Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 621 insertions, 0 deletions

diff --git a/arch/mips/alchemy/devboards/db1550.c b/arch/mips/alchemy/devboards/db1550.c
new file mode 100644
index 000000000..7d3dfaa10
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1550.c
@@ -0,0 +1,621 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Alchemy Db1550/Pb1550 board support
+ *
+ * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-au1x00/au1550nd.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+static void __init db1550_hw_setup(void)
+{
+	void __iomem *base;
+	unsigned long v;
+
+	/* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line)
+	 * as well as PSC1_SYNC for AC97 on PB1550.
+	 */
+	v = alchemy_rdsys(AU1000_SYS_PINFUNC);
+	alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC);
+
+	/* reset the AC97 codec now, the reset time in the psc-ac97 driver
+	 * is apparently too short although it's ridiculous as it is.
+	 */
+	base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
+	__raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
+		     base + PSC_SEL_OFFSET);
+	__raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
+	wmb();
+	__raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
+	wmb();
+}
+
+int __init db1550_board_setup(void)
+{
+	unsigned short whoami;
+
+	bcsr_init(DB1550_BCSR_PHYS_ADDR,
+		  DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
+
+	whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */
+	switch (BCSR_WHOAMI_BOARD(whoami)) {
+	case BCSR_WHOAMI_PB1550_SDR:
+	case BCSR_WHOAMI_PB1550_DDR:
+		bcsr_init(PB1550_BCSR_PHYS_ADDR,
+			  PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+	case BCSR_WHOAMI_DB1550:
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d	"	\
+		"Daughtercard ID %d\n", get_system_type(),
+		(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+	db1550_hw_setup();
+	return 0;
+}
+
+/*****************************************************************************/
+
+static struct mtd_partition db1550_spiflash_parts[] = {
+	{
+		.name	= "spi_flash",
+		.offset = 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct flash_platform_data db1550_spiflash_data = {
+	.name		= "s25fl010",
+	.parts		= db1550_spiflash_parts,
+	.nr_parts	= ARRAY_SIZE(db1550_spiflash_parts),
+	.type		= "m25p10",
+};
+
+static struct spi_board_info db1550_spi_devs[] __initdata = {
+	{
+		/* TI TMP121AIDBVR temp sensor */
+		.modalias	= "tmp121",
+		.max_speed_hz	= 2400000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+	},
+	{
+		/* Spansion S25FL001D0FMA SPI flash */
+		.modalias	= "m25p80",
+		.max_speed_hz	= 2400000,
+		.bus_num	= 0,
+		.chip_select	= 1,
+		.mode		= SPI_MODE_0,
+		.platform_data	= &db1550_spiflash_data,
+	},
+};
+
+static struct i2c_board_info db1550_i2c_devs[] __initdata = {
+	{ I2C_BOARD_INFO("24c04",  0x52),}, /* AT24C04-10 I2C eeprom */
+	{ I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
+	{ I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1550_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+				 unsigned int ctrl)
+{
+	struct nand_chip *this = mtd_to_nand(mtd);
+	unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+	ioaddr &= 0xffffff00;
+
+	if (ctrl & NAND_CLE) {
+		ioaddr += MEM_STNAND_CMD;
+	} else if (ctrl & NAND_ALE) {
+		ioaddr += MEM_STNAND_ADDR;
+	} else {
+		/* assume we want to r/w real data  by default */
+		ioaddr += MEM_STNAND_DATA;
+	}
+	this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+	if (cmd != NAND_CMD_NONE) {
+		__raw_writeb(cmd, this->IO_ADDR_W);
+		wmb();
+	}
+}
+
+static int au1550_nand_device_ready(struct mtd_info *mtd)
+{
+	return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
+}
+
+static struct mtd_partition db1550_nand_parts[] = {
+	{
+		.name	= "NAND FS 0",
+		.offset = 0,
+		.size	= 8 * 1024 * 1024,
+	},
+	{
+		.name	= "NAND FS 1",
+		.offset = MTDPART_OFS_APPEND,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+struct platform_nand_data db1550_nand_platdata = {
+	.chip = {
+		.nr_chips	= 1,
+		.chip_offset	= 0,
+		.nr_partitions	= ARRAY_SIZE(db1550_nand_parts),
+		.partitions	= db1550_nand_parts,
+		.chip_delay	= 20,
+	},
+	.ctrl = {
+		.dev_ready	= au1550_nand_device_ready,
+		.cmd_ctrl	= au1550_nand_cmd_ctrl,
+	},
+};
+
+static struct resource db1550_nand_res[] = {
+	[0] = {
+		.start	= 0x20000000,
+		.end	= 0x200000ff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device db1550_nand_dev = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(db1550_nand_res),
+	.resource	= db1550_nand_res,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &db1550_nand_platdata,
+	}
+};
+
+static struct au1550nd_platdata pb1550_nand_pd = {
+	.parts		= db1550_nand_parts,
+	.num_parts	= ARRAY_SIZE(db1550_nand_parts),
+	.devwidth	= 0,	/* x8 NAND default, needs fixing up */
+};
+
+static struct platform_device pb1550_nand_dev = {
+	.name		= "au1550-nand",
+	.id		= -1,
+	.resource	= db1550_nand_res,
+	.num_resources	= ARRAY_SIZE(db1550_nand_res),
+	.dev		= {
+		.platform_data	= &pb1550_nand_pd,
+	},
+};
+
+static void __init pb1550_nand_setup(void)
+{
+	int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) |
+			    ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
+
+	gpio_direction_input(206);	/* de-assert NAND CS# */
+	switch (boot_swapboot) {
+	case 0: case 2: case 8: case 0xC: case 0xD:
+		/* x16 NAND Flash */
+		pb1550_nand_pd.devwidth = 1;
+		/* fallthrough */
+	case 1: case 3: case 9: case 0xE: case 0xF:
+		/* x8 NAND, already set up */
+		platform_device_register(&pb1550_nand_dev);
+	}
+}
+
+/**********************************************************************/
+
+static struct resource au1550_psc0_res[] = {
+	[0] = {
+		.start	= AU1550_PSC0_PHYS_ADDR,
+		.end	= AU1550_PSC0_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC0_INT,
+		.end	= AU1550_PSC0_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC0_TX,
+		.end	= AU1550_DSCR_CMD0_PSC0_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC0_RX,
+		.end	= AU1550_DSCR_CMD0_PSC0_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+	if (cs)
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
+	else
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1550_spi_platdata = {
+	.mainclk_hz	= 48000000,	/* PSC0 clock: max. 2.4MHz SPI clk */
+	.num_chipselect = 2,
+	.activate_cs	= db1550_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1550_spi_dev = {
+	.dev	= {
+		.dma_mask		= &spi_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1550_spi_platdata,
+	},
+	.name		= "au1550-spi",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1550_psc0_res),
+	.resource	= au1550_psc0_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc1_res[] = {
+	[0] = {
+		.start	= AU1550_PSC1_PHYS_ADDR,
+		.end	= AU1550_PSC1_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC1_INT,
+		.end	= AU1550_PSC1_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC1_TX,
+		.end	= AU1550_DSCR_CMD0_PSC1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC1_RX,
+		.end	= AU1550_DSCR_CMD0_PSC1_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1550_ac97_dev = {
+	.name		= "au1xpsc_ac97",
+	.id		= 1,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1550_psc1_res),
+	.resource	= au1550_psc1_res,
+};
+
+
+static struct resource au1550_psc2_res[] = {
+	[0] = {
+		.start	= AU1550_PSC2_PHYS_ADDR,
+		.end	= AU1550_PSC2_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC2_INT,
+		.end	= AU1550_PSC2_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC2_TX,
+		.end	= AU1550_DSCR_CMD0_PSC2_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC2_RX,
+		.end	= AU1550_DSCR_CMD0_PSC2_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1550_i2c_dev = {
+	.name		= "au1xpsc_smbus",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1550_psc2_res),
+	.resource	= au1550_psc2_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc3_res[] = {
+	[0] = {
+		.start	= AU1550_PSC3_PHYS_ADDR,
+		.end	= AU1550_PSC3_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC3_INT,
+		.end	= AU1550_PSC3_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC3_TX,
+		.end	= AU1550_DSCR_CMD0_PSC3_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC3_RX,
+		.end	= AU1550_DSCR_CMD0_PSC3_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1550_i2s_dev = {
+	.name		= "au1xpsc_i2s",
+	.id		= 3,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1550_psc3_res),
+	.resource	= au1550_psc3_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1550_stac_dev = {
+	.name		= "ac97-codec",
+	.id		= 1,	/* on PSC1 */
+};
+
+static struct platform_device db1550_ac97dma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 1,	/* on PSC3 */
+};
+
+static struct platform_device db1550_i2sdma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 3,	/* on PSC3 */
+};
+
+static struct platform_device db1550_sndac97_dev = {
+	.name		= "db1550-ac97",
+};
+
+static struct platform_device db1550_sndi2s_dev = {
+	.name		= "db1550-i2s",
+};
+
+/**********************************************************************/
+
+static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot < 11) || (slot > 13) || pin == 0)
+		return -1;
+	if (slot == 11)
+		return (pin == 1) ? AU1550_PCI_INTC : 0xff;
+	if (slot == 12) {
+		switch (pin) {
+		case 1: return AU1550_PCI_INTB;
+		case 2: return AU1550_PCI_INTC;
+		case 3: return AU1550_PCI_INTD;
+		case 4: return AU1550_PCI_INTA;
+		}
+	}
+	if (slot == 13) {
+		switch (pin) {
+		case 1: return AU1550_PCI_INTA;
+		case 2: return AU1550_PCI_INTB;
+		case 3: return AU1550_PCI_INTC;
+		case 4: return AU1550_PCI_INTD;
+		}
+	}
+	return -1;
+}
+
+static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot < 12) || (slot > 13) || pin == 0)
+		return -1;
+	if (slot == 12) {
+		switch (pin) {
+		case 1: return AU1500_PCI_INTB;
+		case 2: return AU1500_PCI_INTC;
+		case 3: return AU1500_PCI_INTD;
+		case 4: return AU1500_PCI_INTA;
+		}
+	}
+	if (slot == 13) {
+		switch (pin) {
+		case 1: return AU1500_PCI_INTA;
+		case 2: return AU1500_PCI_INTB;
+		case 3: return AU1500_PCI_INTC;
+		case 4: return AU1500_PCI_INTD;
+		}
+	}
+	return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+	[0] = {
+		.start	= AU1500_PCI_PHYS_ADDR,
+		.end	= AU1500_PCI_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct alchemy_pci_platdata db1550_pci_pd = {
+	.board_map_irq	= db1550_map_pci_irq,
+};
+
+static struct platform_device db1550_pci_host_dev = {
+	.dev.platform_data = &db1550_pci_pd,
+	.name		= "alchemy-pci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(alchemy_pci_host_res),
+	.resource	= alchemy_pci_host_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device *db1550_devs[] __initdata = {
+	&db1550_i2c_dev,
+	&db1550_ac97_dev,
+	&db1550_spi_dev,
+	&db1550_i2s_dev,
+	&db1550_stac_dev,
+	&db1550_ac97dma_dev,
+	&db1550_i2sdma_dev,
+	&db1550_sndac97_dev,
+	&db1550_sndi2s_dev,
+};
+
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+int __init db1550_pci_setup(int id)
+{
+	if (id)
+		db1550_pci_pd.board_map_irq = pb1550_map_pci_irq;
+	return platform_device_register(&db1550_pci_host_dev);
+}
+
+static void __init db1550_devices(void)
+{
+	alchemy_gpio_direction_output(203, 0);	/* red led on */
+
+	irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH);	 /* CD0# */
+	irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH);	 /* CD1# */
+	irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);	 /* CARD0# */
+	irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);	 /* CARD1# */
+	irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
+	irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1550_GPIO3_INT, 0,
+		/*AU1550_GPIO21_INT*/0, 0, 0);
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004000000,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
+		AU1550_GPIO5_INT, 1,
+		/*AU1550_GPIO22_INT*/0, 0, 1);
+
+	platform_device_register(&db1550_nand_dev);
+
+	alchemy_gpio_direction_output(202, 0);	/* green led on */
+}
+
+static void __init pb1550_devices(void)
+{
+	irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH);
+
+	/* enable both PCMCIA card irqs in the shared line */
+	alchemy_gpio2_enable_int(201);	/* socket 0 card irq */
+	alchemy_gpio2_enable_int(202);	/* socket 1 card irq */
+
+	/* Pb1550, like all others, also has statuschange irqs; however they're
+	* wired up on one of the Au1550's shared GPIO201_205 line, which also
+	* services the PCMCIA card interrupts.	So we ignore statuschange and
+	* use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+	* drivers are used to shared irqs and b) statuschange isn't really use-
+	* ful anyway.
+	*/
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008000000,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008000000,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008010000 - 1,
+		AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
+
+	pb1550_nand_setup();
+}
+
+int __init db1550_dev_setup(void)
+{
+	int swapped, id;
+	struct clk *c;
+
+	id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
+
+	i2c_register_board_info(0, db1550_i2c_devs,
+				ARRAY_SIZE(db1550_i2c_devs));
+	spi_register_board_info(db1550_spi_devs,
+				ARRAY_SIZE(db1550_i2c_devs));
+
+	c = clk_get(NULL, "psc0_intclk");
+	if (!IS_ERR(c)) {
+		clk_set_rate(c, 50000000);
+		clk_prepare_enable(c);
+		clk_put(c);
+	}
+	c = clk_get(NULL, "psc2_intclk");
+	if (!IS_ERR(c)) {
+		clk_set_rate(c, db1550_spi_platdata.mainclk_hz);
+		clk_prepare_enable(c);
+		clk_put(c);
+	}
+
+	/* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	/* SPI/I2C use internally supplied 50MHz source */
+	__raw_writel(PSC_SEL_CLK_INTCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	__raw_writel(PSC_SEL_CLK_INTCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+
+	id ? pb1550_devices() : db1550_devices();
+
+	swapped = bcsr_read(BCSR_STATUS) &
+	       (id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT);
+	db1x_register_norflash(128 << 20, 4, swapped);
+
+	return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));
+}