Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

37 files changed, 1761 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
new file mode 100644
index 000000000..5940ca11c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
@@ -0,0 +1,19 @@
+* Analog Devices AD5820 autofocus coil
+
+Required Properties:
+
+  - compatible: Must contain "adi,ad5820"
+
+  - reg: I2C slave address
+
+  - VANA-supply: supply of voltage for VANA pin
+
+Example:
+
+       ad5820: coil@c {
+               compatible = "adi,ad5820";
+               reg = <0x0c>;
+
+               VANA-supply = <&vaux4>;
+       };
+
diff --git a/Documentation/devicetree/bindings/media/i2c/adp1653.txt b/Documentation/devicetree/bindings/media/i2c/adp1653.txt
new file mode 100644
index 000000000..4cce0de40
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adp1653.txt
@@ -0,0 +1,38 @@
+* Analog Devices ADP1653 flash LED driver
+
+Required Properties:
+
+  - compatible: Must contain "adi,adp1653"
+
+  - reg: I2C slave address
+
+  - enable-gpios: Specifier of the GPIO connected to EN pin
+
+There are two LED outputs available - flash and indicator. One LED is
+represented by one child node, nodes need to be named "flash" and "indicator".
+
+Required properties of the LED child node:
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Required properties of the flash LED child node:
+
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+	adp1653: led-controller@30 {
+		compatible = "adi,adp1653";
+		reg = <0x30>;
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
+
+		flash {
+			flash-timeout-us = <500000>;
+			flash-max-microamp = <320000>;
+			led-max-microamp = <50000>;
+		};
+		indicator {
+			led-max-microamp = <17500>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt
new file mode 100644
index 000000000..552b6a82c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt
@@ -0,0 +1,49 @@
+* Analog Devices ADV7180 analog video decoder family
+
+The adv7180 family devices are used to capture analog video to different
+digital interfaces like MIPI CSI-2 or parallel video.
+
+Required Properties :
+- compatible : value must be one of
+		"adi,adv7180"
+		"adi,adv7180cp"
+		"adi,adv7180st"
+		"adi,adv7182"
+		"adi,adv7280"
+		"adi,adv7280-m"
+		"adi,adv7281"
+		"adi,adv7281-m"
+		"adi,adv7281-ma"
+		"adi,adv7282"
+		"adi,adv7282-m"
+
+Device nodes of "adi,adv7180cp" and "adi,adv7180st" must contain one
+'port' child node per device input and output port, in accordance with the
+video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+nodes are numbered as follows.
+
+  Port		adv7180cp	adv7180st
+-------------------------------------------------------------------
+  Input		0-2		0-5
+  Output	3		6
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties :
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+  if any.
+
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		adv7180@21 {
+			compatible = "adi,adv7180";
+			reg = <0x21>;
+		};
+		...
+	};
+
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
new file mode 100644
index 000000000..5653bc242
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
@@ -0,0 +1,48 @@
+* Analog Devices adv7343 video encoder
+
+The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP
+package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite
+(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard
+definition (SD), enhanced definition (ED), or high definition (HD) video
+formats.
+
+Required Properties :
+- compatible: Must be "adi,adv7343"
+
+Optional Properties :
+- adi,power-mode-sleep-mode: on enable the current consumption is reduced to
+			      micro ampere level. All DACs and the internal PLL
+			      circuit are disabled.
+- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
+			   internal PLL 1 circuit to be powered down and the
+			   oversampling to be switched off.
+- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6,
+			      0 = OFF and 1 = ON, Default value when this
+			      property is not specified is <0 0 0 0 0 0>.
+- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF
+				 and 1 = ON, Default value when this property is
+				 not specified is <0 0>.
+
+Example:
+
+i2c0@1c22000 {
+	...
+	...
+
+	adv7343@2a {
+		compatible = "adi,adv7343";
+		reg = <0x2a>;
+
+		port {
+			adv7343_1: endpoint {
+					adi,power-mode-sleep-mode;
+					adi,power-mode-pll-ctrl;
+					/* Use DAC1..3, DAC6 */
+					adi,dac-enable = <1 1 1 0 0 1>;
+					/* Use SD DAC output 1 */
+					adi,sd-dac-enable = <1 0>;
+			};
+		};
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt
new file mode 100644
index 000000000..54d1d3bc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt
@@ -0,0 +1,95 @@
+* Analog Devices ADV748X video decoder with HDMI receiver
+
+The ADV7481 and ADV7482 are multi format video decoders with an integrated
+HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB
+from three input sources HDMI, analog and TTL.
+
+Required Properties:
+
+  - compatible: Must contain one of the following
+    - "adi,adv7481" for the ADV7481
+    - "adi,adv7482" for the ADV7482
+
+  - reg: I2C slave address
+
+Optional Properties:
+
+  - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or
+		     "intrq3". All interrupts are optional. The "intrq3" interrupt
+		     is only available on the adv7481
+  - interrupts: Specify the interrupt lines for the ADV748x
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+	  Name		Type		Port
+	---------------------------------------
+	  AIN0		sink		0
+	  AIN1		sink		1
+	  AIN2		sink		2
+	  AIN3		sink		3
+	  AIN4		sink		4
+	  AIN5		sink		5
+	  AIN6		sink		6
+	  AIN7		sink		7
+	  HDMI		sink		8
+	  TTL		sink		9
+	  TXA		source		10
+	  TXB		source		11
+
+The digital output port nodes must contain at least one endpoint.
+
+Ports are optional if they are not connected to anything at the hardware level.
+
+Example:
+
+	video-receiver@70 {
+		compatible = "adi,adv7482";
+		reg = <0x70>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gpio6>;
+		interrupt-names = "intrq1", "intrq2";
+		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
+			     <31 IRQ_TYPE_LEVEL_LOW>;
+
+		port@7 {
+			reg = <7>;
+
+			adv7482_ain7: endpoint {
+				remote-endpoint = <&cvbs_in>;
+			};
+		};
+
+		port@8 {
+			reg = <8>;
+
+			adv7482_hdmi: endpoint {
+				remote-endpoint = <&hdmi_in>;
+			};
+		};
+
+		port@a {
+			reg = <10>;
+
+			adv7482_txa: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&csi40_in>;
+			};
+		};
+
+		port@b {
+			reg = <11>;
+
+			adv7482_txb: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1>;
+				remote-endpoint = <&csi20_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
new file mode 100644
index 000000000..dcf57e7c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -0,0 +1,88 @@
+* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
+
+The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+similar to the 7611 but has 2 HDMI inputs.
+
+These device tree bindings support the ADV7611/12 only at the moment.
+
+Required Properties:
+
+  - compatible: Must contain one of the following
+    - "adi,adv7611" for the ADV7611
+    - "adi,adv7612" for the ADV7612
+
+  - reg: I2C slave addresses
+    The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
+    main I2C ports. Each map has it own I2C address and acts as a standard
+    slave device on the I2C bus. The main address is mandatory, others are
+    optional and revert to defaults if not specified.
+
+  - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
+    detection pins, one per HDMI input. The active flag indicates the GPIO
+    level that enables hot-plug detection.
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+  Port			ADV7611    ADV7612
+------------------------------------------------------------
+  HDMI			0             0, 1
+  Digital output	1                2
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties:
+
+  - reset-gpios: Reference to the GPIO connected to the device's reset pin.
+  - default-input: Select which input is selected after reset.
+  - reg-names : Names of maps with programmable addresses.
+		It can contain any map needing a non-default address.
+		Possible maps names are :
+		  "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
+		  "rep", "edid", "hdmi", "test", "cp", "vdp"
+
+Optional Endpoint Properties:
+
+  The following three properties are defined in video-interfaces.txt and are
+  valid for source endpoints only.
+
+  - hsync-active: Horizontal synchronization polarity. Defaults to active low.
+  - vsync-active: Vertical synchronization polarity. Defaults to active low.
+  - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
+
+  If none of hsync-active, vsync-active and pclk-sample is specified the
+  endpoint will use embedded BT.656 synchronization.
+
+Example:
+
+	hdmi_receiver@4c {
+		compatible = "adi,adv7611";
+		/*
+		 * The edid page will be accessible @ 0x66 on the I2C bus. All
+		 * other maps will retain their default addresses.
+		 */
+		reg = <0x4c>, <0x66>;
+		reg-names "main", "edid";
+
+		reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+		hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		default-input = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+		port@1 {
+			reg = <1>;
+			hdmi_in: endpoint {
+				remote-endpoint = <&ccdc_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ak7375.txt b/Documentation/devicetree/bindings/media/i2c/ak7375.txt
new file mode 100644
index 000000000..aa3e24b41
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ak7375.txt
@@ -0,0 +1,8 @@
+Asahi Kasei Microdevices AK7375 voice coil lens driver
+
+AK7375 is a camera voice coil lens.
+
+Mandatory properties:
+
+- compatible: "asahi-kasei,ak7375"
+- reg: I2C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt
new file mode 100644
index 000000000..bd896e9f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt
@@ -0,0 +1,46 @@
+* Aptina MT9V111 CMOS sensor
+----------------------------
+
+The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
+based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP).
+
+The sensor has an active pixel array of 640x480 pixels and can output a number
+of image resolution and formats controllable through a simple two-wires
+interface.
+
+Required properties:
+--------------------
+
+- compatible: shall be "aptina,mt9v111".
+- clocks: reference to the system clock input provider.
+
+Optional properties:
+--------------------
+
+- enable-gpios: output enable signal, pin name "OE#". Active low.
+- standby-gpios: low power state control signal, pin name "STANDBY".
+  Active high.
+- reset-gpios: chip reset signal, pin name "RESET#". Active low.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+--------
+
+        &i2c1 {
+                camera@48 {
+                        compatible = "aptina,mt9v111";
+                        reg = <0x48>;
+
+                        clocks = <&camera_clk>;
+
+                        port {
+                                mt9v111_out: endpoint {
+                                        remote-endpoint = <&ceu_in>;
+                                };
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt
new file mode 100644
index 000000000..b88dcdd41
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt
@@ -0,0 +1,9 @@
+Dongwoon Anatech DW9714 camera voice coil lens driver
+
+DW9174 is a 10-bit DAC with current sink capability. It is intended
+for driving voice coil lenses in camera modules.
+
+Mandatory properties:
+
+- compatible: "dongwoon,dw9714"
+- reg: I²C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt
new file mode 100644
index 000000000..c4701f1ea
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt
@@ -0,0 +1,9 @@
+Dongwoon Anatech DW9807 voice coil lens driver
+
+DW9807 is a 10-bit DAC with current sink capability. It is intended for
+controlling voice coil lenses.
+
+Mandatory properties:
+
+- compatible: "dongwoon,dw9807-vcm"
+- reg: I2C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/imx274.txt b/Documentation/devicetree/bindings/media/i2c/imx274.txt
new file mode 100644
index 000000000..80f2e8956
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx274.txt
@@ -0,0 +1,33 @@
+* Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor
+
+The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 3864H x 2202V. It is programmable through I2C
+interface. The I2C address is fixed to 0x1a as per sensor data sheet.
+Image data is sent through MIPI CSI-2, which is configured as 4 lanes
+at 1440 Mbps.
+
+
+Required Properties:
+- compatible: value should be "sony,imx274" for imx274 sensor
+- reg: I2C bus address of the device
+
+Optional Properties:
+- reset-gpios: Sensor reset GPIO
+
+The imx274 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+	sensor@1a {
+		compatible = "sony,imx274";
+		reg = <0x1a>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio_sensor 0 0>;
+		port {
+			sensor_out: endpoint {
+				remote-endpoint = <&csiss_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt
new file mode 100644
index 000000000..02b4e9cd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt
@@ -0,0 +1,59 @@
+Maxim Integrated MAX2175 RF to Bits tuner
+-----------------------------------------
+
+The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with
+RF to Bits® front-end designed for software-defined radio solutions.
+
+Required properties:
+--------------------
+- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner.
+- clocks: clock specifier.
+- port: child port node corresponding to the I2S output, in accordance with
+	the video interface bindings defined in
+	Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+	node must contain at least one endpoint.
+
+Optional properties:
+--------------------
+- maxim,master	      : phandle to the master tuner if it is a slave. This
+			is used to define two tuners in diversity mode
+			(1 master, 1 slave). By default each tuner is an
+			individual master.
+- maxim,refout-load   : load capacitance value (in picofarads) on reference
+			output drive level. The possible load values are:
+			 0 (default - refout disabled)
+			10
+			20
+			30
+			40
+			60
+			70
+- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used
+			in this hardware for AM antenna input.
+
+Example:
+--------
+
+Board specific DTS file
+
+/* Fixed XTAL clock node */
+maxim_xtal: clock {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <36864000>;
+};
+
+/* A tuner device instance under i2c bus */
+max2175_0: tuner@60 {
+	compatible = "maxim,max2175";
+	reg = <0x60>;
+	clocks = <&maxim_xtal>;
+	maxim,refout-load = <10>;
+
+	port {
+		max2175_0_ep: endpoint {
+			remote-endpoint = <&slave_rx_device>;
+		};
+	};
+
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
new file mode 100644
index 000000000..6b910036b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
@@ -0,0 +1,32 @@
+Micron 1.3Mp CMOS Digital Image Sensor
+
+The Micron MT9M111 is a CMOS active pixel digital image sensor with an active
+array size of 1280H x 1024V. It is programmable through a simple two-wire serial
+interface.
+
+Required Properties:
+- compatible: value should be "micron,mt9m111"
+- clocks: reference to the master clock.
+- clock-names: shall be "mclk".
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c_master {
+		mt9m111@5d {
+			compatible = "micron,mt9m111";
+			reg = <0x5d>;
+			clocks = <&mclk>;
+			clock-names = "mclk";
+
+			remote = <&pxa_camera>;
+			port {
+				mt9m111_1: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&pxa_camera>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
new file mode 100644
index 000000000..cb60443ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
@@ -0,0 +1,40 @@
+* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor
+
+The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+- compatible: value should be either one among the following
+	(a) "aptina,mt9p031" for mt9p031 sensor
+	(b) "aptina,mt9p031m" for mt9p031m sensor
+
+- input-clock-frequency: Input clock frequency.
+
+- pixel-clock-frequency: Pixel clock frequency.
+
+Optional Properties:
+- reset-gpios: Chip reset GPIO
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		mt9p031@5d {
+			compatible = "aptina,mt9p031";
+			reg = <0x5d>;
+			reset-gpios = <&gpio3 30 0>;
+
+			port {
+				mt9p031_1: endpoint {
+					input-clock-frequency = <6000000>;
+					pixel-clock-frequency = <96000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
new file mode 100644
index 000000000..100f0ae43
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
@@ -0,0 +1,41 @@
+* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor
+
+The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with
+an active array size of 752H x 480V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+
+- compatible: value should be either one among the following
+	(a) "aptina,mt9v022" for MT9V022 color sensor
+	(b) "aptina,mt9v022m" for MT9V022 monochrome sensor
+	(c) "aptina,mt9v024" for MT9V024 color sensor
+	(d) "aptina,mt9v024m" for MT9V024 monochrome sensor
+	(e) "aptina,mt9v032" for MT9V032 color sensor
+	(f) "aptina,mt9v032m" for MT9V032 monochrome sensor
+	(g) "aptina,mt9v034" for MT9V034 color sensor
+	(h) "aptina,mt9v034m" for MT9V034 monochrome sensor
+
+Optional Properties:
+
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+	expressed as a 64-bit big-endian integer.
+- reset-gpios: GPIO handle which is connected to the reset pin of the chip.
+- standby-gpios: GPIO handle which is connected to the standby pin of the chip.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	mt9v032@5c {
+		compatible = "aptina,mt9v032";
+		reg = <0x5c>;
+
+		port {
+			mt9v032_out: endpoint {
+				link-frequencies = /bits/ 64
+					<13000000 26600000 27000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt
new file mode 100644
index 000000000..8ee7c7972
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt
@@ -0,0 +1,68 @@
+SMIA/SMIA++ sensor
+
+SMIA (Standard Mobile Imaging Architecture) is an image sensor standard
+defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension
+of that. These definitions are valid for both types of sensors.
+
+More detailed documentation can be found in
+Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+
+Mandatory properties
+--------------------
+
+- compatible: "nokia,smia"
+- reg: I2C address (0x10, or an alternative address)
+- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor
+  dependent).
+- clocks: External clock to the sensor
+- clock-frequency: Frequency of the external clock to the sensor
+- link-frequencies: List of allowed data link frequencies. An array of
+  64-bit elements.
+
+
+Optional properties
+-------------------
+
+- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given,
+  the NVM contents will not be read.
+- reset-gpios: XSHUTDOWN GPIO
+- flash-leds: See ../video-interfaces.txt
+- lens-focus: See ../video-interfaces.txt
+- rotation: Integer property; valid values are 0 (sensor mounted upright)
+	    and 180 (sensor mounted upside down). See
+	    ../video-interfaces.txt .
+
+
+Endpoint node mandatory properties
+----------------------------------
+
+- clock-lanes: <0>
+- data-lanes: <1..n>
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+
+Example
+-------
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	smiapp_1: camera@10 {
+		compatible = "nokia,smia";
+		reg = <0x10>;
+		reset-gpios = <&gpio3 20 0>;
+		vana-supply = <&vaux3>;
+		clocks = <&omap3_isp 0>;
+		clock-frequency = <9600000>;
+		nokia,nvm-size = <512>; /* 8 * 64 */
+		link-frequencies = /bits/ 64 <199200000 210000000 499200000>;
+		port {
+			smiapp_1_1: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi2a_ep>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
new file mode 100644
index 000000000..989ce6cb6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
@@ -0,0 +1,41 @@
+* Omnivision OV2640 CMOS sensor
+
+The Omnivision OV2640 sensor supports multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB
+output formats.
+
+Required Properties:
+- compatible: should be "ovti,ov2640"
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+
+Optional Properties:
+- resetb-gpios: reference to the GPIO connected to the resetb pin, if any.
+- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov2640: camera@30 {
+			compatible = "ovti,ov2640";
+			reg = <0x30>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+			resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+			pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+			clocks = <&pck0>;
+			clock-names = "xvclk";
+			assigned-clocks = <&pck0>;
+			assigned-clock-rates = <25000000>;
+
+			port {
+				ov2640_0: endpoint {
+					remote-endpoint = <&isi_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
new file mode 100644
index 000000000..cabc7d827
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
@@ -0,0 +1,38 @@
+* OV2659 1/5-Inch 2Mp SOC Camera
+
+The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of
+1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports
+multiple resolutions output, such as UXGA, SVGA, 720p. It also can support
+YUV422, RGB565/555 or raw RGB output formats.
+
+Required Properties:
+- compatible: Must be "ovti,ov2659"
+- reg: I2C slave address
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- link-frequencies: target pixel clock frequency.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		 ov2659@30 {
+			compatible = "ovti,ov2659";
+			reg = <0x30>;
+
+			clocks = <&clk_ov2659 0>;
+			clock-names = "xvclk";
+
+			port {
+				ov2659_0: endpoint {
+					remote-endpoint = <&vpfe_ep>;
+					link-frequencies = /bits/ 64 <70000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
new file mode 100644
index 000000000..11e925ed9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
@@ -0,0 +1,46 @@
+* Omnivision OV2680 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov2680".
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- DOVDD-supply: Digital I/O voltage supply.
+- DVDD-supply: Digital core voltage supply.
+- AVDD-supply: Analog voltage supply.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
+               if any. This is an active low signal to the OV2680.
+
+The device node must contain one 'port' child node for its digital output
+video port, and this port must have a single endpoint in accordance with
+ the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
+- data-lanes: should be set to <1> (one CSI-2 lane supported).
+
+Example:
+
+&i2c2 {
+	ov2680: camera-sensor@36 {
+		compatible = "ovti,ov2680";
+		reg = <0x36>;
+		clocks = <&osc>;
+		clock-names = "xvclk";
+		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		DOVDD-supply = <&sw2_reg>;
+		DVDD-supply = <&sw2_reg>;
+		AVDD-supply = <&reg_peri_3p15v>;
+
+		port {
+			ov2680_to_mipi: endpoint {
+				remote-endpoint = <&mipi_from_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2685.txt b/Documentation/devicetree/bindings/media/i2c/ov2685.txt
new file mode 100644
index 000000000..625c4a8c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2685.txt
@@ -0,0 +1,41 @@
+* Omnivision OV2685 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov2685"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.8 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1>".
+
+Example:
+&i2c7 {
+	ov2685: camera-sensor@3c {
+		compatible = "ovti,ov2685";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clk_24m_cam>;
+
+		clocks = <&cru SCLK_TESTCLKOUT1>;
+		clock-names = "xvclk";
+
+		avdd-supply = <&pp2800_cam>;
+		dovdd-supply = <&pp1800>;
+		dvdd-supply = <&pp1800>;
+		reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+
+		port {
+			ucam_out: endpoint {
+				remote-endpoint = <&mipi_in_ucam>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
new file mode 100644
index 000000000..c97c2f2da
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
@@ -0,0 +1,92 @@
+* Omnivision OV5640 MIPI CSI-2 / parallel sensor
+
+Required Properties:
+- compatible: should be "ovti,ov5640"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.5 volts
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+	       This is an active low signal to the OV5640.
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		   if any. This is an active high signal to the OV5640.
+- rotation: as defined in
+	    Documentation/devicetree/bindings/media/video-interfaces.txt,
+	    valid values are 0 (sensor mounted upright) and 180 (sensor
+	    mounted upside down).
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
+
+Endpoint node required properties for parallel connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- bus-width: shall be set to <8> for 8 bits parallel bus
+	     or <10> for 10 bits parallel bus
+- data-shift: shall be set to <2> for 8 bits parallel bus
+	      (lines 9:2 are used) or <0> for 10 bits parallel bus
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
+	       signal.
+
+Examples:
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+		rotation = <180>;
+
+		port {
+			/* MIPI CSI-2 bus endpoint */
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_from_ov5640>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clk_ext_camera>;
+		clock-names = "xclk";
+
+		port {
+			/* Parallel bus endpoint */
+			ov5640_to_parallel: endpoint {
+				remote-endpoint = <&parallel_from_ov5640>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <0>;
+				vsync-active = <0>;
+				pclk-sample = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
new file mode 100644
index 000000000..fd7aec9f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
@@ -0,0 +1,54 @@
+* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor
+
+The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a serial I2C
+interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov5645".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin PWDNB which is physically active low.
+- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
+  the hardware pin RESETB.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov5645: ov5645@78 {
+			compatible = "ovti,ov5645";
+			reg = <0x78>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_rear_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <23880000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov5645_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0 2>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
new file mode 100644
index 000000000..22e44945b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
@@ -0,0 +1,35 @@
+Omnivision OV5647 raw image sensor
+---------------------------------
+
+OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
+and CCI (I2C compatible) control bus.
+
+Required properties:
+
+- compatible		: "ovti,ov5647".
+- reg			: I2C slave address of the sensor.
+- clocks		: Reference to the xclk clock.
+
+The common video interfaces bindings (see video-interfaces.txt) should be
+used to specify link to the image data receiver. The OV5647 device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Endpoint node mandatory properties:
+
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+Example:
+
+	i2c@2000 {
+		...
+		ov: camera@36 {
+			compatible = "ovti,ov5647";
+			reg = <0x36>;
+			clocks = <&camera_clk>;
+			port {
+				camera_1: endpoint {
+					remote-endpoint = <&csi1_ep1>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5695.txt b/Documentation/devicetree/bindings/media/i2c/ov5695.txt
new file mode 100644
index 000000000..640a63717
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5695.txt
@@ -0,0 +1,41 @@
+* Omnivision OV5695 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov5695"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.2 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1 2>".
+
+Example:
+&i2c7 {
+	ov5695: camera-sensor@36 {
+		compatible = "ovti,ov5695";
+		reg = <0x36>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clk_24m_cam>;
+
+		clocks = <&cru SCLK_TESTCLKOUT1>;
+		clock-names = "xvclk";
+
+		avdd-supply = <&pp2800_cam>;
+		dovdd-supply = <&pp1800>;
+		dvdd-supply = <&pp1250_cam>;
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+
+		port {
+			wcam_out: endpoint {
+				remote-endpoint = <&mipi_in_wcam>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
new file mode 100644
index 000000000..8281151f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
@@ -0,0 +1,52 @@
+* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor
+
+The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor
+with an active array size of 640H x 480V. It is programmable through a serial
+I2C interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov7251".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin XSHUTDOWN which is physically active low.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node shall contain one 'port' child node with a single 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov7251: camera-sensor@60 {
+			compatible = "ovti,ov7251";
+			reg = <0x60>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_bw_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <24000000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov7251_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7670.txt b/Documentation/devicetree/bindings/media/i2c/ov7670.txt
new file mode 100644
index 000000000..2c972a56f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7670.txt
@@ -0,0 +1,55 @@
+* Omnivision OV7670 CMOS sensor
+
+The Omnivision OV7670 sensor supports multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB
+output formats.
+
+Required Properties:
+- compatible: should be "ovti,ov7670"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+
+Required Endpoint Properties:
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active is low.
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active is high.
+- ov7670,pclk-hb-disable: a boolean property to suppress pixel clock output
+  signal during horizontal blankings.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov7670: camera@21 {
+			compatible = "ovti,ov7670";
+			reg = <0x21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+			reset-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+			powerdown-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+			clocks = <&pck0>;
+			clock-names = "xclk";
+			assigned-clocks = <&pck0>;
+			assigned-clock-rates = <25000000>;
+
+			ov7670,pclk-hb-disable;
+
+			port {
+				ov7670_0: endpoint {
+					hsync-active = <0>;
+					vsync-active = <0>;
+
+					remote-endpoint = <&isi_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt
new file mode 100644
index 000000000..0b3ede5b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov772x.txt
@@ -0,0 +1,40 @@
+* Omnivision OV7720/OV7725 CMOS sensor
+
+The Omnivision OV7720/OV7725 sensor supports multiple resolutions output,
+such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can
+support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats.
+
+Required Properties:
+- compatible: shall be one of
+	"ovti,ov7720"
+	"ovti,ov7725"
+- clocks: reference to the xclk input clock.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the RSTB pin which is
+  active low, if any.
+- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is
+  active high, if any.
+
+The device node shall contain one 'port' child node with one child 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+&i2c0 {
+	ov772x: camera@21 {
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>;
+		clocks = <&xclk>;
+
+		port {
+			ov772x_0: endpoint {
+				remote-endpoint = <&vcap1_in0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
new file mode 100644
index 000000000..af781c3a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
@@ -0,0 +1,47 @@
+* Omnivision OV7740 CMOS image sensor
+
+The Omnivision OV7740 image sensor supports multiple output image
+size, such as VGA, and QVGA, CIF and any size smaller. It also
+supports the RAW RGB and YUV output formats.
+
+The common video interfaces bindings (see video-interfaces.txt) should
+be used to specify link to the image data receiver. The OV7740 device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Required Properties:
+- compatible:	"ovti,ov7740".
+- reg:		I2C slave address of the sensor.
+- clocks:	Reference to the xvclk input clock.
+- clock-names:	"xvclk".
+
+Optional Properties:
+- reset-gpios: Rreference to the GPIO connected to the reset_b pin,
+  if any. Active low with pull-ip resistor.
+- powerdown-gpios: Reference to the GPIO connected to the pwdn pin,
+  if any. Active high with pull-down resistor.
+
+Endpoint node mandatory properties:
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+Example:
+
+	i2c1: i2c@fc028000 {
+		ov7740: camera@21 {
+			compatible = "ovti,ov7740";
+			reg = <0x21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>;
+			clocks = <&isc>;
+			clock-names = "xvclk";
+			assigned-clocks = <&isc>;
+			assigned-clock-rates = <24000000>;
+			reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>;
+			powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>;
+
+			port {
+				ov7740_0: endpoint {
+					remote-endpoint = <&isc_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov9650.txt b/Documentation/devicetree/bindings/media/i2c/ov9650.txt
new file mode 100644
index 000000000..506dfc528
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov9650.txt
@@ -0,0 +1,36 @@
+* Omnivision OV9650/OV9652 CMOS sensor
+
+Required Properties:
+- compatible: shall be one of
+	"ovti,ov9650"
+	"ovti,ov9652"
+- clocks: reference to the xvclk input clock.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active is high.
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active is high.
+
+The device node shall contain one 'port' child node with one child 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+&i2c0 {
+	ov9650: camera@30 {
+		compatible = "ovti,ov9650";
+		reg = <0x30>;
+		reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_HIGH>;
+		powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_HIGH>;
+		clocks = <&xclk>;
+
+		port {
+			ov9650_0: endpoint {
+				remote-endpoint = <&vcap1_in0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt
new file mode 100644
index 000000000..4a3181a3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt
@@ -0,0 +1,19 @@
+* Panasonic AMG88xx
+
+The Panasonic family of AMG88xx Grid-Eye sensors allow recording
+8x8 10Hz video which consists of thermal datapoints
+
+Required Properties:
+ - compatible : Must be "panasonic,amg88xx"
+ - reg : i2c address of the device
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		amg88xx@69 {
+			compatible = "panasonic,amg88xx";
+			reg = <0x69>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/Documentation/devicetree/bindings/media/i2c/tc358743.txt
new file mode 100644
index 000000000..59102edcf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tc358743.txt
@@ -0,0 +1,48 @@
+* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge
+
+The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts
+a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C.
+
+Required Properties:
+
+- compatible: value should be "toshiba,tc358743"
+- clocks, clock-names: should contain a phandle link to the reference clock
+		       source, the clock input is named "refclk".
+
+Optional Properties:
+
+- reset-gpios: gpio phandle GPIO connected to the reset pin
+- interrupts: GPIO connected to the interrupt pin
+- data-lanes: should be <1 2 3 4> for four-lane operation,
+	      or <1 2> for two-lane operation
+- clock-lanes: should be <0>
+- clock-noncontinuous: Presence of this boolean property decides whether the
+		       MIPI CSI-2 clock is continuous or non-continuous.
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+		    expressed as a 64-bit big-endian integer. The frequency
+		    is half of the bps per lane due to DDR transmission.
+
+For further information on the MIPI CSI-2 endpoint node properties, see
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	tc358743@f {
+		compatible = "toshiba,tc358743";
+		reg = <0x0f>;
+		clocks = <&hdmi_osc>;
+		clock-names = "refclk";
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		port {
+			tc358743_out: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				data-lanes = <1 2 3 4>;
+				clock-lanes = <0>;
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <297000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
new file mode 100644
index 000000000..e76167999
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
@@ -0,0 +1,178 @@
+Device-Tree bindings for the NXP TDA1997x HDMI receiver
+
+The TDA19971/73 are HDMI video receivers.
+
+The TDA19971 Video port output pins can be used as follows:
+ - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
+ - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
+ - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
+ - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
+ - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
+ - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
+ - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The TDA19973 Video port output pins can be used as follows:
+ - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
+ - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
+ - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The Video port output pins are mapped via 4-bit 'pin groups' allowing
+for a variety of connection possibilities including swapping pin order within
+pin groups. The video_portcfg device-tree property consists of register mapping
+pairs which map a chip-specific VP output register to a 4-bit pin group. If
+the pin group needs to be bit-swapped you can use the *_S pin-group defines.
+
+Required Properties:
+ - compatible          :
+  - "nxp,tda19971" for the TDA19971
+  - "nxp,tda19973" for the TDA19973
+ - reg                 : I2C slave address
+ - interrupts          : The interrupt number
+ - DOVDD-supply        : Digital I/O supply
+ - DVDD-supply         : Digital Core supply
+ - AVDD-supply         : Analog supply
+ - nxp,vidout-portcfg  : array of pairs mapping VP output pins to pin groups.
+
+Optional Properties:
+ - nxp,audout-format   : DAI bus format: "i2s" or "spdif".
+ - nxp,audout-width    : width of audio output data bus (1-4).
+ - nxp,audout-layout   : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
+ - nxp,audout-mclk-fs  : Multiplication factor between stream rate and codec
+                         mclk.
+
+The port node shall contain one endpoint child node for its digital
+output video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Optional Endpoint Properties:
+  The following three properties are defined in video-interfaces.txt and
+  are valid for the output parallel bus endpoint:
+  - hsync-active: Horizontal synchronization polarity. Defaults to active high.
+  - vsync-active: Vertical synchronization polarity. Defaults to active high.
+  - data-active: Data polarity. Defaults to active high.
+
+Examples:
+ - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same pixclk cycle.
+		 */
+		nxp,vidout-portcfg =
+			/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same pixclk cycle.
+		 */
+		nxp,vidout-portcfg =
+			/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
+		 * 2 pixclk cycles.
+		 */
+		nxp,vidout-portcfg =
+			/* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
+			/* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
new file mode 100644
index 000000000..285f6ae7d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
@@ -0,0 +1,19 @@
+* Texas Instruments THS8200 video encoder
+
+The ths8200 device is a digital to analog converter used in DVD players, video
+recorders, set-top boxes.
+
+Required Properties :
+- compatible : value must be "ti,ths8200"
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		ths8200@5c {
+			compatible = "ti,ths8200";
+			reg = <0x5c>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
new file mode 100644
index 000000000..e80d5891b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
@@ -0,0 +1,55 @@
+Toshiba et8ek8 5MP sensor
+
+Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device
+
+More detailed documentation can be found in
+Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+
+Mandatory properties
+--------------------
+
+- compatible: "toshiba,et8ek8"
+- reg: I2C address (0x3e, or an alternative address)
+- vana-supply: Analogue voltage supply (VANA), 2.8 volts
+- clocks: External clock to the sensor
+- clock-frequency: Frequency of the external clock to the sensor. Camera
+  driver will set this frequency on the external clock. The clock frequency is
+  a pre-determined frequency known to be suitable to the board.
+- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor
+  is in hardware standby mode when the signal is in the low state.
+
+
+Optional properties
+-------------------
+
+- flash-leds: See ../video-interfaces.txt
+- lens-focus: See ../video-interfaces.txt
+
+
+Endpoint node mandatory properties
+----------------------------------
+
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+
+Example
+-------
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	cam1: camera@3e {
+		compatible = "toshiba,et8ek8";
+		reg = <0x3e>;
+		vana-supply = <&vaux4>;
+		clocks = <&isp 0>;
+		clock-frequency = <9600000>;
+		reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
+		port {
+			csi_cam1: endpoint {
+				remote-endpoint = <&csi_out1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
new file mode 100644
index 000000000..46752cc71
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
@@ -0,0 +1,44 @@
+* Texas Instruments TVP514x video decoder
+
+The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip
+digital video decoder that digitizes and decodes all popular baseband analog
+video formats into digital video component. The tvp514x decoder supports analog-
+to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
+conversion and decoding of NTSC, PAL and SECAM composite and S-video into
+component YCbCr.
+
+Required Properties :
+- compatible : value should be either one among the following
+	(a) "ti,tvp5146" for tvp5146 decoder.
+	(b) "ti,tvp5146m2" for tvp5146m2 decoder.
+	(c) "ti,tvp5147" for tvp5147 decoder.
+	(d) "ti,tvp5147m1" for tvp5147m1 decoder.
+
+- hsync-active: HSYNC Polarity configuration for endpoint.
+
+- vsync-active: VSYNC Polarity configuration for endpoint.
+
+- pclk-sample: Clock polarity of the endpoint.
+
+For further reading on port node refer to Documentation/devicetree/bindings/
+media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp514x@5c {
+			compatible = "ti,tvp5146";
+			reg = <0x5c>;
+
+			port {
+				tvp514x_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
new file mode 100644
index 000000000..8c0fc1a26
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -0,0 +1,45 @@
+* Texas Instruments TVP5150 and TVP5151 video decoders
+
+The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+Required Properties:
+- compatible: value must be "ti,tvp5150"
+- reg: I2C slave address
+
+Optional Properties:
+- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
+- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Endpoint Properties for parallel synchronization:
+
+- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
+- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
+- field-even-active: field signal level during the even field data
+  transmission. Must be <0>.
+
+If none of hsync-active, vsync-active and field-even-active is specified,
+the endpoint is assumed to use embedded BT.656 synchronization.
+
+Example:
+
+&i2c2 {
+	...
+	tvp5150@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+
+		port {
+			tvp5150_1: endpoint {
+				remote-endpoint = <&ccdc_ep>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
new file mode 100644
index 000000000..5f28b5d9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
@@ -0,0 +1,53 @@
+* Texas Instruments TV7002 video decoder
+
+The TVP7002 device supports digitizing of video and graphics signal in RGB and
+YPbPr color space.
+
+Required Properties :
+- compatible : Must be "ti,tvp7002"
+
+Optional Properties:
+- hsync-active: HSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- vsync-active: VSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- pclk-sample: Clock polarity of the bus. Default value when this property is
+  not specified is <0>.
+
+- sync-on-green-active: Active state of Sync-on-green signal property of the
+  endpoint.
+  0 = Normal Operation (Active Low, Default)
+  1 = Inverted operation
+
+- field-even-active: Active-high Field ID output polarity control of the bus.
+  Under normal operation, the field ID output is set to logic 1 for an odd field
+  (field 1) and set to logic 0 for an even field (field 0).
+  0 = Normal Operation (Active Low, Default)
+  1 = FID output polarity inverted
+
+For further reading of port node refer Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp7002@5c {
+			compatible = "ti,tvp7002";
+			reg = <0x5c>;
+
+			port {
+				tvp7002_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+					sync-on-green-active = <1>;
+					field-even-active = <0>;
+				};
+			};
+		};
+		...
+	};