diff options
Diffstat (limited to 'Documentation/devicetree/bindings/connector')
| -rw-r--r-- | Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt | 49 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/connector/usb-connector.txt | 119 |
2 files changed, 168 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt b/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt new file mode 100644 index 000000000..22256e295 --- /dev/null +++ b/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt @@ -0,0 +1,49 @@ +Samsung micro-USB 11-pin connector +================================== + +Samsung micro-USB 11-pin connector is an extension of micro-USB connector. +It is present in multiple Samsung mobile devices. +It has additional pins to route MHL traffic simultanously with USB. + +The bindings are superset of usb-connector bindings for micro-USB connector[1]. + +Required properties: +- compatible: must be: "samsung,usb-connector-11pin", "usb-b-connector", +- type: must be "micro". + +Required nodes: +- any data bus to the connector should be modeled using the OF graph bindings + specified in bindings/graph.txt, unless the bus is between parent node and + the connector. Since single connector can have multpile data buses every bus + has assigned OF graph port number as follows: + 0: High Speed (HS), + 3: Mobile High-Definition Link (MHL), specific to 11-pin Samsung micro-USB. + +[1]: bindings/connector/usb-connector.txt + +Example +------- + +Micro-USB connector with HS lines routed via controller (MUIC) and MHL lines +connected to HDMI-MHL bridge (sii8620): + +muic-max77843@66 { + ... + usb_con: connector { + compatible = "samsung,usb-connector-11pin", "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@3 { + reg = <3>; + usb_con_mhl: endpoint { + remote-endpoint = <&sii8620_mhl>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt new file mode 100644 index 000000000..8855bfcfd --- /dev/null +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt @@ -0,0 +1,119 @@ +USB Connector +============= + +USB connector node represents physical USB connector. It should be +a child of USB interface controller. + +Required properties: +- compatible: describes type of the connector, must be one of: + "usb-a-connector", + "usb-b-connector", + "usb-c-connector". + +Optional properties: +- label: symbolic name for the connector, +- type: size of the connector, should be specified in case of USB-A, USB-B + non-fullsize connectors: "mini", "micro". + +Optional properties for usb-c-connector: +- power-role: should be one of "source", "sink" or "dual"(DRP) if typec + connector has power support. +- try-power-role: preferred power role if "dual"(DRP) can support Try.SNK + or Try.SRC, should be "sink" for Try.SNK or "source" for Try.SRC. +- data-role: should be one of "host", "device", "dual"(DRD) if typec + connector supports USB data. + +Required properties for usb-c-connector with power delivery support: +- source-pdos: An array of u32 with each entry providing supported power + source data object(PDO), the detailed bit definitions of PDO can be found + in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 + Source_Capabilities Message, the order of each entry(PDO) should follow + the PD spec chapter 6.4.1. Required for power source and power dual role. + User can specify the source PDO array via PDO_FIXED/BATT/VAR() defined in + dt-bindings/usb/pd.h. +- sink-pdos: An array of u32 with each entry providing supported power + sink data object(PDO), the detailed bit definitions of PDO can be found + in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 + Sink Capabilities Message, the order of each entry(PDO) should follow + the PD spec chapter 6.4.1. Required for power sink and power dual role. + User can specify the sink PDO array via PDO_FIXED/BATT/VAR() defined in + dt-bindings/usb/pd.h. +- op-sink-microwatt: Sink required operating power in microwatt, if source + can't offer the power, Capability Mismatch is set. Required for power + sink and power dual role. + +Required nodes: +- any data bus to the connector should be modeled using the OF graph bindings + specified in bindings/graph.txt, unless the bus is between parent node and + the connector. Since single connector can have multpile data buses every bus + has assigned OF graph port number as follows: + 0: High Speed (HS), present in all connectors, + 1: Super Speed (SS), present in SS capable connectors, + 2: Sideband use (SBU), present in USB-C. + +Examples +-------- + +1. Micro-USB connector with HS lines routed via controller (MUIC): + +muic-max77843@66 { + ... + usb_con: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; +}; + +2. USB-C connector attached to CC controller (s2mm005), HS lines routed +to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. +DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. + +ccic: s2mm005@33 { + ... + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + usb_con_hs: endpoint { + remote-endpoint = <&max77865_usbc_hs>; + }; + }; + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&usbdrd_phy_ss>; + }; + }; + port@2 { + reg = <2>; + usb_con_sbu: endpoint { + remote-endpoint = <&dp_aux>; + }; + }; + }; + }; +}; + +3. USB-C connector attached to a typec port controller(ptn5110), which has +power delivery support and enables drp. + +typec: ptn5110@50 { + ... + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 12000, 2000)>; + op-sink-microwatt = <10000000>; + }; +}; |