Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 414 insertions, 0 deletions

diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
new file mode 100644
index 000000000..048f15e8c
--- /dev/null
+++ b/arch/arm/mach-u300/core.c
@@ -0,0 +1,414 @@
+/*
+ *
+ * arch/arm/mach-u300/core.c
+ *
+ *
+ * Copyright (C) 2007-2012 ST-Ericsson SA
+ * License terms: GNU General Public License (GPL) version 2
+ * Core platform support, IRQ handling and device definitions.
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/kernel.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/platform_data/clk-u300.h>
+#include <linux/irqchip.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/clocksource.h>
+#include <linux/clk.h>
+
+#include <asm/mach/map.h>
+#include <asm/mach/arch.h>
+
+/*
+ * These are the large blocks of memory allocated for I/O.
+ * the defines are used for setting up the I/O memory mapping.
+ */
+
+/* NAND Flash CS0 */
+#define U300_NAND_CS0_PHYS_BASE		0x80000000
+/* NFIF */
+#define U300_NAND_IF_PHYS_BASE		0x9f800000
+/* ALE, CLE offset for FSMC NAND */
+#define PLAT_NAND_CLE			(1 << 16)
+#define PLAT_NAND_ALE			(1 << 17)
+/* AHB Peripherals */
+#define U300_AHB_PER_PHYS_BASE		0xa0000000
+#define U300_AHB_PER_VIRT_BASE		0xff010000
+/* FAST Peripherals */
+#define U300_FAST_PER_PHYS_BASE		0xc0000000
+#define U300_FAST_PER_VIRT_BASE		0xff020000
+/* SLOW Peripherals */
+#define U300_SLOW_PER_PHYS_BASE		0xc0010000
+#define U300_SLOW_PER_VIRT_BASE		0xff000000
+/* Boot ROM */
+#define U300_BOOTROM_PHYS_BASE		0xffff0000
+#define U300_BOOTROM_VIRT_BASE		0xffff0000
+/* SEMI config base */
+#define U300_SEMI_CONFIG_BASE		0x2FFE0000
+
+/*
+ * AHB peripherals
+ */
+
+/* AHB Peripherals Bridge Controller */
+#define U300_AHB_BRIDGE_BASE		(U300_AHB_PER_PHYS_BASE+0x0000)
+/* Vectored Interrupt Controller 0, servicing 32 interrupts */
+#define U300_INTCON0_BASE		(U300_AHB_PER_PHYS_BASE+0x1000)
+#define U300_INTCON0_VBASE		IOMEM(U300_AHB_PER_VIRT_BASE+0x1000)
+/* Vectored Interrupt Controller 1, servicing 32 interrupts */
+#define U300_INTCON1_BASE		(U300_AHB_PER_PHYS_BASE+0x2000)
+#define U300_INTCON1_VBASE		IOMEM(U300_AHB_PER_VIRT_BASE+0x2000)
+/* Memory Stick Pro (MSPRO) controller */
+#define U300_MSPRO_BASE			(U300_AHB_PER_PHYS_BASE+0x3000)
+/* EMIF Configuration Area */
+#define U300_EMIF_CFG_BASE		(U300_AHB_PER_PHYS_BASE+0x4000)
+
+/*
+ * FAST peripherals
+ */
+
+/* FAST bridge control */
+#define U300_FAST_BRIDGE_BASE		(U300_FAST_PER_PHYS_BASE+0x0000)
+/* MMC/SD controller */
+#define U300_MMCSD_BASE			(U300_FAST_PER_PHYS_BASE+0x1000)
+/* PCM I2S0 controller */
+#define U300_PCM_I2S0_BASE		(U300_FAST_PER_PHYS_BASE+0x2000)
+/* PCM I2S1 controller */
+#define U300_PCM_I2S1_BASE		(U300_FAST_PER_PHYS_BASE+0x3000)
+/* I2C0 controller */
+#define U300_I2C0_BASE			(U300_FAST_PER_PHYS_BASE+0x4000)
+/* I2C1 controller */
+#define U300_I2C1_BASE			(U300_FAST_PER_PHYS_BASE+0x5000)
+/* SPI controller */
+#define U300_SPI_BASE			(U300_FAST_PER_PHYS_BASE+0x6000)
+/* Fast UART1 on U335 only */
+#define U300_UART1_BASE			(U300_FAST_PER_PHYS_BASE+0x7000)
+
+/*
+ * SLOW peripherals
+ */
+
+/* SLOW bridge control */
+#define U300_SLOW_BRIDGE_BASE		(U300_SLOW_PER_PHYS_BASE)
+/* SYSCON */
+#define U300_SYSCON_BASE		(U300_SLOW_PER_PHYS_BASE+0x1000)
+#define U300_SYSCON_VBASE		IOMEM(U300_SLOW_PER_VIRT_BASE+0x1000)
+/* Watchdog */
+#define U300_WDOG_BASE			(U300_SLOW_PER_PHYS_BASE+0x2000)
+/* UART0 */
+#define U300_UART0_BASE			(U300_SLOW_PER_PHYS_BASE+0x3000)
+/* APP side special timer */
+#define U300_TIMER_APP_BASE		(U300_SLOW_PER_PHYS_BASE+0x4000)
+#define U300_TIMER_APP_VBASE		IOMEM(U300_SLOW_PER_VIRT_BASE+0x4000)
+/* Keypad */
+#define U300_KEYPAD_BASE		(U300_SLOW_PER_PHYS_BASE+0x5000)
+/* GPIO */
+#define U300_GPIO_BASE			(U300_SLOW_PER_PHYS_BASE+0x6000)
+/* RTC */
+#define U300_RTC_BASE			(U300_SLOW_PER_PHYS_BASE+0x7000)
+/* Bus tracer */
+#define U300_BUSTR_BASE			(U300_SLOW_PER_PHYS_BASE+0x8000)
+/* Event handler (hardware queue) */
+#define U300_EVHIST_BASE		(U300_SLOW_PER_PHYS_BASE+0x9000)
+/* Genric Timer */
+#define U300_TIMER_BASE			(U300_SLOW_PER_PHYS_BASE+0xa000)
+/* PPM */
+#define U300_PPM_BASE			(U300_SLOW_PER_PHYS_BASE+0xb000)
+
+/*
+ * REST peripherals
+ */
+
+/* ISP (image signal processor) */
+#define U300_ISP_BASE			(0xA0008000)
+/* DMA Controller base */
+#define U300_DMAC_BASE			(0xC0020000)
+/* MSL Base */
+#define U300_MSL_BASE			(0xc0022000)
+/* APEX Base */
+#define U300_APEX_BASE			(0xc0030000)
+/* Video Encoder Base */
+#define U300_VIDEOENC_BASE		(0xc0080000)
+/* XGAM Base */
+#define U300_XGAM_BASE			(0xd0000000)
+
+/*
+ * SYSCON addresses applicable to the core machine.
+ */
+
+/* Chip ID register 16bit (R/-) */
+#define U300_SYSCON_CIDR					(0x400)
+/* SMCR */
+#define U300_SYSCON_SMCR					(0x4d0)
+#define U300_SYSCON_SMCR_FIELD_MASK				(0x000e)
+#define U300_SYSCON_SMCR_SEMI_SREFACK_IND			(0x0008)
+#define U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE			(0x0004)
+#define U300_SYSCON_SMCR_SEMI_EXT_BOOT_MODE_ENABLE		(0x0002)
+/* CPU_SW_DBGEN Software Debug Enable 16bit (R/W) */
+#define U300_SYSCON_CSDR					(0x4f0)
+#define U300_SYSCON_CSDR_SW_DEBUG_ENABLE			(0x0001)
+/* PRINT_CONTROL Print Control 16bit (R/-) */
+#define U300_SYSCON_PCR						(0x4f8)
+#define U300_SYSCON_PCR_SERV_IND				(0x0001)
+/* BOOT_CONTROL 16bit (R/-) */
+#define U300_SYSCON_BCR						(0x4fc)
+#define U300_SYSCON_BCR_ACC_CPU_SUBSYS_VINITHI_IND		(0x0400)
+#define U300_SYSCON_BCR_APP_CPU_SUBSYS_VINITHI_IND		(0x0200)
+#define U300_SYSCON_BCR_EXTRA_BOOT_OPTION_MASK			(0x01FC)
+#define U300_SYSCON_BCR_APP_BOOT_SERV_MASK			(0x0003)
+
+static void __iomem *syscon_base;
+
+/*
+ * Static I/O mappings that are needed for booting the U300 platforms. The
+ * only things we need are the areas where we find the timer, syscon and
+ * intcon, since the remaining device drivers will map their own memory
+ * physical to virtual as the need arise.
+ */
+static struct map_desc u300_io_desc[] __initdata = {
+	{
+		.virtual	= U300_SLOW_PER_VIRT_BASE,
+		.pfn		= __phys_to_pfn(U300_SLOW_PER_PHYS_BASE),
+		.length		= SZ_64K,
+		.type		= MT_DEVICE,
+	},
+	{
+		.virtual	= U300_AHB_PER_VIRT_BASE,
+		.pfn		= __phys_to_pfn(U300_AHB_PER_PHYS_BASE),
+		.length		= SZ_32K,
+		.type		= MT_DEVICE,
+	},
+	{
+		.virtual	= U300_FAST_PER_VIRT_BASE,
+		.pfn		= __phys_to_pfn(U300_FAST_PER_PHYS_BASE),
+		.length		= SZ_32K,
+		.type		= MT_DEVICE,
+	},
+};
+
+static void __init u300_map_io(void)
+{
+	iotable_init(u300_io_desc, ARRAY_SIZE(u300_io_desc));
+}
+
+static unsigned long pin_pullup_conf[] = {
+	PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 1),
+};
+
+static unsigned long pin_highz_conf[] = {
+	PIN_CONF_PACKED(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0),
+};
+
+/* Pin control settings */
+static struct pinctrl_map __initdata u300_pinmux_map[] = {
+	/* anonymous maps for chip power and EMIFs */
+	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "power"),
+	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif0"),
+	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif1"),
+	/* per-device maps for MMC/SD, SPI and UART */
+	PIN_MAP_MUX_GROUP_DEFAULT("mmci",  "pinctrl-u300", NULL, "mmc0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("pl022", "pinctrl-u300", NULL, "spi0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-u300", NULL, "uart0"),
+	/* This pin is used for clock return rather than GPIO */
+	PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO APP GPIO 11",
+				    pin_pullup_conf),
+	/* This pin is used for card detect */
+	PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO MS INS",
+				    pin_highz_conf),
+};
+
+struct db_chip {
+	u16 chipid;
+	const char *name;
+};
+
+/*
+ * This is a list of the Digital Baseband chips used in the U300 platform.
+ */
+static struct db_chip db_chips[] __initdata = {
+	{
+		.chipid = 0xb800,
+		.name = "DB3000",
+	},
+	{
+		.chipid = 0xc000,
+		.name = "DB3100",
+	},
+	{
+		.chipid = 0xc800,
+		.name = "DB3150",
+	},
+	{
+		.chipid = 0xd800,
+		.name = "DB3200",
+	},
+	{
+		.chipid = 0xe000,
+		.name = "DB3250",
+	},
+	{
+		.chipid = 0xe800,
+		.name = "DB3210",
+	},
+	{
+		.chipid = 0xf000,
+		.name = "DB3350 P1x",
+	},
+	{
+		.chipid = 0xf100,
+		.name = "DB3350 P2x",
+	},
+	{
+		.chipid = 0x0000, /* List terminator */
+		.name = NULL,
+	}
+};
+
+static void __init u300_init_check_chip(void)
+{
+
+	u16 val;
+	struct db_chip *chip;
+	const char *chipname;
+	const char unknown[] = "UNKNOWN";
+
+	/* Read out and print chip ID */
+	val = readw(syscon_base + U300_SYSCON_CIDR);
+	/* This is in funky bigendian order... */
+	val = (val & 0xFFU) << 8 | (val >> 8);
+	chip = db_chips;
+	chipname = unknown;
+
+	for ( ; chip->chipid; chip++) {
+		if (chip->chipid == (val & 0xFF00U)) {
+			chipname = chip->name;
+			break;
+		}
+	}
+	printk(KERN_INFO "Initializing U300 system on %s baseband chip " \
+	       "(chip ID 0x%04x)\n", chipname, val);
+
+	if ((val & 0xFF00U) != 0xf000 && (val & 0xFF00U) != 0xf100) {
+		printk(KERN_ERR "Platform configured for BS335 " \
+		       " with DB3350 but %s detected, expect problems!",
+		       chipname);
+	}
+}
+
+/* Forward declare this function from the watchdog */
+void coh901327_watchdog_reset(void);
+
+static void u300_restart(enum reboot_mode mode, const char *cmd)
+{
+	switch (mode) {
+	case REBOOT_SOFT:
+	case REBOOT_HARD:
+#ifdef CONFIG_COH901327_WATCHDOG
+		coh901327_watchdog_reset();
+#endif
+		break;
+	default:
+		/* Do nothing */
+		break;
+	}
+	/* Wait for system do die/reset. */
+	while (1);
+}
+
+/* These are mostly to get the right device names for the clock lookups */
+static struct of_dev_auxdata u300_auxdata_lookup[] __initdata = {
+	OF_DEV_AUXDATA("stericsson,pinctrl-u300", U300_SYSCON_BASE,
+		"pinctrl-u300", NULL),
+	OF_DEV_AUXDATA("stericsson,gpio-coh901", U300_GPIO_BASE,
+		"u300-gpio", NULL),
+	OF_DEV_AUXDATA("stericsson,coh901327", U300_WDOG_BASE,
+		"coh901327_wdog", NULL),
+	OF_DEV_AUXDATA("stericsson,coh901331", U300_RTC_BASE,
+		"rtc-coh901331", NULL),
+	OF_DEV_AUXDATA("stericsson,coh901318", U300_DMAC_BASE,
+		"coh901318", NULL),
+	OF_DEV_AUXDATA("stericsson,fsmc-nand", U300_NAND_IF_PHYS_BASE,
+		"fsmc-nand", NULL),
+	OF_DEV_AUXDATA("arm,primecell", U300_UART0_BASE,
+		"uart0", NULL),
+	OF_DEV_AUXDATA("arm,primecell", U300_UART1_BASE,
+		"uart1", NULL),
+	OF_DEV_AUXDATA("arm,primecell", U300_SPI_BASE,
+		"pl022", NULL),
+	OF_DEV_AUXDATA("st,ddci2c", U300_I2C0_BASE,
+		"stu300.0", NULL),
+	OF_DEV_AUXDATA("st,ddci2c", U300_I2C1_BASE,
+		"stu300.1", NULL),
+	OF_DEV_AUXDATA("arm,primecell", U300_MMCSD_BASE,
+		"mmci", NULL),
+	{ /* sentinel */ },
+};
+
+static void __init u300_init_irq_dt(void)
+{
+	struct device_node *syscon;
+	struct clk *clk;
+
+	syscon = of_find_node_by_path("/syscon@c0011000");
+	if (!syscon) {
+		pr_crit("could not find syscon node\n");
+		return;
+	}
+	syscon_base = of_iomap(syscon, 0);
+	if (!syscon_base) {
+		pr_crit("could not remap syscon\n");
+		return;
+	}
+	/* initialize clocking early, we want to clock the INTCON */
+	u300_clk_init(syscon_base);
+
+	/* Bootstrap EMIF and SEMI clocks */
+	clk = clk_get_sys("pl172", NULL);
+	BUG_ON(IS_ERR(clk));
+	clk_prepare_enable(clk);
+	clk = clk_get_sys("semi", NULL);
+	BUG_ON(IS_ERR(clk));
+	clk_prepare_enable(clk);
+
+	/* Clock the interrupt controller */
+	clk = clk_get_sys("intcon", NULL);
+	BUG_ON(IS_ERR(clk));
+	clk_prepare_enable(clk);
+
+	irqchip_init();
+}
+
+static void __init u300_init_machine_dt(void)
+{
+	u16 val;
+
+	/* Check what platform we run and print some status information */
+	u300_init_check_chip();
+
+	/* Initialize pinmuxing */
+	pinctrl_register_mappings(u300_pinmux_map,
+				  ARRAY_SIZE(u300_pinmux_map));
+
+	of_platform_default_populate(NULL, u300_auxdata_lookup, NULL);
+
+	/* Enable SEMI self refresh */
+	val = readw(syscon_base + U300_SYSCON_SMCR) |
+		U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE;
+	writew(val, syscon_base + U300_SYSCON_SMCR);
+}
+
+static const char * u300_board_compat[] = {
+	"stericsson,u300",
+	NULL,
+};
+
+DT_MACHINE_START(U300_DT, "U300 S335/B335 (Device Tree)")
+	.map_io		= u300_map_io,
+	.init_irq	= u300_init_irq_dt,
+	.init_time	= timer_probe,
+	.init_machine	= u300_init_machine_dt,
+	.restart	= u300_restart,
+	.dt_compat      = u300_board_compat,
+MACHINE_END