right) + # To send all except a few, use: !this !that * (ie append a wildcard pattern) + send charts matching = * + # The buffer to use for sending metrics. - # 1MB is good for 10-20 seconds of data, so increase this - # if you expect latencies. + # 1MB is good for 10-20 seconds of data, so increase this if you expect latencies. + # The buffer is flushed on reconnects (this will not prevent gaps at the charts). buffer size bytes = 1048576 # If the connection fails, or it disconnects, # retry after that many seconds. reconnect delay seconds = 5 - # Attempt to sync the clock the of the master with the clock of the - # slave for that many iterations, when starting. + # Sync the clock of the charts for that many iterations, when starting. initial clock resync iterations = 60 @@ -62,8 +70,9 @@ # netdata searches for options in this order: # # a) master netdata settings (netdata.conf) -# b) [API_KEY] section (below, settings for the API key) -# c) [MACHINE_GUID] section (below, settings for each machine) +# b) [stream] section (above) +# c) [API_KEY] section (below, settings for the API key) +# d) [MACHINE_GUID] section (below, settings for each machine) # # You can combine the above (the more specific setting will be used). @@ -95,7 +104,7 @@ # If you don't set it here, the memory mode of netdata.conf will be used. # Valid modes: # save save on exit, load on start - # map like swap (continuously syncing to disks) + # map like swap (continuously syncing to disks - you need SSD) # ram keep it in RAM, don't touch the disk # none no database at all (use this on headless proxies) default memory mode = ram @@ -106,7 +115,7 @@ # no do not enable alarms # auto enable alarms, only when the sending netdata is connected # You can also set it per host, below. - # The default is the same as to netdata.conf + # The default is taken from [health].enabled of netdata.conf health enabled by default = auto # postpone alarms for a short period after the sender is connected @@ -120,15 +129,16 @@ multiple connections = allow # need to route metrics differently? set these. - # the defaults are the ones at the [stream] section + # the defaults are the ones at the [stream] section (above) #default proxy enabled = yes | no #default proxy destination = IP:PORT IP:PORT ... #default proxy api key = API_KEY + #default proxy send charts matching = * # ----------------------------------------------------------------------------- # 3. PER SENDING HOST SETTINGS, ON MASTER NETDATA -# THIS IS OPTIONAL - YOU DON'T NEED IT +# THIS IS OPTIONAL - YOU DON'T HAVE TO CONFIGURE IT # This section exists to give you finer control of the master settings for each # slave host, when the same API key is used by many netdata slaves / proxies. @@ -174,6 +184,8 @@ multiple connections = allow # need to route metrics differently? + # the defaults are the ones at the [API KEY] section #proxy enabled = yes | no #proxy destination = IP:PORT IP:PORT ... #proxy api key = API_KEY + #proxy send charts matching = * |