Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

9 files changed, 3283 insertions, 0 deletions

diff --git a/drivers/phy/ti/Kconfig b/drivers/phy/ti/Kconfig
new file mode 100644
index 000000000..205035626
--- /dev/null
+++ b/drivers/phy/ti/Kconfig
@@ -0,0 +1,78 @@
+#
+# Phy drivers for TI platforms
+#
+config PHY_DA8XX_USB
+	tristate "TI DA8xx USB PHY Driver"
+	depends on ARCH_DAVINCI_DA8XX
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the USB PHY on DA8xx SoCs.
+
+	  This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
+
+config PHY_DM816X_USB
+	tristate "TI dm816x USB PHY driver"
+	depends on ARCH_OMAP2PLUS
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this for dm816x USB to work.
+
+config OMAP_CONTROL_PHY
+	tristate "OMAP CONTROL PHY Driver"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	help
+	  Enable this to add support for the PHY part present in the control
+	  module. This driver has API to power on the USB2 PHY and to write to
+	  the mailbox. The mailbox is present only in omap4 and the register to
+	  power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
+	  additional register to power on USB3 PHY/SATA PHY/PCIE PHY
+	  (PIPE3 PHY).
+
+config OMAP_USB2
+	tristate "OMAP USB2 PHY Driver"
+	depends on ARCH_OMAP2PLUS
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	select OMAP_CONTROL_PHY
+	depends on OMAP_OCP2SCP
+	help
+	  Enable this to support the transceiver that is part of SOC. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  The USB OTG controller communicates with the comparator using this
+	  driver.
+
+config TI_PIPE3
+	tristate "TI PIPE3 PHY Driver"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	select GENERIC_PHY
+	select OMAP_CONTROL_PHY
+	depends on OMAP_OCP2SCP
+	help
+	  Enable this to support the PIPE3 PHY that is part of TI SOCs. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  This driver interacts with the "OMAP Control PHY Driver" to power
+	  on/off the PHY.
+
+config PHY_TUSB1210
+	tristate "TI TUSB1210 ULPI PHY module"
+	depends on USB_ULPI_BUS
+	select GENERIC_PHY
+	help
+	  Support for TI TUSB1210 USB ULPI PHY.
+
+config TWL4030_USB
+	tristate "TWL4030 USB Transceiver Driver"
+	depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
+	depends on USB_SUPPORT
+	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this to support the USB OTG transceiver on TWL4030
+	  family chips (including the TWL5030 and TPS659x0 devices).
+	  This transceiver supports high and full speed devices plus,
+	  in host mode, low speed.
diff --git a/drivers/phy/ti/Makefile b/drivers/phy/ti/Makefile
new file mode 100644
index 000000000..9f361756e
--- /dev/null
+++ b/drivers/phy/ti/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_DA8XX_USB)		+= phy-da8xx-usb.o
+obj-$(CONFIG_PHY_DM816X_USB)		+= phy-dm816x-usb.o
+obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
+obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
+obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
+obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
+obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
diff --git a/drivers/phy/ti/phy-da8xx-usb.c b/drivers/phy/ti/phy-da8xx-usb.c
new file mode 100644
index 000000000..befb886ff
--- /dev/null
+++ b/drivers/phy/ti/phy-da8xx-usb.c
@@ -0,0 +1,253 @@
+/*
+ * phy-da8xx-usb - TI DaVinci DA8xx USB PHY driver
+ *
+ * Copyright (C) 2016 David Lechner <david@lechnology.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/mfd/da8xx-cfgchip.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_data/phy-da8xx-usb.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define PHY_INIT_BITS	(CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN)
+
+struct da8xx_usb_phy {
+	struct phy_provider	*phy_provider;
+	struct phy		*usb11_phy;
+	struct phy		*usb20_phy;
+	struct clk		*usb11_clk;
+	struct clk		*usb20_clk;
+	struct regmap		*regmap;
+};
+
+static int da8xx_usb11_phy_power_on(struct phy *phy)
+{
+	struct da8xx_usb_phy *d_phy = phy_get_drvdata(phy);
+	int ret;
+
+	ret = clk_prepare_enable(d_phy->usb11_clk);
+	if (ret)
+		return ret;
+
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2), CFGCHIP2_USB1SUSPENDM,
+			  CFGCHIP2_USB1SUSPENDM);
+
+	return 0;
+}
+
+static int da8xx_usb11_phy_power_off(struct phy *phy)
+{
+	struct da8xx_usb_phy *d_phy = phy_get_drvdata(phy);
+
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2), CFGCHIP2_USB1SUSPENDM, 0);
+
+	clk_disable_unprepare(d_phy->usb11_clk);
+
+	return 0;
+}
+
+static const struct phy_ops da8xx_usb11_phy_ops = {
+	.power_on	= da8xx_usb11_phy_power_on,
+	.power_off	= da8xx_usb11_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int da8xx_usb20_phy_power_on(struct phy *phy)
+{
+	struct da8xx_usb_phy *d_phy = phy_get_drvdata(phy);
+	int ret;
+
+	ret = clk_prepare_enable(d_phy->usb20_clk);
+	if (ret)
+		return ret;
+
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2), CFGCHIP2_OTGPWRDN, 0);
+
+	return 0;
+}
+
+static int da8xx_usb20_phy_power_off(struct phy *phy)
+{
+	struct da8xx_usb_phy *d_phy = phy_get_drvdata(phy);
+
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2), CFGCHIP2_OTGPWRDN,
+			  CFGCHIP2_OTGPWRDN);
+
+	clk_disable_unprepare(d_phy->usb20_clk);
+
+	return 0;
+}
+
+static int da8xx_usb20_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+	struct da8xx_usb_phy *d_phy = phy_get_drvdata(phy);
+	u32 val;
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:		/* Force VBUS valid, ID = 0 */
+		val = CFGCHIP2_OTGMODE_FORCE_HOST;
+		break;
+	case PHY_MODE_USB_DEVICE:	/* Force VBUS valid, ID = 1 */
+		val = CFGCHIP2_OTGMODE_FORCE_DEVICE;
+		break;
+	case PHY_MODE_USB_OTG:	/* Don't override the VBUS/ID comparators */
+		val = CFGCHIP2_OTGMODE_NO_OVERRIDE;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2), CFGCHIP2_OTGMODE_MASK,
+			  val);
+
+	return 0;
+}
+
+static const struct phy_ops da8xx_usb20_phy_ops = {
+	.power_on	= da8xx_usb20_phy_power_on,
+	.power_off	= da8xx_usb20_phy_power_off,
+	.set_mode	= da8xx_usb20_phy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static struct phy *da8xx_usb_phy_of_xlate(struct device *dev,
+					 struct of_phandle_args *args)
+{
+	struct da8xx_usb_phy *d_phy = dev_get_drvdata(dev);
+
+	if (!d_phy)
+		return ERR_PTR(-ENODEV);
+
+	switch (args->args[0]) {
+	case 0:
+		return d_phy->usb20_phy;
+	case 1:
+		return d_phy->usb11_phy;
+	default:
+		return ERR_PTR(-EINVAL);
+	}
+}
+
+static int da8xx_usb_phy_probe(struct platform_device *pdev)
+{
+	struct device		*dev = &pdev->dev;
+	struct da8xx_usb_phy_platform_data *pdata = dev->platform_data;
+	struct device_node	*node = dev->of_node;
+	struct da8xx_usb_phy	*d_phy;
+
+	d_phy = devm_kzalloc(dev, sizeof(*d_phy), GFP_KERNEL);
+	if (!d_phy)
+		return -ENOMEM;
+
+	if (pdata)
+		d_phy->regmap = pdata->cfgchip;
+	else
+		d_phy->regmap = syscon_regmap_lookup_by_compatible(
+							"ti,da830-cfgchip");
+	if (IS_ERR(d_phy->regmap)) {
+		dev_err(dev, "Failed to get syscon\n");
+		return PTR_ERR(d_phy->regmap);
+	}
+
+	d_phy->usb11_clk = devm_clk_get(dev, "usb1_clk48");
+	if (IS_ERR(d_phy->usb11_clk)) {
+		dev_err(dev, "Failed to get usb1_clk48\n");
+		return PTR_ERR(d_phy->usb11_clk);
+	}
+
+	d_phy->usb20_clk = devm_clk_get(dev, "usb0_clk48");
+	if (IS_ERR(d_phy->usb20_clk)) {
+		dev_err(dev, "Failed to get usb0_clk48\n");
+		return PTR_ERR(d_phy->usb20_clk);
+	}
+
+	d_phy->usb11_phy = devm_phy_create(dev, node, &da8xx_usb11_phy_ops);
+	if (IS_ERR(d_phy->usb11_phy)) {
+		dev_err(dev, "Failed to create usb11 phy\n");
+		return PTR_ERR(d_phy->usb11_phy);
+	}
+
+	d_phy->usb20_phy = devm_phy_create(dev, node, &da8xx_usb20_phy_ops);
+	if (IS_ERR(d_phy->usb20_phy)) {
+		dev_err(dev, "Failed to create usb20 phy\n");
+		return PTR_ERR(d_phy->usb20_phy);
+	}
+
+	platform_set_drvdata(pdev, d_phy);
+	phy_set_drvdata(d_phy->usb11_phy, d_phy);
+	phy_set_drvdata(d_phy->usb20_phy, d_phy);
+
+	if (node) {
+		d_phy->phy_provider = devm_of_phy_provider_register(dev,
+							da8xx_usb_phy_of_xlate);
+		if (IS_ERR(d_phy->phy_provider)) {
+			dev_err(dev, "Failed to create phy provider\n");
+			return PTR_ERR(d_phy->phy_provider);
+		}
+	} else {
+		int ret;
+
+		ret = phy_create_lookup(d_phy->usb11_phy, "usb-phy",
+					"ohci-da8xx");
+		if (ret)
+			dev_warn(dev, "Failed to create usb11 phy lookup\n");
+		ret = phy_create_lookup(d_phy->usb20_phy, "usb-phy",
+					"musb-da8xx");
+		if (ret)
+			dev_warn(dev, "Failed to create usb20 phy lookup\n");
+	}
+
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2),
+			  PHY_INIT_BITS, PHY_INIT_BITS);
+
+	return 0;
+}
+
+static int da8xx_usb_phy_remove(struct platform_device *pdev)
+{
+	struct da8xx_usb_phy *d_phy = platform_get_drvdata(pdev);
+
+	if (!pdev->dev.of_node) {
+		phy_remove_lookup(d_phy->usb20_phy, "usb-phy", "musb-da8xx");
+		phy_remove_lookup(d_phy->usb11_phy, "usb-phy", "ohci-da8xx");
+	}
+
+	return 0;
+}
+
+static const struct of_device_id da8xx_usb_phy_ids[] = {
+	{ .compatible = "ti,da830-usb-phy" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, da8xx_usb_phy_ids);
+
+static struct platform_driver da8xx_usb_phy_driver = {
+	.probe	= da8xx_usb_phy_probe,
+	.remove	= da8xx_usb_phy_remove,
+	.driver	= {
+		.name	= "da8xx-usb-phy",
+		.of_match_table = da8xx_usb_phy_ids,
+	},
+};
+
+module_platform_driver(da8xx_usb_phy_driver);
+
+MODULE_ALIAS("platform:da8xx-usb-phy");
+MODULE_AUTHOR("David Lechner <david@lechnology.com>");
+MODULE_DESCRIPTION("TI DA8xx USB PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/ti/phy-dm816x-usb.c b/drivers/phy/ti/phy-dm816x-usb.c
new file mode 100644
index 000000000..2ed5fe20d
--- /dev/null
+++ b/drivers/phy/ti/phy-dm816x-usb.c
@@ -0,0 +1,299 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/usb/phy_companion.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/delay.h>
+#include <linux/phy/phy.h>
+#include <linux/of_platform.h>
+
+#include <linux/mfd/syscon.h>
+
+/*
+ * TRM has two sets of USB_CTRL registers.. The correct register bits
+ * are in TRM section 24.9.8.2 USB_CTRL Register. The TRM documents the
+ * phy as being SR70LX Synopsys USB 2.0 OTG nanoPHY. It also seems at
+ * least dm816x rev c ignores writes to USB_CTRL register, but the TI
+ * kernel is writing to those so it's possible that later revisions
+ * have worknig USB_CTRL register.
+ *
+ * Also note that At least USB_CTRL register seems to be dm816x specific
+ * according to the TRM. It's possible that USBPHY_CTRL is more generic,
+ * but that would have to be checked against the SR70LX documentation
+ * which does not seem to be publicly available.
+ *
+ * Finally, the phy on dm814x and am335x is different from dm816x.
+ */
+#define DM816X_USB_CTRL_PHYCLKSRC	BIT(8)	/* 1 = PLL ref clock */
+#define DM816X_USB_CTRL_PHYSLEEP1	BIT(1)	/* Enable the first phy */
+#define DM816X_USB_CTRL_PHYSLEEP0	BIT(0)	/* Enable the second phy */
+
+#define DM816X_USBPHY_CTRL_TXRISETUNE	1
+#define DM816X_USBPHY_CTRL_TXVREFTUNE	0xc
+#define DM816X_USBPHY_CTRL_TXPREEMTUNE	0x2
+
+struct dm816x_usb_phy {
+	struct regmap *syscon;
+	struct device *dev;
+	unsigned int instance;
+	struct clk *refclk;
+	struct usb_phy phy;
+	unsigned int usb_ctrl;		/* Shared between phy0 and phy1 */
+	unsigned int usbphy_ctrl;
+};
+
+static int dm816x_usb_phy_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	otg->host = host;
+	if (!host)
+		otg->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int dm816x_usb_phy_set_peripheral(struct usb_otg *otg,
+					 struct usb_gadget *gadget)
+{
+	otg->gadget = gadget;
+	if (!gadget)
+		otg->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int dm816x_usb_phy_init(struct phy *x)
+{
+	struct dm816x_usb_phy *phy = phy_get_drvdata(x);
+	unsigned int val;
+	int error;
+
+	if (clk_get_rate(phy->refclk) != 24000000)
+		dev_warn(phy->dev, "nonstandard phy refclk\n");
+
+	/* Set PLL ref clock and put phys to sleep */
+	error = regmap_update_bits(phy->syscon, phy->usb_ctrl,
+				   DM816X_USB_CTRL_PHYCLKSRC |
+				   DM816X_USB_CTRL_PHYSLEEP1 |
+				   DM816X_USB_CTRL_PHYSLEEP0,
+				   0);
+	regmap_read(phy->syscon, phy->usb_ctrl, &val);
+	if ((val & 3) != 0)
+		dev_info(phy->dev,
+			 "Working dm816x USB_CTRL! (0x%08x)\n",
+			 val);
+
+	/*
+	 * TI kernel sets these values for "symmetrical eye diagram and
+	 * better signal quality" so let's assume somebody checked the
+	 * values with a scope and set them here too.
+	 */
+	regmap_read(phy->syscon, phy->usbphy_ctrl, &val);
+	val |= DM816X_USBPHY_CTRL_TXRISETUNE |
+		DM816X_USBPHY_CTRL_TXVREFTUNE |
+		DM816X_USBPHY_CTRL_TXPREEMTUNE;
+	regmap_write(phy->syscon, phy->usbphy_ctrl, val);
+
+	return 0;
+}
+
+static const struct phy_ops ops = {
+	.init		= dm816x_usb_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int __maybe_unused dm816x_usb_phy_runtime_suspend(struct device *dev)
+{
+	struct dm816x_usb_phy *phy = dev_get_drvdata(dev);
+	unsigned int mask, val;
+	int error = 0;
+
+	mask = BIT(phy->instance);
+	val = ~BIT(phy->instance);
+	error = regmap_update_bits(phy->syscon, phy->usb_ctrl,
+				   mask, val);
+	if (error)
+		dev_err(phy->dev, "phy%i failed to power off\n",
+			phy->instance);
+	clk_disable(phy->refclk);
+
+	return 0;
+}
+
+static int __maybe_unused dm816x_usb_phy_runtime_resume(struct device *dev)
+{
+	struct dm816x_usb_phy *phy = dev_get_drvdata(dev);
+	unsigned int mask, val;
+	int error;
+
+	error = clk_enable(phy->refclk);
+	if (error)
+		return error;
+
+	/*
+	 * Note that at least dm816x rev c does not seem to do
+	 * anything with the USB_CTRL register. But let's follow
+	 * what the TI tree is doing in case later revisions use
+	 * USB_CTRL.
+	 */
+	mask = BIT(phy->instance);
+	val = BIT(phy->instance);
+	error = regmap_update_bits(phy->syscon, phy->usb_ctrl,
+				   mask, val);
+	if (error) {
+		dev_err(phy->dev, "phy%i failed to power on\n",
+			phy->instance);
+		clk_disable(phy->refclk);
+		return error;
+	}
+
+	return 0;
+}
+
+static UNIVERSAL_DEV_PM_OPS(dm816x_usb_phy_pm_ops,
+			    dm816x_usb_phy_runtime_suspend,
+			    dm816x_usb_phy_runtime_resume,
+			    NULL);
+
+#ifdef CONFIG_OF
+static const struct of_device_id dm816x_usb_phy_id_table[] = {
+	{
+		.compatible = "ti,dm8168-usb-phy",
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, dm816x_usb_phy_id_table);
+#endif
+
+static int dm816x_usb_phy_probe(struct platform_device *pdev)
+{
+	struct dm816x_usb_phy *phy;
+	struct resource *res;
+	struct phy *generic_phy;
+	struct phy_provider *phy_provider;
+	struct usb_otg *otg;
+	const struct of_device_id *of_id;
+	const struct usb_phy_data *phy_data;
+	int error;
+
+	of_id = of_match_device(of_match_ptr(dm816x_usb_phy_id_table),
+				&pdev->dev);
+	if (!of_id)
+		return -EINVAL;
+
+	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENOENT;
+
+	phy->syscon = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+						      "syscon");
+	if (IS_ERR(phy->syscon))
+		return PTR_ERR(phy->syscon);
+
+	/*
+	 * According to sprs614e.pdf, the first usb_ctrl is shared and
+	 * the second instance for usb_ctrl is reserved.. Also the
+	 * register bits are different from earlier TRMs.
+	 */
+	phy->usb_ctrl = 0x20;
+	phy->usbphy_ctrl = (res->start & 0xff) + 4;
+	if (phy->usbphy_ctrl == 0x2c)
+		phy->instance = 1;
+
+	phy_data = of_id->data;
+
+	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
+	if (!otg)
+		return -ENOMEM;
+
+	phy->dev = &pdev->dev;
+	phy->phy.dev = phy->dev;
+	phy->phy.label = "dm8168_usb_phy";
+	phy->phy.otg = otg;
+	phy->phy.type = USB_PHY_TYPE_USB2;
+	otg->set_host = dm816x_usb_phy_set_host;
+	otg->set_peripheral = dm816x_usb_phy_set_peripheral;
+	otg->usb_phy = &phy->phy;
+
+	platform_set_drvdata(pdev, phy);
+
+	phy->refclk = devm_clk_get(phy->dev, "refclk");
+	if (IS_ERR(phy->refclk))
+		return PTR_ERR(phy->refclk);
+	error = clk_prepare(phy->refclk);
+	if (error)
+		return error;
+
+	pm_runtime_enable(phy->dev);
+	generic_phy = devm_phy_create(phy->dev, NULL, &ops);
+	if (IS_ERR(generic_phy)) {
+		error = PTR_ERR(generic_phy);
+		goto clk_unprepare;
+	}
+
+	phy_set_drvdata(generic_phy, phy);
+
+	phy_provider = devm_of_phy_provider_register(phy->dev,
+						     of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		error = PTR_ERR(phy_provider);
+		goto clk_unprepare;
+	}
+
+	usb_add_phy_dev(&phy->phy);
+
+	return 0;
+
+clk_unprepare:
+	pm_runtime_disable(phy->dev);
+	clk_unprepare(phy->refclk);
+	return error;
+}
+
+static int dm816x_usb_phy_remove(struct platform_device *pdev)
+{
+	struct dm816x_usb_phy *phy = platform_get_drvdata(pdev);
+
+	usb_remove_phy(&phy->phy);
+	pm_runtime_disable(phy->dev);
+	clk_unprepare(phy->refclk);
+
+	return 0;
+}
+
+static struct platform_driver dm816x_usb_phy_driver = {
+	.probe		= dm816x_usb_phy_probe,
+	.remove		= dm816x_usb_phy_remove,
+	.driver		= {
+		.name	= "dm816x-usb-phy",
+		.pm	= &dm816x_usb_phy_pm_ops,
+		.of_match_table = of_match_ptr(dm816x_usb_phy_id_table),
+	},
+};
+
+module_platform_driver(dm816x_usb_phy_driver);
+
+MODULE_ALIAS("platform:dm816x_usb");
+MODULE_AUTHOR("Tony Lindgren <tony@atomide.com>");
+MODULE_DESCRIPTION("dm816x usb phy driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/ti/phy-omap-control.c b/drivers/phy/ti/phy-omap-control.c
new file mode 100644
index 000000000..e9c41b3fa
--- /dev/null
+++ b/drivers/phy/ti/phy-omap-control.c
@@ -0,0 +1,360 @@
+/*
+ * omap-control-phy.c - The PHY part of control module.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/phy/omap_control_phy.h>
+
+/**
+ * omap_control_pcie_pcs - set the PCS delay count
+ * @dev: the control module device
+ * @delay: 8 bit delay value
+ */
+void omap_control_pcie_pcs(struct device *dev, u8 delay)
+{
+	u32 val;
+	struct omap_control_phy	*control_phy;
+
+	if (IS_ERR(dev) || !dev) {
+		pr_err("%s: invalid device\n", __func__);
+		return;
+	}
+
+	control_phy = dev_get_drvdata(dev);
+	if (!control_phy) {
+		dev_err(dev, "%s: invalid control phy device\n", __func__);
+		return;
+	}
+
+	if (control_phy->type != OMAP_CTRL_TYPE_PCIE) {
+		dev_err(dev, "%s: unsupported operation\n", __func__);
+		return;
+	}
+
+	val = readl(control_phy->pcie_pcs);
+	val &= ~(OMAP_CTRL_PCIE_PCS_MASK <<
+		OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT);
+	val |= (delay << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT);
+	writel(val, control_phy->pcie_pcs);
+}
+EXPORT_SYMBOL_GPL(omap_control_pcie_pcs);
+
+/**
+ * omap_control_phy_power - power on/off the phy using control module reg
+ * @dev: the control module device
+ * @on: 0 or 1, based on powering on or off the PHY
+ */
+void omap_control_phy_power(struct device *dev, int on)
+{
+	u32 val;
+	unsigned long rate;
+	struct omap_control_phy	*control_phy;
+
+	if (IS_ERR(dev) || !dev) {
+		pr_err("%s: invalid device\n", __func__);
+		return;
+	}
+
+	control_phy = dev_get_drvdata(dev);
+	if (!control_phy) {
+		dev_err(dev, "%s: invalid control phy device\n", __func__);
+		return;
+	}
+
+	if (control_phy->type == OMAP_CTRL_TYPE_OTGHS)
+		return;
+
+	val = readl(control_phy->power);
+
+	switch (control_phy->type) {
+	case OMAP_CTRL_TYPE_USB2:
+		if (on)
+			val &= ~OMAP_CTRL_DEV_PHY_PD;
+		else
+			val |= OMAP_CTRL_DEV_PHY_PD;
+		break;
+
+	case OMAP_CTRL_TYPE_PCIE:
+	case OMAP_CTRL_TYPE_PIPE3:
+		rate = clk_get_rate(control_phy->sys_clk);
+		rate = rate/1000000;
+
+		if (on) {
+			val &= ~(OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
+				OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK);
+			val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON <<
+				OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+			val |= rate <<
+				OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
+		} else {
+			val &= ~OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK;
+			val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF <<
+				OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+		}
+		break;
+
+	case OMAP_CTRL_TYPE_DRA7USB2:
+		if (on)
+			val &= ~OMAP_CTRL_USB2_PHY_PD;
+		else
+			val |= OMAP_CTRL_USB2_PHY_PD;
+		break;
+
+	case OMAP_CTRL_TYPE_AM437USB2:
+		if (on) {
+			val &= ~(AM437X_CTRL_USB2_PHY_PD |
+					AM437X_CTRL_USB2_OTG_PD);
+			val |= (AM437X_CTRL_USB2_OTGVDET_EN |
+					AM437X_CTRL_USB2_OTGSESSEND_EN);
+		} else {
+			val &= ~(AM437X_CTRL_USB2_OTGVDET_EN |
+					AM437X_CTRL_USB2_OTGSESSEND_EN);
+			val |= (AM437X_CTRL_USB2_PHY_PD |
+					 AM437X_CTRL_USB2_OTG_PD);
+		}
+		break;
+	default:
+		dev_err(dev, "%s: type %d not recognized\n",
+			__func__, control_phy->type);
+		break;
+	}
+
+	writel(val, control_phy->power);
+}
+EXPORT_SYMBOL_GPL(omap_control_phy_power);
+
+/**
+ * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded
+ * @ctrl_phy: struct omap_control_phy *
+ *
+ * Writes to the mailbox register to notify the usb core that a usb
+ * device has been connected.
+ */
+static void omap_control_usb_host_mode(struct omap_control_phy *ctrl_phy)
+{
+	u32 val;
+
+	val = readl(ctrl_phy->otghs_control);
+	val &= ~(OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND);
+	val |= OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID;
+	writel(val, ctrl_phy->otghs_control);
+}
+
+/**
+ * omap_control_usb_device_mode - set AVALID, VBUSVALID and ID pin in high
+ * impedance
+ * @ctrl_phy: struct omap_control_phy *
+ *
+ * Writes to the mailbox register to notify the usb core that it has been
+ * connected to a usb host.
+ */
+static void omap_control_usb_device_mode(struct omap_control_phy *ctrl_phy)
+{
+	u32 val;
+
+	val = readl(ctrl_phy->otghs_control);
+	val &= ~OMAP_CTRL_DEV_SESSEND;
+	val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_AVALID |
+		OMAP_CTRL_DEV_VBUSVALID;
+	writel(val, ctrl_phy->otghs_control);
+}
+
+/**
+ * omap_control_usb_set_sessionend - Enable SESSIONEND and IDIG to high
+ * impedance
+ * @ctrl_phy: struct omap_control_phy *
+ *
+ * Writes to the mailbox register to notify the usb core it's now in
+ * disconnected state.
+ */
+static void omap_control_usb_set_sessionend(struct omap_control_phy *ctrl_phy)
+{
+	u32 val;
+
+	val = readl(ctrl_phy->otghs_control);
+	val &= ~(OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID);
+	val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND;
+	writel(val, ctrl_phy->otghs_control);
+}
+
+/**
+ * omap_control_usb_set_mode - Calls to functions to set USB in one of host mode
+ * or device mode or to denote disconnected state
+ * @dev: the control module device
+ * @mode: The mode to which usb should be configured
+ *
+ * This is an API to write to the mailbox register to notify the usb core that
+ * a usb device has been connected.
+ */
+void omap_control_usb_set_mode(struct device *dev,
+	enum omap_control_usb_mode mode)
+{
+	struct omap_control_phy	*ctrl_phy;
+
+	if (IS_ERR(dev) || !dev)
+		return;
+
+	ctrl_phy = dev_get_drvdata(dev);
+	if (!ctrl_phy) {
+		dev_err(dev, "Invalid control phy device\n");
+		return;
+	}
+
+	if (ctrl_phy->type != OMAP_CTRL_TYPE_OTGHS)
+		return;
+
+	switch (mode) {
+	case USB_MODE_HOST:
+		omap_control_usb_host_mode(ctrl_phy);
+		break;
+	case USB_MODE_DEVICE:
+		omap_control_usb_device_mode(ctrl_phy);
+		break;
+	case USB_MODE_DISCONNECT:
+		omap_control_usb_set_sessionend(ctrl_phy);
+		break;
+	default:
+		dev_vdbg(dev, "invalid omap control usb mode\n");
+	}
+}
+EXPORT_SYMBOL_GPL(omap_control_usb_set_mode);
+
+static const enum omap_control_phy_type otghs_data = OMAP_CTRL_TYPE_OTGHS;
+static const enum omap_control_phy_type usb2_data = OMAP_CTRL_TYPE_USB2;
+static const enum omap_control_phy_type pipe3_data = OMAP_CTRL_TYPE_PIPE3;
+static const enum omap_control_phy_type pcie_data = OMAP_CTRL_TYPE_PCIE;
+static const enum omap_control_phy_type dra7usb2_data = OMAP_CTRL_TYPE_DRA7USB2;
+static const enum omap_control_phy_type am437usb2_data = OMAP_CTRL_TYPE_AM437USB2;
+
+static const struct of_device_id omap_control_phy_id_table[] = {
+	{
+		.compatible = "ti,control-phy-otghs",
+		.data = &otghs_data,
+	},
+	{
+		.compatible = "ti,control-phy-usb2",
+		.data = &usb2_data,
+	},
+	{
+		.compatible = "ti,control-phy-pipe3",
+		.data = &pipe3_data,
+	},
+	{
+		.compatible = "ti,control-phy-pcie",
+		.data = &pcie_data,
+	},
+	{
+		.compatible = "ti,control-phy-usb2-dra7",
+		.data = &dra7usb2_data,
+	},
+	{
+		.compatible = "ti,control-phy-usb2-am437",
+		.data = &am437usb2_data,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap_control_phy_id_table);
+
+static int omap_control_phy_probe(struct platform_device *pdev)
+{
+	struct resource	*res;
+	const struct of_device_id *of_id;
+	struct omap_control_phy *control_phy;
+
+	of_id = of_match_device(omap_control_phy_id_table, &pdev->dev);
+	if (!of_id)
+		return -EINVAL;
+
+	control_phy = devm_kzalloc(&pdev->dev, sizeof(*control_phy),
+		GFP_KERNEL);
+	if (!control_phy)
+		return -ENOMEM;
+
+	control_phy->dev = &pdev->dev;
+	control_phy->type = *(enum omap_control_phy_type *)of_id->data;
+
+	if (control_phy->type == OMAP_CTRL_TYPE_OTGHS) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+			"otghs_control");
+		control_phy->otghs_control = devm_ioremap_resource(
+			&pdev->dev, res);
+		if (IS_ERR(control_phy->otghs_control))
+			return PTR_ERR(control_phy->otghs_control);
+	} else {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+				"power");
+		control_phy->power = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(control_phy->power)) {
+			dev_err(&pdev->dev, "Couldn't get power register\n");
+			return PTR_ERR(control_phy->power);
+		}
+	}
+
+	if (control_phy->type == OMAP_CTRL_TYPE_PIPE3 ||
+	    control_phy->type == OMAP_CTRL_TYPE_PCIE) {
+		control_phy->sys_clk = devm_clk_get(control_phy->dev,
+			"sys_clkin");
+		if (IS_ERR(control_phy->sys_clk)) {
+			pr_err("%s: unable to get sys_clkin\n", __func__);
+			return -EINVAL;
+		}
+	}
+
+	if (control_phy->type == OMAP_CTRL_TYPE_PCIE) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   "pcie_pcs");
+		control_phy->pcie_pcs = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(control_phy->pcie_pcs))
+			return PTR_ERR(control_phy->pcie_pcs);
+	}
+
+	dev_set_drvdata(control_phy->dev, control_phy);
+
+	return 0;
+}
+
+static struct platform_driver omap_control_phy_driver = {
+	.probe		= omap_control_phy_probe,
+	.driver		= {
+		.name	= "omap-control-phy",
+		.of_match_table = omap_control_phy_id_table,
+	},
+};
+
+static int __init omap_control_phy_init(void)
+{
+	return platform_driver_register(&omap_control_phy_driver);
+}
+subsys_initcall(omap_control_phy_init);
+
+static void __exit omap_control_phy_exit(void)
+{
+	platform_driver_unregister(&omap_control_phy_driver);
+}
+module_exit(omap_control_phy_exit);
+
+MODULE_ALIAS("platform:omap_control_phy");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP Control Module PHY Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/ti/phy-omap-usb2.c b/drivers/phy/ti/phy-omap-usb2.c
new file mode 100644
index 000000000..fe909fd81
--- /dev/null
+++ b/drivers/phy/ti/phy-omap-usb2.c
@@ -0,0 +1,439 @@
+/*
+ * omap-usb2.c - USB PHY, talking to musb controller in OMAP.
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/phy/omap_usb.h>
+#include <linux/usb/phy_companion.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/delay.h>
+#include <linux/phy/omap_control_phy.h>
+#include <linux/phy/phy.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/of_platform.h>
+
+#define USB2PHY_DISCON_BYP_LATCH (1 << 31)
+#define USB2PHY_ANA_CONFIG1 0x4c
+
+/**
+ * omap_usb2_set_comparator - links the comparator present in the sytem with
+ *	this phy
+ * @comparator - the companion phy(comparator) for this phy
+ *
+ * The phy companion driver should call this API passing the phy_companion
+ * filled with set_vbus and start_srp to be used by usb phy.
+ *
+ * For use by phy companion driver
+ */
+int omap_usb2_set_comparator(struct phy_companion *comparator)
+{
+	struct omap_usb	*phy;
+	struct usb_phy	*x = usb_get_phy(USB_PHY_TYPE_USB2);
+
+	if (IS_ERR(x))
+		return -ENODEV;
+
+	phy = phy_to_omapusb(x);
+	phy->comparator = comparator;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(omap_usb2_set_comparator);
+
+static int omap_usb_set_vbus(struct usb_otg *otg, bool enabled)
+{
+	struct omap_usb *phy = phy_to_omapusb(otg->usb_phy);
+
+	if (!phy->comparator)
+		return -ENODEV;
+
+	return phy->comparator->set_vbus(phy->comparator, enabled);
+}
+
+static int omap_usb_start_srp(struct usb_otg *otg)
+{
+	struct omap_usb *phy = phy_to_omapusb(otg->usb_phy);
+
+	if (!phy->comparator)
+		return -ENODEV;
+
+	return phy->comparator->start_srp(phy->comparator);
+}
+
+static int omap_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	otg->host = host;
+	if (!host)
+		otg->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int omap_usb_set_peripheral(struct usb_otg *otg,
+		struct usb_gadget *gadget)
+{
+	otg->gadget = gadget;
+	if (!gadget)
+		otg->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int omap_usb_phy_power(struct omap_usb *phy, int on)
+{
+	u32 val;
+	int ret;
+
+	if (!phy->syscon_phy_power) {
+		omap_control_phy_power(phy->control_dev, on);
+		return 0;
+	}
+
+	if (on)
+		val = phy->power_on;
+	else
+		val = phy->power_off;
+
+	ret = regmap_update_bits(phy->syscon_phy_power, phy->power_reg,
+				 phy->mask, val);
+	return ret;
+}
+
+static int omap_usb_power_off(struct phy *x)
+{
+	struct omap_usb *phy = phy_get_drvdata(x);
+
+	return omap_usb_phy_power(phy, false);
+}
+
+static int omap_usb_power_on(struct phy *x)
+{
+	struct omap_usb *phy = phy_get_drvdata(x);
+
+	return omap_usb_phy_power(phy, true);
+}
+
+static int omap_usb2_disable_clocks(struct omap_usb *phy)
+{
+	clk_disable(phy->wkupclk);
+	if (!IS_ERR(phy->optclk))
+		clk_disable(phy->optclk);
+
+	return 0;
+}
+
+static int omap_usb2_enable_clocks(struct omap_usb *phy)
+{
+	int ret;
+
+	ret = clk_enable(phy->wkupclk);
+	if (ret < 0) {
+		dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
+		goto err0;
+	}
+
+	if (!IS_ERR(phy->optclk)) {
+		ret = clk_enable(phy->optclk);
+		if (ret < 0) {
+			dev_err(phy->dev, "Failed to enable optclk %d\n", ret);
+			goto err1;
+		}
+	}
+
+	return 0;
+
+err1:
+	clk_disable(phy->wkupclk);
+
+err0:
+	return ret;
+}
+
+static int omap_usb_init(struct phy *x)
+{
+	struct omap_usb *phy = phy_get_drvdata(x);
+	u32 val;
+
+	omap_usb2_enable_clocks(phy);
+
+	if (phy->flags & OMAP_USB2_CALIBRATE_FALSE_DISCONNECT) {
+		/*
+		 *
+		 * Reduce the sensitivity of internal PHY by enabling the
+		 * DISCON_BYP_LATCH of the USB2PHY_ANA_CONFIG1 register. This
+		 * resolves issues with certain devices which can otherwise
+		 * be prone to false disconnects.
+		 *
+		 */
+		val = omap_usb_readl(phy->phy_base, USB2PHY_ANA_CONFIG1);
+		val |= USB2PHY_DISCON_BYP_LATCH;
+		omap_usb_writel(phy->phy_base, USB2PHY_ANA_CONFIG1, val);
+	}
+
+	return 0;
+}
+
+static int omap_usb_exit(struct phy *x)
+{
+	struct omap_usb *phy = phy_get_drvdata(x);
+
+	return omap_usb2_disable_clocks(phy);
+}
+
+static const struct phy_ops ops = {
+	.init		= omap_usb_init,
+	.exit		= omap_usb_exit,
+	.power_on	= omap_usb_power_on,
+	.power_off	= omap_usb_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static const struct usb_phy_data omap_usb2_data = {
+	.label = "omap_usb2",
+	.flags = OMAP_USB2_HAS_START_SRP | OMAP_USB2_HAS_SET_VBUS,
+	.mask = OMAP_DEV_PHY_PD,
+	.power_off = OMAP_DEV_PHY_PD,
+};
+
+static const struct usb_phy_data omap5_usb2_data = {
+	.label = "omap5_usb2",
+	.flags = 0,
+	.mask = OMAP_DEV_PHY_PD,
+	.power_off = OMAP_DEV_PHY_PD,
+};
+
+static const struct usb_phy_data dra7x_usb2_data = {
+	.label = "dra7x_usb2",
+	.flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT,
+	.mask = OMAP_DEV_PHY_PD,
+	.power_off = OMAP_DEV_PHY_PD,
+};
+
+static const struct usb_phy_data dra7x_usb2_phy2_data = {
+	.label = "dra7x_usb2_phy2",
+	.flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT,
+	.mask = OMAP_USB2_PHY_PD,
+	.power_off = OMAP_USB2_PHY_PD,
+};
+
+static const struct usb_phy_data am437x_usb2_data = {
+	.label = "am437x_usb2",
+	.flags =  0,
+	.mask = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD |
+		AM437X_USB2_OTGVDET_EN | AM437X_USB2_OTGSESSEND_EN,
+	.power_on = AM437X_USB2_OTGVDET_EN | AM437X_USB2_OTGSESSEND_EN,
+	.power_off = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD,
+};
+
+static const struct of_device_id omap_usb2_id_table[] = {
+	{
+		.compatible = "ti,omap-usb2",
+		.data = &omap_usb2_data,
+	},
+	{
+		.compatible = "ti,omap5-usb2",
+		.data = &omap5_usb2_data,
+	},
+	{
+		.compatible = "ti,dra7x-usb2",
+		.data = &dra7x_usb2_data,
+	},
+	{
+		.compatible = "ti,dra7x-usb2-phy2",
+		.data = &dra7x_usb2_phy2_data,
+	},
+	{
+		.compatible = "ti,am437x-usb2",
+		.data = &am437x_usb2_data,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+
+static int omap_usb2_probe(struct platform_device *pdev)
+{
+	struct omap_usb	*phy;
+	struct phy *generic_phy;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+	struct usb_otg *otg;
+	struct device_node *node = pdev->dev.of_node;
+	struct device_node *control_node;
+	struct platform_device *control_pdev;
+	const struct of_device_id *of_id;
+	struct usb_phy_data *phy_data;
+
+	of_id = of_match_device(omap_usb2_id_table, &pdev->dev);
+
+	if (!of_id)
+		return -EINVAL;
+
+	phy_data = (struct usb_phy_data *)of_id->data;
+
+	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
+	if (!otg)
+		return -ENOMEM;
+
+	phy->dev		= &pdev->dev;
+
+	phy->phy.dev		= phy->dev;
+	phy->phy.label		= phy_data->label;
+	phy->phy.otg		= otg;
+	phy->phy.type		= USB_PHY_TYPE_USB2;
+	phy->mask		= phy_data->mask;
+	phy->power_on		= phy_data->power_on;
+	phy->power_off		= phy_data->power_off;
+
+	if (phy_data->flags & OMAP_USB2_CALIBRATE_FALSE_DISCONNECT) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		phy->phy_base = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(phy->phy_base))
+			return PTR_ERR(phy->phy_base);
+		phy->flags |= OMAP_USB2_CALIBRATE_FALSE_DISCONNECT;
+	}
+
+	phy->syscon_phy_power = syscon_regmap_lookup_by_phandle(node,
+							"syscon-phy-power");
+	if (IS_ERR(phy->syscon_phy_power)) {
+		dev_dbg(&pdev->dev,
+			"can't get syscon-phy-power, using control device\n");
+		phy->syscon_phy_power = NULL;
+
+		control_node = of_parse_phandle(node, "ctrl-module", 0);
+		if (!control_node) {
+			dev_err(&pdev->dev,
+				"Failed to get control device phandle\n");
+			return -EINVAL;
+		}
+
+		control_pdev = of_find_device_by_node(control_node);
+		if (!control_pdev) {
+			dev_err(&pdev->dev, "Failed to get control device\n");
+			return -EINVAL;
+		}
+		phy->control_dev = &control_pdev->dev;
+	} else {
+		if (of_property_read_u32_index(node,
+					       "syscon-phy-power", 1,
+					       &phy->power_reg)) {
+			dev_err(&pdev->dev,
+				"couldn't get power reg. offset\n");
+			return -EINVAL;
+		}
+	}
+
+	otg->set_host		= omap_usb_set_host;
+	otg->set_peripheral	= omap_usb_set_peripheral;
+	if (phy_data->flags & OMAP_USB2_HAS_SET_VBUS)
+		otg->set_vbus		= omap_usb_set_vbus;
+	if (phy_data->flags & OMAP_USB2_HAS_START_SRP)
+		otg->start_srp		= omap_usb_start_srp;
+	otg->usb_phy		= &phy->phy;
+
+	platform_set_drvdata(pdev, phy);
+	pm_runtime_enable(phy->dev);
+
+	generic_phy = devm_phy_create(phy->dev, NULL, &ops);
+	if (IS_ERR(generic_phy)) {
+		pm_runtime_disable(phy->dev);
+		return PTR_ERR(generic_phy);
+	}
+
+	phy_set_drvdata(generic_phy, phy);
+	omap_usb_power_off(generic_phy);
+
+	phy_provider = devm_of_phy_provider_register(phy->dev,
+			of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		pm_runtime_disable(phy->dev);
+		return PTR_ERR(phy_provider);
+	}
+
+	phy->wkupclk = devm_clk_get(phy->dev, "wkupclk");
+	if (IS_ERR(phy->wkupclk)) {
+		dev_warn(&pdev->dev, "unable to get wkupclk, trying old name\n");
+		phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
+		if (IS_ERR(phy->wkupclk)) {
+			dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
+			pm_runtime_disable(phy->dev);
+			return PTR_ERR(phy->wkupclk);
+		} else {
+			dev_warn(&pdev->dev,
+				 "found usb_phy_cm_clk32k, please fix DTS\n");
+		}
+	}
+	clk_prepare(phy->wkupclk);
+
+	phy->optclk = devm_clk_get(phy->dev, "refclk");
+	if (IS_ERR(phy->optclk)) {
+		dev_dbg(&pdev->dev, "unable to get refclk, trying old name\n");
+		phy->optclk = devm_clk_get(phy->dev, "usb_otg_ss_refclk960m");
+		if (IS_ERR(phy->optclk)) {
+			dev_dbg(&pdev->dev,
+				"unable to get usb_otg_ss_refclk960m\n");
+		} else {
+			dev_warn(&pdev->dev,
+				 "found usb_otg_ss_refclk960m, please fix DTS\n");
+		}
+	}
+
+	if (!IS_ERR(phy->optclk))
+		clk_prepare(phy->optclk);
+
+	usb_add_phy_dev(&phy->phy);
+
+	return 0;
+}
+
+static int omap_usb2_remove(struct platform_device *pdev)
+{
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	clk_unprepare(phy->wkupclk);
+	if (!IS_ERR(phy->optclk))
+		clk_unprepare(phy->optclk);
+	usb_remove_phy(&phy->phy);
+	pm_runtime_disable(phy->dev);
+
+	return 0;
+}
+
+static struct platform_driver omap_usb2_driver = {
+	.probe		= omap_usb2_probe,
+	.remove		= omap_usb2_remove,
+	.driver		= {
+		.name	= "omap-usb2",
+		.of_match_table = omap_usb2_id_table,
+	},
+};
+
+module_platform_driver(omap_usb2_driver);
+
+MODULE_ALIAS("platform:omap_usb2");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP USB2 phy driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c
new file mode 100644
index 000000000..693acc167
--- /dev/null
+++ b/drivers/phy/ti/phy-ti-pipe3.c
@@ -0,0 +1,796 @@
+/*
+ * phy-ti-pipe3 - PIPE3 PHY driver.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/phy/phy.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/pm_runtime.h>
+#include <linux/delay.h>
+#include <linux/phy/omap_control_phy.h>
+#include <linux/of_platform.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+#define	PLL_STATUS		0x00000004
+#define	PLL_GO			0x00000008
+#define	PLL_CONFIGURATION1	0x0000000C
+#define	PLL_CONFIGURATION2	0x00000010
+#define	PLL_CONFIGURATION3	0x00000014
+#define	PLL_CONFIGURATION4	0x00000020
+
+#define	PLL_REGM_MASK		0x001FFE00
+#define	PLL_REGM_SHIFT		0x9
+#define	PLL_REGM_F_MASK		0x0003FFFF
+#define	PLL_REGM_F_SHIFT	0x0
+#define	PLL_REGN_MASK		0x000001FE
+#define	PLL_REGN_SHIFT		0x1
+#define	PLL_SELFREQDCO_MASK	0x0000000E
+#define	PLL_SELFREQDCO_SHIFT	0x1
+#define	PLL_SD_MASK		0x0003FC00
+#define	PLL_SD_SHIFT		10
+#define	SET_PLL_GO		0x1
+#define PLL_LDOPWDN		BIT(15)
+#define PLL_TICOPWDN		BIT(16)
+#define	PLL_LOCK		0x2
+#define	PLL_IDLE		0x1
+
+#define SATA_PLL_SOFT_RESET	BIT(18)
+
+#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK	0x003FC000
+#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT	14
+
+#define PIPE3_PHY_PWRCTL_CLK_FREQ_MASK	0xFFC00000
+#define PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT	22
+
+#define PIPE3_PHY_TX_RX_POWERON		0x3
+#define PIPE3_PHY_TX_RX_POWEROFF	0x0
+
+#define PCIE_PCS_MASK			0xFF0000
+#define PCIE_PCS_DELAY_COUNT_SHIFT	0x10
+
+#define PCIEPHYRX_ANA_PROGRAMMABILITY	0x0000000C
+#define INTERFACE_MASK			GENMASK(31, 27)
+#define INTERFACE_SHIFT			27
+#define LOSD_MASK			GENMASK(17, 14)
+#define LOSD_SHIFT			14
+#define MEM_PLLDIV			GENMASK(6, 5)
+
+#define PCIEPHYRX_TRIM			0x0000001C
+#define MEM_DLL_TRIM_SEL		GENMASK(31, 30)
+#define MEM_DLL_TRIM_SHIFT		30
+
+#define PCIEPHYRX_DLL			0x00000024
+#define MEM_DLL_PHINT_RATE		GENMASK(31, 30)
+
+#define PCIEPHYRX_DIGITAL_MODES		0x00000028
+#define MEM_CDR_FASTLOCK		BIT(23)
+#define MEM_CDR_LBW			GENMASK(22, 21)
+#define MEM_CDR_STEPCNT			GENMASK(20, 19)
+#define MEM_CDR_STL_MASK		GENMASK(18, 16)
+#define MEM_CDR_STL_SHIFT		16
+#define MEM_CDR_THR_MASK		GENMASK(15, 13)
+#define MEM_CDR_THR_SHIFT		13
+#define MEM_CDR_THR_MODE		BIT(12)
+#define MEM_CDR_CDR_2NDO_SDM_MODE	BIT(11)
+#define MEM_OVRD_HS_RATE		BIT(26)
+
+#define PCIEPHYRX_EQUALIZER		0x00000038
+#define MEM_EQLEV			GENMASK(31, 16)
+#define MEM_EQFTC			GENMASK(15, 11)
+#define MEM_EQCTL			GENMASK(10, 7)
+#define MEM_EQCTL_SHIFT			7
+#define MEM_OVRD_EQLEV			BIT(2)
+#define MEM_OVRD_EQFTC			BIT(1)
+
+/*
+ * This is an Empirical value that works, need to confirm the actual
+ * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status
+ * to be correctly reflected in the PIPE3PHY_PLL_STATUS register.
+ */
+#define PLL_IDLE_TIME	100	/* in milliseconds */
+#define PLL_LOCK_TIME	100	/* in milliseconds */
+
+struct pipe3_dpll_params {
+	u16	m;
+	u8	n;
+	u8	freq:3;
+	u8	sd;
+	u32	mf;
+};
+
+struct pipe3_dpll_map {
+	unsigned long rate;
+	struct pipe3_dpll_params params;
+};
+
+struct ti_pipe3 {
+	void __iomem		*pll_ctrl_base;
+	void __iomem		*phy_rx;
+	void __iomem		*phy_tx;
+	struct device		*dev;
+	struct device		*control_dev;
+	struct clk		*wkupclk;
+	struct clk		*sys_clk;
+	struct clk		*refclk;
+	struct clk		*div_clk;
+	struct pipe3_dpll_map	*dpll_map;
+	struct regmap		*phy_power_syscon; /* ctrl. reg. acces */
+	struct regmap		*pcs_syscon; /* ctrl. reg. acces */
+	struct regmap		*dpll_reset_syscon; /* ctrl. reg. acces */
+	unsigned int		dpll_reset_reg; /* reg. index within syscon */
+	unsigned int		power_reg; /* power reg. index within syscon */
+	unsigned int		pcie_pcs_reg; /* pcs reg. index in syscon */
+	bool			sata_refclk_enabled;
+};
+
+static struct pipe3_dpll_map dpll_map_usb[] = {
+	{12000000, {1250, 5, 4, 20, 0} },	/* 12 MHz */
+	{16800000, {3125, 20, 4, 20, 0} },	/* 16.8 MHz */
+	{19200000, {1172, 8, 4, 20, 65537} },	/* 19.2 MHz */
+	{20000000, {1000, 7, 4, 10, 0} },	/* 20 MHz */
+	{26000000, {1250, 12, 4, 20, 0} },	/* 26 MHz */
+	{38400000, {3125, 47, 4, 20, 92843} },	/* 38.4 MHz */
+	{ },					/* Terminator */
+};
+
+static struct pipe3_dpll_map dpll_map_sata[] = {
+	{12000000, {625, 4, 4, 6, 0} },	/* 12 MHz */
+	{16800000, {625, 6, 4, 7, 0} },		/* 16.8 MHz */
+	{19200000, {625, 7, 4, 6, 0} },		/* 19.2 MHz */
+	{20000000, {750, 9, 4, 6, 0} },		/* 20 MHz */
+	{26000000, {750, 12, 4, 6, 0} },	/* 26 MHz */
+	{38400000, {625, 15, 4, 6, 0} },	/* 38.4 MHz */
+	{ },					/* Terminator */
+};
+
+static inline u32 ti_pipe3_readl(void __iomem *addr, unsigned offset)
+{
+	return __raw_readl(addr + offset);
+}
+
+static inline void ti_pipe3_writel(void __iomem *addr, unsigned offset,
+	u32 data)
+{
+	__raw_writel(data, addr + offset);
+}
+
+static struct pipe3_dpll_params *ti_pipe3_get_dpll_params(struct ti_pipe3 *phy)
+{
+	unsigned long rate;
+	struct pipe3_dpll_map *dpll_map = phy->dpll_map;
+
+	rate = clk_get_rate(phy->sys_clk);
+
+	for (; dpll_map->rate; dpll_map++) {
+		if (rate == dpll_map->rate)
+			return &dpll_map->params;
+	}
+
+	dev_err(phy->dev, "No DPLL configuration for %lu Hz SYS CLK\n", rate);
+
+	return NULL;
+}
+
+static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy);
+static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy);
+
+static int ti_pipe3_power_off(struct phy *x)
+{
+	u32 val;
+	int ret;
+	struct ti_pipe3 *phy = phy_get_drvdata(x);
+
+	if (!phy->phy_power_syscon) {
+		omap_control_phy_power(phy->control_dev, 0);
+		return 0;
+	}
+
+	val = PIPE3_PHY_TX_RX_POWEROFF << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+
+	ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
+				 PIPE3_PHY_PWRCTL_CLK_CMD_MASK, val);
+	return ret;
+}
+
+static int ti_pipe3_power_on(struct phy *x)
+{
+	u32 val;
+	u32 mask;
+	int ret;
+	unsigned long rate;
+	struct ti_pipe3 *phy = phy_get_drvdata(x);
+
+	if (!phy->phy_power_syscon) {
+		omap_control_phy_power(phy->control_dev, 1);
+		return 0;
+	}
+
+	rate = clk_get_rate(phy->sys_clk);
+	if (!rate) {
+		dev_err(phy->dev, "Invalid clock rate\n");
+		return -EINVAL;
+	}
+	rate = rate / 1000000;
+	mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
+		  OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK;
+	val = PIPE3_PHY_TX_RX_POWERON << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+	val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
+
+	ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
+				 mask, val);
+	return ret;
+}
+
+static int ti_pipe3_dpll_wait_lock(struct ti_pipe3 *phy)
+{
+	u32		val;
+	unsigned long	timeout;
+
+	timeout = jiffies + msecs_to_jiffies(PLL_LOCK_TIME);
+	do {
+		cpu_relax();
+		val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_STATUS);
+		if (val & PLL_LOCK)
+			return 0;
+	} while (!time_after(jiffies, timeout));
+
+	dev_err(phy->dev, "DPLL failed to lock\n");
+	return -EBUSY;
+}
+
+static int ti_pipe3_dpll_program(struct ti_pipe3 *phy)
+{
+	u32			val;
+	struct pipe3_dpll_params *dpll_params;
+
+	dpll_params = ti_pipe3_get_dpll_params(phy);
+	if (!dpll_params)
+		return -EINVAL;
+
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
+	val &= ~PLL_REGN_MASK;
+	val |= dpll_params->n << PLL_REGN_SHIFT;
+	ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
+
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
+	val &= ~PLL_SELFREQDCO_MASK;
+	val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
+	ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
+	val &= ~PLL_REGM_MASK;
+	val |= dpll_params->m << PLL_REGM_SHIFT;
+	ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
+
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
+	val &= ~PLL_REGM_F_MASK;
+	val |= dpll_params->mf << PLL_REGM_F_SHIFT;
+	ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);
+
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
+	val &= ~PLL_SD_MASK;
+	val |= dpll_params->sd << PLL_SD_SHIFT;
+	ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);
+
+	ti_pipe3_writel(phy->pll_ctrl_base, PLL_GO, SET_PLL_GO);
+
+	return ti_pipe3_dpll_wait_lock(phy);
+}
+
+static void ti_pipe3_calibrate(struct ti_pipe3 *phy)
+{
+	u32 val;
+
+	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY);
+	val &= ~(INTERFACE_MASK | LOSD_MASK | MEM_PLLDIV);
+	val |= (0x1 << INTERFACE_SHIFT | 0xA << LOSD_SHIFT);
+	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES);
+	val &= ~(MEM_CDR_STEPCNT | MEM_CDR_STL_MASK | MEM_CDR_THR_MASK |
+		 MEM_CDR_CDR_2NDO_SDM_MODE | MEM_OVRD_HS_RATE);
+	val |= (MEM_CDR_FASTLOCK | MEM_CDR_LBW | 0x3 << MEM_CDR_STL_SHIFT |
+		0x1 << MEM_CDR_THR_SHIFT | MEM_CDR_THR_MODE);
+	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_TRIM);
+	val &= ~MEM_DLL_TRIM_SEL;
+	val |= 0x2 << MEM_DLL_TRIM_SHIFT;
+	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_TRIM, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DLL);
+	val |= MEM_DLL_PHINT_RATE;
+	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DLL, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_EQUALIZER);
+	val &= ~(MEM_EQLEV | MEM_EQCTL | MEM_OVRD_EQLEV | MEM_OVRD_EQFTC);
+	val |= MEM_EQFTC | 0x1 << MEM_EQCTL_SHIFT;
+	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_EQUALIZER, val);
+}
+
+static int ti_pipe3_init(struct phy *x)
+{
+	struct ti_pipe3 *phy = phy_get_drvdata(x);
+	u32 val;
+	int ret = 0;
+
+	ti_pipe3_enable_clocks(phy);
+	/*
+	 * Set pcie_pcs register to 0x96 for proper functioning of phy
+	 * as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
+	 * 18-1804.
+	 */
+	if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
+		if (!phy->pcs_syscon) {
+			omap_control_pcie_pcs(phy->control_dev, 0x96);
+			return 0;
+		}
+
+		val = 0x96 << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT;
+		ret = regmap_update_bits(phy->pcs_syscon, phy->pcie_pcs_reg,
+					 PCIE_PCS_MASK, val);
+		if (ret)
+			return ret;
+
+		ti_pipe3_calibrate(phy);
+
+		return 0;
+	}
+
+	/* Bring it out of IDLE if it is IDLE */
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
+	if (val & PLL_IDLE) {
+		val &= ~PLL_IDLE;
+		ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
+		ret = ti_pipe3_dpll_wait_lock(phy);
+	}
+
+	/* SATA has issues if re-programmed when locked */
+	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_STATUS);
+	if ((val & PLL_LOCK) && of_device_is_compatible(phy->dev->of_node,
+							"ti,phy-pipe3-sata"))
+		return ret;
+
+	/* Program the DPLL */
+	ret = ti_pipe3_dpll_program(phy);
+	if (ret) {
+		ti_pipe3_disable_clocks(phy);
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static int ti_pipe3_exit(struct phy *x)
+{
+	struct ti_pipe3 *phy = phy_get_drvdata(x);
+	u32 val;
+	unsigned long timeout;
+
+	/* If dpll_reset_syscon is not present we wont power down SATA DPLL
+	 * due to Errata i783
+	 */
+	if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-sata") &&
+	    !phy->dpll_reset_syscon)
+		return 0;
+
+	/* PCIe doesn't have internal DPLL */
+	if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
+		/* Put DPLL in IDLE mode */
+		val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
+		val |= PLL_IDLE;
+		ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+		/* wait for LDO and Oscillator to power down */
+		timeout = jiffies + msecs_to_jiffies(PLL_IDLE_TIME);
+		do {
+			cpu_relax();
+			val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_STATUS);
+			if ((val & PLL_TICOPWDN) && (val & PLL_LDOPWDN))
+				break;
+		} while (!time_after(jiffies, timeout));
+
+		if (!(val & PLL_TICOPWDN) || !(val & PLL_LDOPWDN)) {
+			dev_err(phy->dev, "Failed to power down: PLL_STATUS 0x%x\n",
+				val);
+			return -EBUSY;
+		}
+	}
+
+	/* i783: SATA needs control bit toggle after PLL unlock */
+	if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-sata")) {
+		regmap_update_bits(phy->dpll_reset_syscon, phy->dpll_reset_reg,
+				   SATA_PLL_SOFT_RESET, SATA_PLL_SOFT_RESET);
+		regmap_update_bits(phy->dpll_reset_syscon, phy->dpll_reset_reg,
+				   SATA_PLL_SOFT_RESET, 0);
+	}
+
+	ti_pipe3_disable_clocks(phy);
+
+	return 0;
+}
+static const struct phy_ops ops = {
+	.init		= ti_pipe3_init,
+	.exit		= ti_pipe3_exit,
+	.power_on	= ti_pipe3_power_on,
+	.power_off	= ti_pipe3_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id ti_pipe3_id_table[];
+
+static int ti_pipe3_get_clk(struct ti_pipe3 *phy)
+{
+	struct clk *clk;
+	struct device *dev = phy->dev;
+	struct device_node *node = dev->of_node;
+
+	phy->refclk = devm_clk_get(dev, "refclk");
+	if (IS_ERR(phy->refclk)) {
+		dev_err(dev, "unable to get refclk\n");
+		/* older DTBs have missing refclk in SATA PHY
+		 * so don't bail out in case of SATA PHY.
+		 */
+		if (!of_device_is_compatible(node, "ti,phy-pipe3-sata"))
+			return PTR_ERR(phy->refclk);
+	}
+
+	if (!of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
+		phy->wkupclk = devm_clk_get(dev, "wkupclk");
+		if (IS_ERR(phy->wkupclk)) {
+			dev_err(dev, "unable to get wkupclk\n");
+			return PTR_ERR(phy->wkupclk);
+		}
+	} else {
+		phy->wkupclk = ERR_PTR(-ENODEV);
+	}
+
+	if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie") ||
+	    phy->phy_power_syscon) {
+		phy->sys_clk = devm_clk_get(dev, "sysclk");
+		if (IS_ERR(phy->sys_clk)) {
+			dev_err(dev, "unable to get sysclk\n");
+			return -EINVAL;
+		}
+	}
+
+	if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
+		clk = devm_clk_get(dev, "dpll_ref");
+		if (IS_ERR(clk)) {
+			dev_err(dev, "unable to get dpll ref clk\n");
+			return PTR_ERR(clk);
+		}
+		clk_set_rate(clk, 1500000000);
+
+		clk = devm_clk_get(dev, "dpll_ref_m2");
+		if (IS_ERR(clk)) {
+			dev_err(dev, "unable to get dpll ref m2 clk\n");
+			return PTR_ERR(clk);
+		}
+		clk_set_rate(clk, 100000000);
+
+		clk = devm_clk_get(dev, "phy-div");
+		if (IS_ERR(clk)) {
+			dev_err(dev, "unable to get phy-div clk\n");
+			return PTR_ERR(clk);
+		}
+		clk_set_rate(clk, 100000000);
+
+		phy->div_clk = devm_clk_get(dev, "div-clk");
+		if (IS_ERR(phy->div_clk)) {
+			dev_err(dev, "unable to get div-clk\n");
+			return PTR_ERR(phy->div_clk);
+		}
+	} else {
+		phy->div_clk = ERR_PTR(-ENODEV);
+	}
+
+	return 0;
+}
+
+static int ti_pipe3_get_sysctrl(struct ti_pipe3 *phy)
+{
+	struct device *dev = phy->dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *control_node;
+	struct platform_device *control_pdev;
+
+	phy->phy_power_syscon = syscon_regmap_lookup_by_phandle(node,
+							"syscon-phy-power");
+	if (IS_ERR(phy->phy_power_syscon)) {
+		dev_dbg(dev,
+			"can't get syscon-phy-power, using control device\n");
+		phy->phy_power_syscon = NULL;
+	} else {
+		if (of_property_read_u32_index(node,
+					       "syscon-phy-power", 1,
+					       &phy->power_reg)) {
+			dev_err(dev, "couldn't get power reg. offset\n");
+			return -EINVAL;
+		}
+	}
+
+	if (!phy->phy_power_syscon) {
+		control_node = of_parse_phandle(node, "ctrl-module", 0);
+		if (!control_node) {
+			dev_err(dev, "Failed to get control device phandle\n");
+			return -EINVAL;
+		}
+
+		control_pdev = of_find_device_by_node(control_node);
+		if (!control_pdev) {
+			dev_err(dev, "Failed to get control device\n");
+			return -EINVAL;
+		}
+
+		phy->control_dev = &control_pdev->dev;
+	}
+
+	if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
+		phy->pcs_syscon = syscon_regmap_lookup_by_phandle(node,
+								  "syscon-pcs");
+		if (IS_ERR(phy->pcs_syscon)) {
+			dev_dbg(dev,
+				"can't get syscon-pcs, using omap control\n");
+			phy->pcs_syscon = NULL;
+		} else {
+			if (of_property_read_u32_index(node,
+						       "syscon-pcs", 1,
+						       &phy->pcie_pcs_reg)) {
+				dev_err(dev,
+					"couldn't get pcie pcs reg. offset\n");
+				return -EINVAL;
+			}
+		}
+	}
+
+	if (of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
+		phy->dpll_reset_syscon = syscon_regmap_lookup_by_phandle(node,
+							"syscon-pllreset");
+		if (IS_ERR(phy->dpll_reset_syscon)) {
+			dev_info(dev,
+				 "can't get syscon-pllreset, sata dpll won't idle\n");
+			phy->dpll_reset_syscon = NULL;
+		} else {
+			if (of_property_read_u32_index(node,
+						       "syscon-pllreset", 1,
+						       &phy->dpll_reset_reg)) {
+				dev_err(dev,
+					"couldn't get pllreset reg. offset\n");
+				return -EINVAL;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy)
+{
+	struct resource *res;
+	struct device *dev = phy->dev;
+	struct device_node *node = dev->of_node;
+	struct platform_device *pdev = to_platform_device(dev);
+
+	if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie"))
+		return 0;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					   "phy_rx");
+	phy->phy_rx = devm_ioremap_resource(dev, res);
+	if (IS_ERR(phy->phy_rx))
+		return PTR_ERR(phy->phy_rx);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					   "phy_tx");
+	phy->phy_tx = devm_ioremap_resource(dev, res);
+
+	return PTR_ERR_OR_ZERO(phy->phy_tx);
+}
+
+static int ti_pipe3_get_pll_base(struct ti_pipe3 *phy)
+{
+	struct resource *res;
+	const struct of_device_id *match;
+	struct device *dev = phy->dev;
+	struct device_node *node = dev->of_node;
+	struct platform_device *pdev = to_platform_device(dev);
+
+	if (of_device_is_compatible(node, "ti,phy-pipe3-pcie"))
+		return 0;
+
+	match = of_match_device(ti_pipe3_id_table, dev);
+	if (!match)
+		return -EINVAL;
+
+	phy->dpll_map = (struct pipe3_dpll_map *)match->data;
+	if (!phy->dpll_map) {
+		dev_err(dev, "no DPLL data\n");
+		return -EINVAL;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					   "pll_ctrl");
+	phy->pll_ctrl_base = devm_ioremap_resource(dev, res);
+	return PTR_ERR_OR_ZERO(phy->pll_ctrl_base);
+}
+
+static int ti_pipe3_probe(struct platform_device *pdev)
+{
+	struct ti_pipe3 *phy;
+	struct phy *generic_phy;
+	struct phy_provider *phy_provider;
+	struct device_node *node = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	phy->dev		= dev;
+
+	ret = ti_pipe3_get_pll_base(phy);
+	if (ret)
+		return ret;
+
+	ret = ti_pipe3_get_tx_rx_base(phy);
+	if (ret)
+		return ret;
+
+	ret = ti_pipe3_get_sysctrl(phy);
+	if (ret)
+		return ret;
+
+	ret = ti_pipe3_get_clk(phy);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, phy);
+	pm_runtime_enable(dev);
+
+	/*
+	 * Prevent auto-disable of refclk for SATA PHY due to Errata i783
+	 */
+	if (of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
+		if (!IS_ERR(phy->refclk)) {
+			clk_prepare_enable(phy->refclk);
+			phy->sata_refclk_enabled = true;
+		}
+	}
+
+	generic_phy = devm_phy_create(dev, NULL, &ops);
+	if (IS_ERR(generic_phy))
+		return PTR_ERR(generic_phy);
+
+	phy_set_drvdata(generic_phy, phy);
+
+	ti_pipe3_power_off(generic_phy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static int ti_pipe3_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+
+	return 0;
+}
+
+static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy)
+{
+	int ret = 0;
+
+	if (!IS_ERR(phy->refclk)) {
+		ret = clk_prepare_enable(phy->refclk);
+		if (ret) {
+			dev_err(phy->dev, "Failed to enable refclk %d\n", ret);
+			return ret;
+		}
+	}
+
+	if (!IS_ERR(phy->wkupclk)) {
+		ret = clk_prepare_enable(phy->wkupclk);
+		if (ret) {
+			dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
+			goto disable_refclk;
+		}
+	}
+
+	if (!IS_ERR(phy->div_clk)) {
+		ret = clk_prepare_enable(phy->div_clk);
+		if (ret) {
+			dev_err(phy->dev, "Failed to enable div_clk %d\n", ret);
+			goto disable_wkupclk;
+		}
+	}
+
+	return 0;
+
+disable_wkupclk:
+	if (!IS_ERR(phy->wkupclk))
+		clk_disable_unprepare(phy->wkupclk);
+
+disable_refclk:
+	if (!IS_ERR(phy->refclk))
+		clk_disable_unprepare(phy->refclk);
+
+	return ret;
+}
+
+static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy)
+{
+	if (!IS_ERR(phy->wkupclk))
+		clk_disable_unprepare(phy->wkupclk);
+	if (!IS_ERR(phy->refclk)) {
+		clk_disable_unprepare(phy->refclk);
+		/*
+		 * SATA refclk needs an additional disable as we left it
+		 * on in probe to avoid Errata i783
+		 */
+		if (phy->sata_refclk_enabled) {
+			clk_disable_unprepare(phy->refclk);
+			phy->sata_refclk_enabled = false;
+		}
+	}
+
+	if (!IS_ERR(phy->div_clk))
+		clk_disable_unprepare(phy->div_clk);
+}
+
+static const struct of_device_id ti_pipe3_id_table[] = {
+	{
+		.compatible = "ti,phy-usb3",
+		.data = dpll_map_usb,
+	},
+	{
+		.compatible = "ti,omap-usb3",
+		.data = dpll_map_usb,
+	},
+	{
+		.compatible = "ti,phy-pipe3-sata",
+		.data = dpll_map_sata,
+	},
+	{
+		.compatible = "ti,phy-pipe3-pcie",
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, ti_pipe3_id_table);
+
+static struct platform_driver ti_pipe3_driver = {
+	.probe		= ti_pipe3_probe,
+	.remove		= ti_pipe3_remove,
+	.driver		= {
+		.name	= "ti-pipe3",
+		.of_match_table = ti_pipe3_id_table,
+	},
+};
+
+module_platform_driver(ti_pipe3_driver);
+
+MODULE_ALIAS("platform:ti_pipe3");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("TI PIPE3 phy driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/ti/phy-tusb1210.c b/drivers/phy/ti/phy-tusb1210.c
new file mode 100644
index 000000000..b8ec39ac4
--- /dev/null
+++ b/drivers/phy/ti/phy-tusb1210.c
@@ -0,0 +1,182 @@
+/**
+ * tusb1210.c - TUSB1210 USB ULPI PHY driver
+ *
+ * Copyright (C) 2015 Intel Corporation
+ *
+ * Author: Heikki Krogerus <heikki.krogerus@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/gpio/consumer.h>
+#include <linux/phy/ulpi_phy.h>
+
+#define TUSB1210_VENDOR_SPECIFIC2		0x80
+#define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT	0
+#define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT	4
+#define TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT	6
+
+struct tusb1210 {
+	struct ulpi *ulpi;
+	struct phy *phy;
+	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_cs;
+	u8 vendor_specific2;
+};
+
+static int tusb1210_power_on(struct phy *phy)
+{
+	struct tusb1210 *tusb = phy_get_drvdata(phy);
+
+	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
+	gpiod_set_value_cansleep(tusb->gpio_cs, 1);
+
+	/* Restore the optional eye diagram optimization value */
+	if (tusb->vendor_specific2)
+		ulpi_write(tusb->ulpi, TUSB1210_VENDOR_SPECIFIC2,
+			   tusb->vendor_specific2);
+
+	return 0;
+}
+
+static int tusb1210_power_off(struct phy *phy)
+{
+	struct tusb1210 *tusb = phy_get_drvdata(phy);
+
+	gpiod_set_value_cansleep(tusb->gpio_reset, 0);
+	gpiod_set_value_cansleep(tusb->gpio_cs, 0);
+
+	return 0;
+}
+
+static int tusb1210_set_mode(struct phy *phy, enum phy_mode mode)
+{
+	struct tusb1210 *tusb = phy_get_drvdata(phy);
+	int ret;
+
+	ret = ulpi_read(tusb->ulpi, ULPI_OTG_CTRL);
+	if (ret < 0)
+		return ret;
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:
+		ret |= (ULPI_OTG_CTRL_DRVVBUS_EXT
+			| ULPI_OTG_CTRL_ID_PULLUP
+			| ULPI_OTG_CTRL_DP_PULLDOWN
+			| ULPI_OTG_CTRL_DM_PULLDOWN);
+		ulpi_write(tusb->ulpi, ULPI_OTG_CTRL, ret);
+		ret |= ULPI_OTG_CTRL_DRVVBUS;
+		break;
+	case PHY_MODE_USB_DEVICE:
+		ret &= ~(ULPI_OTG_CTRL_DRVVBUS
+			 | ULPI_OTG_CTRL_DP_PULLDOWN
+			 | ULPI_OTG_CTRL_DM_PULLDOWN);
+		ulpi_write(tusb->ulpi, ULPI_OTG_CTRL, ret);
+		ret &= ~ULPI_OTG_CTRL_DRVVBUS_EXT;
+		break;
+	default:
+		/* nothing */
+		return 0;
+	}
+
+	return ulpi_write(tusb->ulpi, ULPI_OTG_CTRL, ret);
+}
+
+static const struct phy_ops phy_ops = {
+	.power_on = tusb1210_power_on,
+	.power_off = tusb1210_power_off,
+	.set_mode = tusb1210_set_mode,
+	.owner = THIS_MODULE,
+};
+
+static int tusb1210_probe(struct ulpi *ulpi)
+{
+	struct tusb1210 *tusb;
+	u8 val, reg;
+
+	tusb = devm_kzalloc(&ulpi->dev, sizeof(*tusb), GFP_KERNEL);
+	if (!tusb)
+		return -ENOMEM;
+
+	tusb->gpio_reset = devm_gpiod_get_optional(&ulpi->dev, "reset",
+						   GPIOD_OUT_LOW);
+	if (IS_ERR(tusb->gpio_reset))
+		return PTR_ERR(tusb->gpio_reset);
+
+	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
+
+	tusb->gpio_cs = devm_gpiod_get_optional(&ulpi->dev, "cs",
+						GPIOD_OUT_LOW);
+	if (IS_ERR(tusb->gpio_cs))
+		return PTR_ERR(tusb->gpio_cs);
+
+	gpiod_set_value_cansleep(tusb->gpio_cs, 1);
+
+	/*
+	 * VENDOR_SPECIFIC2 register in TUSB1210 can be used for configuring eye
+	 * diagram optimization and DP/DM swap.
+	 */
+
+	/* High speed output drive strength configuration */
+	device_property_read_u8(&ulpi->dev, "ihstx", &val);
+	reg = val << TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT;
+
+	/* High speed output impedance configuration */
+	device_property_read_u8(&ulpi->dev, "zhsdrv", &val);
+	reg |= val << TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT;
+
+	/* DP/DM swap control */
+	device_property_read_u8(&ulpi->dev, "datapolarity", &val);
+	reg |= val << TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT;
+
+	if (reg) {
+		ulpi_write(ulpi, TUSB1210_VENDOR_SPECIFIC2, reg);
+		tusb->vendor_specific2 = reg;
+	}
+
+	tusb->phy = ulpi_phy_create(ulpi, &phy_ops);
+	if (IS_ERR(tusb->phy))
+		return PTR_ERR(tusb->phy);
+
+	tusb->ulpi = ulpi;
+
+	phy_set_drvdata(tusb->phy, tusb);
+	ulpi_set_drvdata(ulpi, tusb);
+	return 0;
+}
+
+static void tusb1210_remove(struct ulpi *ulpi)
+{
+	struct tusb1210 *tusb = ulpi_get_drvdata(ulpi);
+
+	ulpi_phy_destroy(ulpi, tusb->phy);
+}
+
+#define TI_VENDOR_ID 0x0451
+
+static const struct ulpi_device_id tusb1210_ulpi_id[] = {
+	{ TI_VENDOR_ID, 0x1507, },  /* TUSB1210 */
+	{ TI_VENDOR_ID, 0x1508, },  /* TUSB1211 */
+	{ },
+};
+MODULE_DEVICE_TABLE(ulpi, tusb1210_ulpi_id);
+
+static struct ulpi_driver tusb1210_driver = {
+	.id_table = tusb1210_ulpi_id,
+	.probe = tusb1210_probe,
+	.remove = tusb1210_remove,
+	.driver = {
+		.name = "tusb1210",
+		.owner = THIS_MODULE,
+	},
+};
+
+module_ulpi_driver(tusb1210_driver);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TUSB1210 ULPI PHY driver");
diff --git a/drivers/phy/ti/phy-twl4030-usb.c b/drivers/phy/ti/phy-twl4030-usb.c
new file mode 100644
index 000000000..ea7564392
--- /dev/null
+++ b/drivers/phy/ti/phy-twl4030-usb.c
@@ -0,0 +1,868 @@
+/*
+ * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
+ *
+ * Copyright (C) 2004-2007 Texas Instruments
+ * Copyright (C) 2008 Nokia Corporation
+ * Contact: Felipe Balbi <felipe.balbi@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Current status:
+ *	- HS USB ULPI mode works.
+ *	- 3-pin mode support may be added in future.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/usb/otg.h>
+#include <linux/phy/phy.h>
+#include <linux/pm_runtime.h>
+#include <linux/usb/musb.h>
+#include <linux/usb/ulpi.h>
+#include <linux/mfd/twl.h>
+#include <linux/regulator/consumer.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+
+/* Register defines */
+
+#define MCPC_CTRL			0x30
+#define MCPC_CTRL_RTSOL			(1 << 7)
+#define MCPC_CTRL_EXTSWR		(1 << 6)
+#define MCPC_CTRL_EXTSWC		(1 << 5)
+#define MCPC_CTRL_VOICESW		(1 << 4)
+#define MCPC_CTRL_OUT64K		(1 << 3)
+#define MCPC_CTRL_RTSCTSSW		(1 << 2)
+#define MCPC_CTRL_HS_UART		(1 << 0)
+
+#define MCPC_IO_CTRL			0x33
+#define MCPC_IO_CTRL_MICBIASEN		(1 << 5)
+#define MCPC_IO_CTRL_CTS_NPU		(1 << 4)
+#define MCPC_IO_CTRL_RXD_PU		(1 << 3)
+#define MCPC_IO_CTRL_TXDTYP		(1 << 2)
+#define MCPC_IO_CTRL_CTSTYP		(1 << 1)
+#define MCPC_IO_CTRL_RTSTYP		(1 << 0)
+
+#define MCPC_CTRL2			0x36
+#define MCPC_CTRL2_MCPC_CK_EN		(1 << 0)
+
+#define OTHER_FUNC_CTRL			0x80
+#define OTHER_FUNC_CTRL_BDIS_ACON_EN	(1 << 4)
+#define OTHER_FUNC_CTRL_FIVEWIRE_MODE	(1 << 2)
+
+#define OTHER_IFC_CTRL			0x83
+#define OTHER_IFC_CTRL_OE_INT_EN	(1 << 6)
+#define OTHER_IFC_CTRL_CEA2011_MODE	(1 << 5)
+#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN	(1 << 4)
+#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT	(1 << 3)
+#define OTHER_IFC_CTRL_HIZ_ULPI		(1 << 2)
+#define OTHER_IFC_CTRL_ALT_INT_REROUTE	(1 << 0)
+
+#define OTHER_INT_EN_RISE		0x86
+#define OTHER_INT_EN_FALL		0x89
+#define OTHER_INT_STS			0x8C
+#define OTHER_INT_LATCH			0x8D
+#define OTHER_INT_VB_SESS_VLD		(1 << 7)
+#define OTHER_INT_DM_HI			(1 << 6) /* not valid for "latch" reg */
+#define OTHER_INT_DP_HI			(1 << 5) /* not valid for "latch" reg */
+#define OTHER_INT_BDIS_ACON		(1 << 3) /* not valid for "fall" regs */
+#define OTHER_INT_MANU			(1 << 1)
+#define OTHER_INT_ABNORMAL_STRESS	(1 << 0)
+
+#define ID_STATUS			0x96
+#define ID_RES_FLOAT			(1 << 4)
+#define ID_RES_440K			(1 << 3)
+#define ID_RES_200K			(1 << 2)
+#define ID_RES_102K			(1 << 1)
+#define ID_RES_GND			(1 << 0)
+
+#define POWER_CTRL			0xAC
+#define POWER_CTRL_OTG_ENAB		(1 << 5)
+
+#define OTHER_IFC_CTRL2			0xAF
+#define OTHER_IFC_CTRL2_ULPI_STP_LOW	(1 << 4)
+#define OTHER_IFC_CTRL2_ULPI_TXEN_POL	(1 << 3)
+#define OTHER_IFC_CTRL2_ULPI_4PIN_2430	(1 << 2)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK	(3 << 0) /* bits 0 and 1 */
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N	(0 << 0)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N	(1 << 0)
+
+#define REG_CTRL_EN			0xB2
+#define REG_CTRL_ERROR			0xB5
+#define ULPI_I2C_CONFLICT_INTEN		(1 << 0)
+
+#define OTHER_FUNC_CTRL2		0xB8
+#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN	(1 << 0)
+
+/* following registers do not have separate _clr and _set registers */
+#define VBUS_DEBOUNCE			0xC0
+#define ID_DEBOUNCE			0xC1
+#define VBAT_TIMER			0xD3
+#define PHY_PWR_CTRL			0xFD
+#define PHY_PWR_PHYPWD			(1 << 0)
+#define PHY_CLK_CTRL			0xFE
+#define PHY_CLK_CTRL_CLOCKGATING_EN	(1 << 2)
+#define PHY_CLK_CTRL_CLK32K_EN		(1 << 1)
+#define REQ_PHY_DPLL_CLK		(1 << 0)
+#define PHY_CLK_CTRL_STS		0xFF
+#define PHY_DPLL_CLK			(1 << 0)
+
+/* In module TWL_MODULE_PM_MASTER */
+#define STS_HW_CONDITIONS		0x0F
+
+/* In module TWL_MODULE_PM_RECEIVER */
+#define VUSB_DEDICATED1			0x7D
+#define VUSB_DEDICATED2			0x7E
+#define VUSB1V5_DEV_GRP			0x71
+#define VUSB1V5_TYPE			0x72
+#define VUSB1V5_REMAP			0x73
+#define VUSB1V8_DEV_GRP			0x74
+#define VUSB1V8_TYPE			0x75
+#define VUSB1V8_REMAP			0x76
+#define VUSB3V1_DEV_GRP			0x77
+#define VUSB3V1_TYPE			0x78
+#define VUSB3V1_REMAP			0x79
+
+/* In module TWL4030_MODULE_INTBR */
+#define PMBR1				0x0D
+#define GPIO_USB_4PIN_ULPI_2430C	(3 << 0)
+
+static irqreturn_t twl4030_usb_irq(int irq, void *_twl);
+/*
+ * If VBUS is valid or ID is ground, then we know a
+ * cable is present and we need to be runtime-enabled
+ */
+static inline bool cable_present(enum musb_vbus_id_status stat)
+{
+	return stat == MUSB_VBUS_VALID ||
+		stat == MUSB_ID_GROUND;
+}
+
+struct twl4030_usb {
+	struct usb_phy		phy;
+	struct device		*dev;
+
+	/* TWL4030 internal USB regulator supplies */
+	struct regulator	*usb1v5;
+	struct regulator	*usb1v8;
+	struct regulator	*usb3v1;
+
+	/* for vbus reporting with irqs disabled */
+	struct mutex		lock;
+
+	/* pin configuration */
+	enum twl4030_usb_mode	usb_mode;
+
+	int			irq;
+	enum musb_vbus_id_status linkstat;
+	bool			vbus_supplied;
+	bool			musb_mailbox_pending;
+
+	struct delayed_work	id_workaround_work;
+};
+
+/* internal define on top of container_of */
+#define phy_to_twl(x)		container_of((x), struct twl4030_usb, phy)
+
+/*-------------------------------------------------------------------------*/
+
+static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
+		u8 module, u8 data, u8 address)
+{
+	u8 check = 0xFF;
+
+	if ((twl_i2c_write_u8(module, data, address) >= 0) &&
+	    (twl_i2c_read_u8(module, &check, address) >= 0) &&
+						(check == data))
+		return 0;
+	dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
+			1, module, address, check, data);
+
+	/* Failed once: Try again */
+	if ((twl_i2c_write_u8(module, data, address) >= 0) &&
+	    (twl_i2c_read_u8(module, &check, address) >= 0) &&
+						(check == data))
+		return 0;
+	dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
+			2, module, address, check, data);
+
+	/* Failed again: Return error */
+	return -EBUSY;
+}
+
+#define twl4030_usb_write_verify(twl, address, data)	\
+	twl4030_i2c_write_u8_verify(twl, TWL_MODULE_USB, (data), (address))
+
+static inline int twl4030_usb_write(struct twl4030_usb *twl,
+		u8 address, u8 data)
+{
+	int ret = 0;
+
+	ret = twl_i2c_write_u8(TWL_MODULE_USB, data, address);
+	if (ret < 0)
+		dev_dbg(twl->dev,
+			"TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
+	return ret;
+}
+
+static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
+{
+	u8 data;
+	int ret = 0;
+
+	ret = twl_i2c_read_u8(module, &data, address);
+	if (ret >= 0)
+		ret = data;
+	else
+		dev_dbg(twl->dev,
+			"TWL4030:readb[0x%x,0x%x] Error %d\n",
+					module, address, ret);
+
+	return ret;
+}
+
+static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
+{
+	return twl4030_readb(twl, TWL_MODULE_USB, address);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static inline int
+twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
+{
+	return twl4030_usb_write(twl, ULPI_SET(reg), bits);
+}
+
+static inline int
+twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
+{
+	return twl4030_usb_write(twl, ULPI_CLR(reg), bits);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static bool twl4030_is_driving_vbus(struct twl4030_usb *twl)
+{
+	int ret;
+
+	ret = twl4030_usb_read(twl, PHY_CLK_CTRL_STS);
+	if (ret < 0 || !(ret & PHY_DPLL_CLK))
+		/*
+		 * if clocks are off, registers are not updated,
+		 * but we can assume we don't drive VBUS in this case
+		 */
+		return false;
+
+	ret = twl4030_usb_read(twl, ULPI_OTG_CTRL);
+	if (ret < 0)
+		return false;
+
+	return (ret & (ULPI_OTG_DRVVBUS | ULPI_OTG_CHRGVBUS)) ? true : false;
+}
+
+static enum musb_vbus_id_status
+	twl4030_usb_linkstat(struct twl4030_usb *twl)
+{
+	int	status;
+	enum musb_vbus_id_status linkstat = MUSB_UNKNOWN;
+
+	twl->vbus_supplied = false;
+
+	/*
+	 * For ID/VBUS sensing, see manual section 15.4.8 ...
+	 * except when using only battery backup power, two
+	 * comparators produce VBUS_PRES and ID_PRES signals,
+	 * which don't match docs elsewhere.  But ... BIT(7)
+	 * and BIT(2) of STS_HW_CONDITIONS, respectively, do
+	 * seem to match up.  If either is true the USB_PRES
+	 * signal is active, the OTG module is activated, and
+	 * its interrupt may be raised (may wake the system).
+	 */
+	status = twl4030_readb(twl, TWL_MODULE_PM_MASTER, STS_HW_CONDITIONS);
+	if (status < 0)
+		dev_err(twl->dev, "USB link status err %d\n", status);
+	else if (status & (BIT(7) | BIT(2))) {
+		if (status & BIT(7)) {
+			if (twl4030_is_driving_vbus(twl))
+				status &= ~BIT(7);
+			else
+				twl->vbus_supplied = true;
+		}
+
+		if (status & BIT(2))
+			linkstat = MUSB_ID_GROUND;
+		else if (status & BIT(7))
+			linkstat = MUSB_VBUS_VALID;
+		else
+			linkstat = MUSB_VBUS_OFF;
+	} else {
+		if (twl->linkstat != MUSB_UNKNOWN)
+			linkstat = MUSB_VBUS_OFF;
+	}
+
+	kobject_uevent(&twl->dev->kobj, linkstat == MUSB_VBUS_VALID
+					? KOBJ_ONLINE : KOBJ_OFFLINE);
+
+	dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
+			status, status, linkstat);
+
+	/* REVISIT this assumes host and peripheral controllers
+	 * are registered, and that both are active...
+	 */
+
+	return linkstat;
+}
+
+static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
+{
+	twl->usb_mode = mode;
+
+	switch (mode) {
+	case T2_USB_MODE_ULPI:
+		twl4030_usb_clear_bits(twl, ULPI_IFC_CTRL,
+					ULPI_IFC_CTRL_CARKITMODE);
+		twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
+		twl4030_usb_clear_bits(twl, ULPI_FUNC_CTRL,
+					ULPI_FUNC_CTRL_XCVRSEL_MASK |
+					ULPI_FUNC_CTRL_OPMODE_MASK);
+		break;
+	case -1:
+		/* FIXME: power on defaults */
+		break;
+	default:
+		dev_err(twl->dev, "unsupported T2 transceiver mode %d\n",
+				mode);
+		break;
+	}
+}
+
+static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
+{
+	unsigned long timeout;
+	int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
+
+	if (val >= 0) {
+		if (on) {
+			/* enable DPLL to access PHY registers over I2C */
+			val |= REQ_PHY_DPLL_CLK;
+			WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
+						(u8)val) < 0);
+
+			timeout = jiffies + HZ;
+			while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
+							PHY_DPLL_CLK)
+				&& time_before(jiffies, timeout))
+					udelay(10);
+			if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
+							PHY_DPLL_CLK))
+				dev_err(twl->dev, "Timeout setting T2 HSUSB "
+						"PHY DPLL clock\n");
+		} else {
+			/* let ULPI control the DPLL clock */
+			val &= ~REQ_PHY_DPLL_CLK;
+			WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
+						(u8)val) < 0);
+		}
+	}
+}
+
+static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
+{
+	u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
+
+	if (on)
+		pwr &= ~PHY_PWR_PHYPWD;
+	else
+		pwr |= PHY_PWR_PHYPWD;
+
+	WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
+}
+
+static int __maybe_unused twl4030_usb_suspend(struct device *dev)
+{
+	struct twl4030_usb *twl = dev_get_drvdata(dev);
+
+	/*
+	 * we need enabled runtime on resume,
+	 * so turn irq off here, so we do not get it early
+	 * note: wakeup on usb plug works independently of this
+	 */
+	dev_dbg(twl->dev, "%s\n", __func__);
+	disable_irq(twl->irq);
+
+	return 0;
+}
+
+static int __maybe_unused twl4030_usb_resume(struct device *dev)
+{
+	struct twl4030_usb *twl = dev_get_drvdata(dev);
+
+	dev_dbg(twl->dev, "%s\n", __func__);
+	enable_irq(twl->irq);
+	/* check whether cable status changed */
+	twl4030_usb_irq(0, twl);
+
+	return 0;
+}
+
+static int __maybe_unused twl4030_usb_runtime_suspend(struct device *dev)
+{
+	struct twl4030_usb *twl = dev_get_drvdata(dev);
+
+	dev_dbg(twl->dev, "%s\n", __func__);
+
+	__twl4030_phy_power(twl, 0);
+	regulator_disable(twl->usb1v5);
+	regulator_disable(twl->usb1v8);
+	regulator_disable(twl->usb3v1);
+
+	return 0;
+}
+
+static int __maybe_unused twl4030_usb_runtime_resume(struct device *dev)
+{
+	struct twl4030_usb *twl = dev_get_drvdata(dev);
+	int res;
+
+	dev_dbg(twl->dev, "%s\n", __func__);
+
+	res = regulator_enable(twl->usb3v1);
+	if (res)
+		dev_err(twl->dev, "Failed to enable usb3v1\n");
+
+	res = regulator_enable(twl->usb1v8);
+	if (res)
+		dev_err(twl->dev, "Failed to enable usb1v8\n");
+
+	/*
+	 * Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
+	 * in twl4030) resets the VUSB_DEDICATED2 register. This reset
+	 * enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
+	 * SLEEP. We work around this by clearing the bit after usv3v1
+	 * is re-activated. This ensures that VUSB3V1 is really active.
+	 */
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
+
+	res = regulator_enable(twl->usb1v5);
+	if (res)
+		dev_err(twl->dev, "Failed to enable usb1v5\n");
+
+	__twl4030_phy_power(twl, 1);
+	twl4030_usb_write(twl, PHY_CLK_CTRL,
+			  twl4030_usb_read(twl, PHY_CLK_CTRL) |
+			  (PHY_CLK_CTRL_CLOCKGATING_EN |
+			   PHY_CLK_CTRL_CLK32K_EN));
+
+	twl4030_i2c_access(twl, 1);
+	twl4030_usb_set_mode(twl, twl->usb_mode);
+	if (twl->usb_mode == T2_USB_MODE_ULPI)
+		twl4030_i2c_access(twl, 0);
+	/*
+	 * According to the TPS65950 TRM, there has to be at least 50ms
+	 * delay between setting POWER_CTRL_OTG_ENAB and enabling charging
+	 * so wait here so that a fully enabled phy can be expected after
+	 * resume
+	 */
+	msleep(50);
+	return 0;
+}
+
+static int twl4030_phy_power_off(struct phy *phy)
+{
+	struct twl4030_usb *twl = phy_get_drvdata(phy);
+
+	dev_dbg(twl->dev, "%s\n", __func__);
+
+	return 0;
+}
+
+static int twl4030_phy_power_on(struct phy *phy)
+{
+	struct twl4030_usb *twl = phy_get_drvdata(phy);
+
+	dev_dbg(twl->dev, "%s\n", __func__);
+	pm_runtime_get_sync(twl->dev);
+	schedule_delayed_work(&twl->id_workaround_work, HZ);
+	pm_runtime_mark_last_busy(twl->dev);
+	pm_runtime_put_autosuspend(twl->dev);
+
+	return 0;
+}
+
+static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
+{
+	/* Enable writing to power configuration registers */
+	twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
+			 TWL4030_PM_MASTER_PROTECT_KEY);
+
+	twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
+			 TWL4030_PM_MASTER_PROTECT_KEY);
+
+	/* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
+	/*twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
+
+	/* input to VUSB3V1 LDO is from VBAT, not VBUS */
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
+
+	/* Initialize 3.1V regulator */
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
+
+	twl->usb3v1 = devm_regulator_get(twl->dev, "usb3v1");
+	if (IS_ERR(twl->usb3v1))
+		return -ENODEV;
+
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
+
+	/* Initialize 1.5V regulator */
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
+
+	twl->usb1v5 = devm_regulator_get(twl->dev, "usb1v5");
+	if (IS_ERR(twl->usb1v5))
+		return -ENODEV;
+
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
+
+	/* Initialize 1.8V regulator */
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
+
+	twl->usb1v8 = devm_regulator_get(twl->dev, "usb1v8");
+	if (IS_ERR(twl->usb1v8))
+		return -ENODEV;
+
+	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
+
+	/* disable access to power configuration registers */
+	twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
+			 TWL4030_PM_MASTER_PROTECT_KEY);
+
+	return 0;
+}
+
+static ssize_t twl4030_usb_vbus_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct twl4030_usb *twl = dev_get_drvdata(dev);
+	int ret = -EINVAL;
+
+	mutex_lock(&twl->lock);
+	ret = sprintf(buf, "%s\n",
+			twl->vbus_supplied ? "on" : "off");
+	mutex_unlock(&twl->lock);
+
+	return ret;
+}
+static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
+
+static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
+{
+	struct twl4030_usb *twl = _twl;
+	enum musb_vbus_id_status status;
+	bool status_changed = false;
+	int err;
+
+	status = twl4030_usb_linkstat(twl);
+
+	mutex_lock(&twl->lock);
+	if (status >= 0 && status != twl->linkstat) {
+		status_changed =
+			cable_present(twl->linkstat) !=
+			cable_present(status);
+		twl->linkstat = status;
+	}
+	mutex_unlock(&twl->lock);
+
+	if (status_changed) {
+		/* FIXME add a set_power() method so that B-devices can
+		 * configure the charger appropriately.  It's not always
+		 * correct to consume VBUS power, and how much current to
+		 * consume is a function of the USB configuration chosen
+		 * by the host.
+		 *
+		 * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
+		 * its disconnect() sibling, when changing to/from the
+		 * USB_LINK_VBUS state.  musb_hdrc won't care until it
+		 * starts to handle softconnect right.
+		 */
+		if (cable_present(status)) {
+			pm_runtime_get_sync(twl->dev);
+		} else {
+			pm_runtime_mark_last_busy(twl->dev);
+			pm_runtime_put_autosuspend(twl->dev);
+		}
+		twl->musb_mailbox_pending = true;
+	}
+	if (twl->musb_mailbox_pending) {
+		err = musb_mailbox(status);
+		if (!err)
+			twl->musb_mailbox_pending = false;
+	}
+
+	/* don't schedule during sleep - irq works right then */
+	if (status == MUSB_ID_GROUND && pm_runtime_active(twl->dev)) {
+		cancel_delayed_work(&twl->id_workaround_work);
+		schedule_delayed_work(&twl->id_workaround_work, HZ);
+	}
+
+	if (irq)
+		sysfs_notify(&twl->dev->kobj, NULL, "vbus");
+
+	return IRQ_HANDLED;
+}
+
+static void twl4030_id_workaround_work(struct work_struct *work)
+{
+	struct twl4030_usb *twl = container_of(work, struct twl4030_usb,
+		id_workaround_work.work);
+
+	twl4030_usb_irq(0, twl);
+}
+
+static int twl4030_phy_init(struct phy *phy)
+{
+	struct twl4030_usb *twl = phy_get_drvdata(phy);
+
+	pm_runtime_get_sync(twl->dev);
+	twl->linkstat = MUSB_UNKNOWN;
+	schedule_delayed_work(&twl->id_workaround_work, HZ);
+	pm_runtime_mark_last_busy(twl->dev);
+	pm_runtime_put_autosuspend(twl->dev);
+
+	return 0;
+}
+
+static int twl4030_set_peripheral(struct usb_otg *otg,
+					struct usb_gadget *gadget)
+{
+	if (!otg)
+		return -ENODEV;
+
+	otg->gadget = gadget;
+	if (!gadget)
+		otg->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int twl4030_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	if (!otg)
+		return -ENODEV;
+
+	otg->host = host;
+	if (!host)
+		otg->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static const struct phy_ops ops = {
+	.init		= twl4030_phy_init,
+	.power_on	= twl4030_phy_power_on,
+	.power_off	= twl4030_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static const struct dev_pm_ops twl4030_usb_pm_ops = {
+	SET_RUNTIME_PM_OPS(twl4030_usb_runtime_suspend,
+			   twl4030_usb_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(twl4030_usb_suspend, twl4030_usb_resume)
+};
+
+static int twl4030_usb_probe(struct platform_device *pdev)
+{
+	struct twl4030_usb_data *pdata = dev_get_platdata(&pdev->dev);
+	struct twl4030_usb	*twl;
+	struct phy		*phy;
+	int			status, err;
+	struct usb_otg		*otg;
+	struct device_node	*np = pdev->dev.of_node;
+	struct phy_provider	*phy_provider;
+
+	twl = devm_kzalloc(&pdev->dev, sizeof(*twl), GFP_KERNEL);
+	if (!twl)
+		return -ENOMEM;
+
+	if (np)
+		of_property_read_u32(np, "usb_mode",
+				(enum twl4030_usb_mode *)&twl->usb_mode);
+	else if (pdata) {
+		twl->usb_mode = pdata->usb_mode;
+	} else {
+		dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
+		return -EINVAL;
+	}
+
+	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
+	if (!otg)
+		return -ENOMEM;
+
+	twl->dev		= &pdev->dev;
+	twl->irq		= platform_get_irq(pdev, 0);
+	twl->vbus_supplied	= false;
+	twl->linkstat		= MUSB_UNKNOWN;
+	twl->musb_mailbox_pending = false;
+
+	twl->phy.dev		= twl->dev;
+	twl->phy.label		= "twl4030";
+	twl->phy.otg		= otg;
+	twl->phy.type		= USB_PHY_TYPE_USB2;
+
+	otg->usb_phy		= &twl->phy;
+	otg->set_host		= twl4030_set_host;
+	otg->set_peripheral	= twl4030_set_peripheral;
+
+	phy = devm_phy_create(twl->dev, NULL, &ops);
+	if (IS_ERR(phy)) {
+		dev_dbg(&pdev->dev, "Failed to create PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_set_drvdata(phy, twl);
+
+	phy_provider = devm_of_phy_provider_register(twl->dev,
+		of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return PTR_ERR(phy_provider);
+
+	/* init mutex for workqueue */
+	mutex_init(&twl->lock);
+
+	INIT_DELAYED_WORK(&twl->id_workaround_work, twl4030_id_workaround_work);
+
+	err = twl4030_usb_ldo_init(twl);
+	if (err) {
+		dev_err(&pdev->dev, "ldo init failed\n");
+		return err;
+	}
+	usb_add_phy_dev(&twl->phy);
+
+	platform_set_drvdata(pdev, twl);
+	if (device_create_file(&pdev->dev, &dev_attr_vbus))
+		dev_warn(&pdev->dev, "could not create sysfs file\n");
+
+	ATOMIC_INIT_NOTIFIER_HEAD(&twl->phy.notifier);
+
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, 2000);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_get_sync(&pdev->dev);
+
+	/* Our job is to use irqs and status from the power module
+	 * to keep the transceiver disabled when nothing's connected.
+	 *
+	 * FIXME we actually shouldn't start enabling it until the
+	 * USB controller drivers have said they're ready, by calling
+	 * set_host() and/or set_peripheral() ... OTG_capable boards
+	 * need both handles, otherwise just one suffices.
+	 */
+	status = devm_request_threaded_irq(twl->dev, twl->irq, NULL,
+			twl4030_usb_irq, IRQF_TRIGGER_FALLING |
+			IRQF_TRIGGER_RISING | IRQF_ONESHOT, "twl4030_usb", twl);
+	if (status < 0) {
+		dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
+			twl->irq, status);
+		return status;
+	}
+
+	if (pdata)
+		err = phy_create_lookup(phy, "usb", "musb-hdrc.0");
+	if (err)
+		return err;
+
+	pm_runtime_mark_last_busy(&pdev->dev);
+	pm_runtime_put_autosuspend(twl->dev);
+
+	dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
+	return 0;
+}
+
+static int twl4030_usb_remove(struct platform_device *pdev)
+{
+	struct twl4030_usb *twl = platform_get_drvdata(pdev);
+	int val;
+
+	usb_remove_phy(&twl->phy);
+	pm_runtime_get_sync(twl->dev);
+	cancel_delayed_work_sync(&twl->id_workaround_work);
+	device_remove_file(twl->dev, &dev_attr_vbus);
+
+	/* set transceiver mode to power on defaults */
+	twl4030_usb_set_mode(twl, -1);
+
+	/* idle ulpi before powering off */
+	if (cable_present(twl->linkstat))
+		pm_runtime_put_noidle(twl->dev);
+	pm_runtime_mark_last_busy(twl->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	pm_runtime_put_sync(twl->dev);
+	pm_runtime_disable(twl->dev);
+
+	/* autogate 60MHz ULPI clock,
+	 * clear dpll clock request for i2c access,
+	 * disable 32KHz
+	 */
+	val = twl4030_usb_read(twl, PHY_CLK_CTRL);
+	if (val >= 0) {
+		val |= PHY_CLK_CTRL_CLOCKGATING_EN;
+		val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
+		twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
+	}
+
+	/* disable complete OTG block */
+	twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id twl4030_usb_id_table[] = {
+	{ .compatible = "ti,twl4030-usb" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
+#endif
+
+static struct platform_driver twl4030_usb_driver = {
+	.probe		= twl4030_usb_probe,
+	.remove		= twl4030_usb_remove,
+	.driver		= {
+		.name	= "twl4030_usb",
+		.pm	= &twl4030_usb_pm_ops,
+		.of_match_table = of_match_ptr(twl4030_usb_id_table),
+	},
+};
+
+static int __init twl4030_usb_init(void)
+{
+	return platform_driver_register(&twl4030_usb_driver);
+}
+subsys_initcall(twl4030_usb_init);
+
+static void __exit twl4030_usb_exit(void)
+{
+	platform_driver_unregister(&twl4030_usb_driver);
+}
+module_exit(twl4030_usb_exit);
+
+MODULE_ALIAS("platform:twl4030_usb");
+MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
+MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
+MODULE_LICENSE("GPL");