Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

10 files changed, 328 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt b/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt
new file mode 100644
index 000000000..261df2799
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt
@@ -0,0 +1,15 @@
+88pm860x-backlight bindings
+
+Optional properties:
+  - marvell,88pm860x-iset: Current supplies on backlight device.
+  - marvell,88pm860x-pwm: PWM frequency on backlight device.
+
+Example:
+
+	backlights {
+		backlight-0 {
+			marvell,88pm860x-iset = <4>;
+			marvell,88pm860x-pwm = <3>;
+		};
+		backlight-2 {
+		};
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 000000000..230abdefd
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible:		should be "arc,arc2c0608"
+- reg:			slave address
+
+Optional properties:
+- default-brightness:	brightness value on boot, value from: 0-4095
+- label:		The name of the backlight device
+			See Documentation/devicetree/bindings/leds/common.txt
+- led-sources:		List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0:	setting for register ILED_CONFIG_0
+- arc,led-config-1:	setting for register ILED_CONFIG_1
+- arc,dim-freq:		PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config:	setting for register CONFIG_COMP
+- arc,filter-config:	setting for register FILTER_CONFIG
+- arc,trim-config:	setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+	compatible = "arc,arc2c0608";
+	reg = <0x30>;
+	default-brightness = <500>;
+	label = "lcd-backlight";
+	linux,default-trigger = "backlight";
+	led-sources = <0 1 2 5>;
+};
+
diff --git a/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt
new file mode 100644
index 000000000..321be6640
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt
@@ -0,0 +1,16 @@
+gpio-backlight bindings
+
+Required properties:
+  - compatible: "gpio-backlight"
+  - gpios: describes the gpio that is used for enabling/disabling the backlight.
+    refer to bindings/gpio/gpio.txt for more details.
+
+Optional properties:
+  - default-on: enable the backlight at boot.
+
+Example:
+	backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
diff --git a/Documentation/devicetree/bindings/leds/backlight/lp855x.txt b/Documentation/devicetree/bindings/leds/backlight/lp855x.txt
new file mode 100644
index 000000000..88f56641f
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/lp855x.txt
@@ -0,0 +1,72 @@
+lp855x bindings
+
+Required properties:
+  - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553",
+                "ti,lp8555", "ti,lp8556", "ti,lp8557"
+  - reg: I2C slave address (u8)
+  - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device.
+
+Optional properties:
+  - bl-name: Backlight device name (string)
+  - init-brt: Initial value of backlight brightness (u8)
+  - pwm-period: PWM period value. Set only PWM input mode used (u32)
+  - rom-addr: Register address of ROM area to be updated (u8)
+  - rom-val: Register value to be updated (u8)
+  - power-supply: Regulator which controls the 3V rail
+  - enable-supply: Regulator which controls the EN/VDDIO input
+
+Example:
+
+	/* LP8555 */
+	backlight@2c {
+		compatible = "ti,lp8555";
+		reg = <0x2c>;
+
+		dev-ctrl = /bits/ 8 <0x00>;
+		pwm-period = <10000>;
+
+		/* 4V OV, 4 output LED0 string enabled */
+		rom_14h {
+			rom-addr = /bits/ 8 <0x14>;
+			rom-val = /bits/ 8 <0xcf>;
+		};
+
+		/* Heavy smoothing, 24ms ramp time step */
+		rom_15h {
+			rom-addr = /bits/ 8 <0x15>;
+			rom-val = /bits/ 8 <0xc7>;
+		};
+
+		/* 4 output LED1 string enabled */
+		rom_19h {
+			rom-addr = /bits/ 8 <0x19>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+	};
+
+	/* LP8556 */
+	backlight@2c {
+		compatible = "ti,lp8556";
+		reg = <0x2c>;
+
+		bl-name = "lcd-bl";
+		dev-ctrl = /bits/ 8 <0x85>;
+		init-brt = /bits/ 8 <0x10>;
+	};
+
+	/* LP8557 */
+	backlight@2c {
+		compatible = "ti,lp8557";
+		reg = <0x2c>;
+		enable-supply = <&backlight_vddio>;
+		power-supply = <&backlight_vdd>;
+
+		dev-ctrl = /bits/ 8 <0x41>;
+		init-brt = /bits/ 8 <0x0a>;
+
+		/* 4V OV, 4 output LED string enabled */
+		rom_14h {
+			rom-addr = /bits/ 8 <0x14>;
+			rom-val = /bits/ 8 <0xcf>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt
new file mode 100644
index 000000000..b4cffdaa4
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt
@@ -0,0 +1,10 @@
+88pm860x-backlight bindings
+
+Optional properties:
+  - maxim,max8925-dual-string: whether support dual string
+
+Example:
+
+	backlights {
+		maxim,max8925-dual-string = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt b/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt
new file mode 100644
index 000000000..e5b294daf
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt
@@ -0,0 +1,42 @@
+Binding for Qualcomm PM8941 WLED driver
+
+Required properties:
+- compatible: should be "qcom,pm8941-wled"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+	default: 2048
+- label: The name of the backlight device
+- qcom,cs-out: bool; enable current sink output
+- qcom,cabc: bool; enable content adaptive backlight control
+- qcom,ext-gen: bool; use externally generated modulator signal to dim
+- qcom,current-limit: mA; per-string current limit; value from 0 to 25
+	default: 20mA
+- qcom,current-boost-limit: mA; boost current limit; one of:
+	105, 385, 525, 805, 980, 1260, 1400, 1680
+	default: 805mA
+- qcom,switching-freq: kHz; switching frequency; one of:
+	600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371,
+	1600, 1920, 2400, 3200, 4800, 9600,
+	default: 1600kHz
+- qcom,ovp: V; Over-voltage protection limit; one of:
+	27, 29, 32, 35
+	default: 29V
+- qcom,num-strings: #; number of led strings attached; value from 1 to 3
+	default: 2
+
+Example:
+
+pm8941-wled@d800 {
+	compatible = "qcom,pm8941-wled";
+	reg = <0xd800>;
+	label = "backlight";
+
+	qcom,cs-out;
+	qcom,current-limit = <20>;
+	qcom,current-boost-limit = <805>;
+	qcom,switching-freq = <1600>;
+	qcom,ovp = <29>;
+	qcom,num-strings = <2>;
+};
diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
new file mode 100644
index 000000000..64fa2fbd9
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
@@ -0,0 +1,61 @@
+pwm-backlight bindings
+
+Required properties:
+  - compatible: "pwm-backlight"
+  - pwms: OF device-tree PWM specification (see PWM binding[0])
+  - power-supply: regulator for supply voltage
+
+Optional properties:
+  - pwm-names: a list of names for the PWM devices specified in the
+               "pwms" property (see PWM binding[0])
+  - enable-gpios: contains a single GPIO specifier for the GPIO which enables
+                  and disables the backlight (see GPIO binding[1])
+  - post-pwm-on-delay-ms: Delay in ms between setting an initial (non-zero) PWM
+                          and enabling the backlight using GPIO.
+  - pwm-off-delay-ms: Delay in ms between disabling the backlight using GPIO
+                      and setting PWM value to 0.
+  - brightness-levels: Array of distinct brightness levels. Typically these
+                       are in the range from 0 to 255, but any range starting at
+                       0 will do. The actual brightness level (PWM duty cycle)
+                       will be interpolated from these values. 0 means a 0% duty
+                       cycle (darkest/off), while the last value in the array
+                       represents a 100% duty cycle (brightest).
+  - default-brightness-level: The default brightness level (index into the
+                              array defined by the "brightness-levels" property).
+  - num-interpolated-steps: Number of interpolated steps between each value
+                            of brightness-levels table. This way a high
+                            resolution pwm duty cycle can be used without
+                            having to list out every possible value in the
+                            brightness-level array.
+
+[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+
+		power-supply = <&vdd_bl_reg>;
+		enable-gpios = <&gpio 58 0>;
+		post-pwm-on-delay-ms = <10>;
+		pwm-off-delay-ms = <10>;
+	};
+
+Example using num-interpolation-steps:
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <0 2048 4096 8192 16384 65535>;
+		num-interpolated-steps = <2048>;
+		default-brightness-level = <4096>;
+
+		power-supply = <&vdd_bl_reg>;
+		enable-gpios = <&gpio 58 0>;
+	};
diff --git a/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt
new file mode 100644
index 000000000..8bf2940f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt
@@ -0,0 +1,29 @@
+SKY81452-backlight bindings
+
+Required properties:
+- compatible		: Must be "skyworks,sky81452-backlight"
+
+Optional properties:
+- name			: Name of backlight device. Default is 'lcd-backlight'.
+- gpios			: GPIO to use to EN pin.
+			See Documentation/devicetree/bindings/gpio/gpio.txt
+- led-sources		: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+- skyworks,ignore-pwm	: Ignore both PWM input
+- skyworks,dpwm-mode	: Enable DPWM dimming mode, otherwise Analog dimming.
+- skyworks,phase-shift	: Enable phase shift mode
+- skyworks,short-detection-threshold-volt
+			: It should be one of 4, 5, 6 and 7V.
+- skyworks,current-limit-mA
+			: It should be 2300mA or 2750mA.
+
+Example:
+
+	backlight {
+		compatible = "skyworks,sky81452-backlight";
+		name = "pwm-backlight";
+		led-sources = <0 1 2 5>;
+		skyworks,ignore-pwm;
+		skyworks,phase-shift;
+		skyworks,current-limit-mA = <2300>;
+	};
diff --git a/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt
new file mode 100644
index 000000000..5fb9279ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt
@@ -0,0 +1,27 @@
+TPS65217 family of regulators
+
+The TPS65217 chip contains a boost converter and current sinks which can be
+used to drive LEDs for use as backlights.
+
+Required properties:
+- compatible: "ti,tps65217"
+- reg: I2C slave address
+- backlight: node for specifying WLED1 and WLED2 lines in TPS65217
+- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level)
+- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000
+- default-brightness: valid values: 0-100
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+	tps: tps@24 {
+		reg = <0x24>;
+		compatible = "ti,tps65217";
+		backlight {
+			isel = <1>;  /* 1 - ISET1, 2 ISET2 */
+			fdim = <100>; /* TPS65217_BL_FDIM_100HZ */
+			default-brightness = <50>;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt
new file mode 100644
index 000000000..ff5c92138
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/zii,rave-sp-backlight.txt
@@ -0,0 +1,23 @@
+Zodiac Inflight Innovations RAVE Supervisory Processor Backlight Bindings
+
+RAVE SP backlight device is a "MFD cell" device corresponding to
+backlight functionality of RAVE Supervisory Processor. It is expected
+that its Device Tree node is specified as a child of the node
+corresponding to the parent RAVE SP device (as documented in
+Documentation/devicetree/bindings/mfd/zii,rave-sp.txt)
+
+Required properties:
+
+- compatible: Should be "zii,rave-sp-backlight"
+
+Example:
+
+	rave-sp {
+		compatible = "zii,rave-sp-rdu1";
+		current-speed = <38400>;
+
+		backlight {
+			compatible = "zii,rave-sp-backlight";
+		};
+	}
+