From 1e6c93250172946eeb38e94a92a1fd12c9d3011e Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Wed, 7 Nov 2018 13:22:44 +0100 Subject: Merging upstream version 1.11.0+dfsg. Signed-off-by: Daniel Baumann --- conf.d/stream.conf | 179 ----------------------------------------------------- 1 file changed, 179 deletions(-) delete mode 100644 conf.d/stream.conf (limited to 'conf.d/stream.conf') diff --git a/conf.d/stream.conf b/conf.d/stream.conf deleted file mode 100644 index d0c9a8b18..000000000 --- a/conf.d/stream.conf +++ /dev/null @@ -1,179 +0,0 @@ -# netdata configuration for aggregating data from remote hosts -# -# API keys authorize a pair of sending-receiving netdata servers. -# Once their communication is authorized, they can exchange metrics for any -# number of hosts. -# -# You can generate API keys, with the linux command: uuidgen - - -# ----------------------------------------------------------------------------- -# 1. ON SLAVE NETDATA - THE ONE THAT WILL BE SENDING METRICS - -[stream] - # Enable this on slaves, to have them send metrics. - enabled = no - - # Where is the receiving netdata? - # A space separated list of: - # - # [PROTOCOL:]HOST[%INTERFACE][:PORT] - # - # If many are given, the first available will get the metrics. - # - # PROTOCOL = tcp, udp, or unix (only tcp and unix are supported by masters) - # HOST = an IPv4, IPv6 IP, or a hostname, or a unix domain socket path. - # IPv6 IPs should be given with brackets [ip:address] - # INTERFACE = the network interface to use (only for IPv6) - # PORT = the port number or service name (/etc/services) - # - # This communication is not HTTP (it cannot be proxied by web proxies). - destination = - - # The API_KEY to use (as the sender) - api key = - - # The timeout to connect and send metrics - timeout seconds = 60 - - # If the destination line above does not specify a port, use this - default port = 19999 - - # The buffer to use for sending metrics. - # 1MB is good for 10-20 seconds of data, so increase this - # if you expect latencies. - buffer size bytes = 1048576 - - # If the connection fails, or it disconnects, - # retry after that many seconds. - reconnect delay seconds = 5 - - # Attempt to sync the clock the of the master with the clock of the - # slave for that many iterations, when starting. - initial clock resync iterations = 60 - - -# ----------------------------------------------------------------------------- -# 2. ON MASTER NETDATA - THE ONE THAT WILL BE RECEIVING METRICS - -# You can have one API key per slave, -# or the same API key for all slaves. -# -# netdata searches for options in this order: -# -# a) master netdata settings (netdata.conf) -# b) [API_KEY] section (below, settings for the API key) -# c) [MACHINE_GUID] section (below, settings for each machine) -# -# You can combine the above (the more specific setting will be used). - -# API key authentication -# If the key is not listed here, it will not be able to push metrics. - -# [API_KEY] is [YOUR-API-KEY], i.e [11111111-2222-3333-4444-555555555555] -[API_KEY] - # Default settings for this API key - - # You can disable the API key, by setting this to: no - # The default (for unknown API keys) is: no - enabled = no - - # A list of simple patterns matching the IPs of the servers that - # will be pushing metrics using this API key. - # The metrics are received via the API port, so the same IPs - # should also be matched at netdata.conf [web].allow connections from - allow from = * - - # The default history in entries, for all hosts using this API key. - # You can also set it per host below. - # If you don't set it here, the history size of the central netdata - # will be used. - default history = 3600 - - # The default memory mode to be used for all hosts using this API key. - # You can also set it per host below. - # If you don't set it here, the memory mode of netdata.conf will be used. - # Valid modes: - # save save on exit, load on start - # map like swap (continuously syncing to disks) - # ram keep it in RAM, don't touch the disk - # none no database at all (use this on headless proxies) - default memory mode = ram - - # Shall we enable health monitoring for the hosts using this API key? - # 3 possible values: - # yes enable alarms - # no do not enable alarms - # auto enable alarms, only when the sending netdata is connected - # You can also set it per host, below. - # The default is the same as to netdata.conf - health enabled by default = auto - - # postpone alarms for a short period after the sender is connected - default postpone alarms on connect seconds = 60 - - # allow or deny multiple connections for the same host? - # If you are sure all your netdata have their own machine GUID, - # set this to 'allow', since it allows faster reconnects. - # When set to 'deny', new connections for a host will not be - # accepted until an existing connection is cleared. - multiple connections = allow - - # need to route metrics differently? set these. - # the defaults are the ones at the [stream] section - #default proxy enabled = yes | no - #default proxy destination = IP:PORT IP:PORT ... - #default proxy api key = API_KEY - - -# ----------------------------------------------------------------------------- -# 3. PER SENDING HOST SETTINGS, ON MASTER NETDATA -# THIS IS OPTIONAL - YOU DON'T NEED IT - -# This section exists to give you finer control of the master settings for each -# slave host, when the same API key is used by many netdata slaves / proxies. -# -# Each netdata has a unique GUID - generated the first time netdata starts. -# You can find it at /var/lib/netdata/registry/netdata.public.unique.id -# (at the slave). -# -# The host sending data will have one. If the host is not ephemeral, -# you can give settings for each sending host here. - -[MACHINE_GUID] - # enable this host: yes | no - # When disabled, the master will not receive metrics for this host. - # THIS IS NOT A SECURITY MECHANISM - AN ATTACKER CAN SET ANY OTHER GUID. - # Use only the API key for security. - enabled = no - - # A list of simple patterns matching the IPs of the servers that - # will be pushing metrics using this MACHINE GUID. - # The metrics are received via the API port, so the same IPs - # should also be matched at netdata.conf [web].allow connections from - # and at stream.conf [API_KEY].allow from - allow from = * - - # The number of entries in the database - history = 3600 - - # The memory mode of the database: save | map | ram | none - memory mode = save - - # Health / alarms control: yes | no | auto - health enabled = yes - - # postpone alarms when the sender connects - postpone alarms on connect seconds = 60 - - # allow or deny multiple connections for the same host? - # If you are sure all your netdata have their own machine GUID, - # set this to 'allow', since it allows faster reconnects. - # When set to 'deny', new connections for a host will not be - # accepted until an existing connection is cleared. - multiple connections = allow - - # need to route metrics differently? - #proxy enabled = yes | no - #proxy destination = IP:PORT IP:PORT ... - #proxy api key = API_KEY -- cgit v1.2.3