blob: 8b03ae7a2c72c089ea503396bfc644bc7218f189 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
|
### router/200_exim4-config_primary
#################################
# This file holds the primary router, responsible for nonlocal mails
.ifdef DCconfig_internet
# configtype=internet
#
# deliver mail to the recipient if recipient domain is a domain we
# relay for. We do not ignore any target hosts here since delivering to
# a site local or even a link local address might be wanted here, and if
# such an address has found its way into the MX record of such a domain,
# the local admin is probably in a place where that broken MX record
# could be fixed.
dnslookup_relay_to_domains:
debug_print = "R: dnslookup_relay_to_domains for $local_part@$domain"
driver = dnslookup
domains = ! +local_domains : +relay_to_domains
transport = remote_smtp
same_domain_copy_routing = yes
dnssec_request_domains = *
no_more
# deliver mail directly to the recipient. This router is only reached
# for domains that we do not relay for. Since we most probably can't
# have broken MX records pointing to site local or link local IP
# addresses fixed, we ignore target hosts pointing to these addresses.
dnslookup:
debug_print = "R: dnslookup for $local_part@$domain"
driver = dnslookup
domains = ! +local_domains
transport = remote_smtp
same_domain_copy_routing = yes
# ignore private rfc1918 and APIPA addresses
ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\
172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16 :\
255.255.255.255
dnssec_request_domains = *
no_more
.endif
.ifdef DCconfig_local
# configtype=local
#
# Stand-alone system, so generate an error for mail to a non-local domain
nonlocal:
debug_print = "R: nonlocal for $local_part@$domain"
driver = redirect
domains = ! +local_domains
allow_fail
data = :fail: Mailing to remote domains not supported
no_more
.endif
.ifdef DCconfig_smarthost DCconfig_satellite
# configtype=smarthost or configtype=satellite
#
# Send all non-local mail to a single other machine (smarthost).
#
# This means _ALL_ non-local mail goes to the smarthost. This will most
# probably not do what you want for domains that are listed in
# relay_domains. The most typical use for relay_domains is to control
# relaying for incoming e-mail on secondary MX hosts. In that case,
# it doesn't make sense to send the mail to the smarthost since the
# smarthost will probably send the message right back here, causing a
# loop.
#
# If you want to use a smarthost while being secondary MX for some
# domains, you'll need to copy the dnslookup_relay_to_domains router
# here so that mail to relay_domains is handled separately.
smarthost:
debug_print = "R: smarthost for $local_part@$domain"
driver = manualroute
domains = ! +local_domains
transport = remote_smtp_smarthost
route_list = * DCsmarthost byname
host_find_failed = ignore
same_domain_copy_routing = yes
no_more
.endif
# The "no_more" above means that all later routers are for
# domains in the local_domains list, i.e. just like Exim 3 directors.
|
