Adding debian version 3.20230719.1~deb11u1.debian/3.20230719.1_deb11u1debian

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 100 insertions, 0 deletions

diff --git a/debian/README.Debian b/debian/README.Debian
new file mode 100644
index 0000000..b0116a4
--- /dev/null
+++ b/debian/README.Debian
@@ -0,0 +1,100 @@
+amd64-microcode for Debian
+--------------------------
+
+Introduction:
+
+AMD AMD64 processors are capable of field-upgrading their control program
+(microcode).  These microcode updates correct processor errata, and are
+often important for safe, correct system operation.
+
+While most of the microcode updates fix problems that happen extremely
+rarely, there are enough updates fixing issues that would cause system
+lockup, memory corruption, or unpredictable system behavior, to warrant
+taking it seriously.
+
+Microcode updates are ephemeral: they will be lost after a processor hard
+reset or after the processor is powered off.  They must be reapplied at
+every boot and after the system wakes up from suspend to RAM or disk.
+
+Updating the processor microcode is the responsibility of the system
+firmware (BIOS or EFI).  However, not all vendors will release timely
+updates for their firmware when AMD releases updated microcode, and most
+users don't update their system firmware in a timely fashion (or at all)
+anyway.
+
+The end result is that, unless some other method of distributing microcode
+updates is in place, the processor in many systems will be running with
+outdated microcode, increasing the chances of incorrect system operation.
+
+Debian can apply microcode updates to the system processors during the
+operating system boot automatically.  This requires the use of a suitably
+configured Linux kernel 3.14 or later, and an initramfs.
+
+
+Installing microcode updates:
+
+For the Debian default kernel, it is enough to install the amd64-microcode
+package as well as the initramfs-tools package and the microcode update
+will be applied automatically at the next reboot.
+
+It is also possible to use "dracut" instead of initramfs-tools, but the
+support for early microcode updates must be enabled manually in
+dracut.conf (set the option "early_microcode=yes").  Force an update of
+the initramfs using dracut, and reboot.  Note that since Linux kernel 4.4,
+one must use dracut 044 or later.
+
+Applying the microcode updates without the use of an early initramfs is
+not automatically supported anymore, due to future safety concerns.
+However, the local administrator may trigger an immediate microcode update
+attempt at any time, at her own risk:
+
+  USING AN INITRAMFS+REBOOT IS SAFER.  DO THIS ONLY WHEN YOU KNOW BETTER:
+  as root:
+  echo 1 > /sys/devices/system/cpu/microcode/reload
+
+
+RECOVERY PROCEDURE:
+
+It is possible for a microcode update to not work well, or to not work at
+all on specific system models.  This is very rare when using the safe
+microcode update procedure described above and an up-to-date Linux kernel,
+but it has happened at least once.
+
+Should you experience problems because of the microcode update, you will
+have to bypass the microcode update process that happens during operating
+system startup (boot), and remove the amd64-microcode package until the
+underlying issue is fixed.
+
+To bypass the microcode update during system startup, you must instruct the
+boot loader (grub, lilo, etc) to pass the "dis_ucode_ldr" parameter
+(without the quotes) to the kernel.
+
+If your system uses grub (the default bootloader in Debian):
+
+  1. Access the grub menu during boot (press and hold the left "Shift"
+     key right after starting the system up if you don't see a grub menu
+     during boot);
+
+  2. Move the highlight/cursor to the kernel/boot option you want to
+     use, and press the "e" key to edit it;
+
+  3. Locate the line that starts with "linux" using the cursor
+     keys.  You must add the word "dis_ucode_ldr" (without the quotes) to
+     the end of that line;
+
+  4. Press "Ctrl+X" to start (boot) the system.  The microcode updates
+     will be skipped.
+
+After the system is running, remove or purge the amd64-microcode package.
+
+If removing/purging the package doesn't do it automatically for some
+reason, refresh the initramfs using the "update-initramfs -u" command (as
+the root user), and possibly "update-initramfs -u -k <kernel version>".
+
+"dracut" users, please refer to the dracut documentation on how to update
+the initramfs images for every installed kernel.
+
+Please report any issues caused by microcode updates to the mailing-list or
+to the Debian bug tracker.
+
+ -- Henrique de Moraes Holschuh <hmh@debian.org>, 2016-04-05