diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/dac/ad5592r.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/iio/dac/ad5592r.txt | 155 |
1 files changed, 155 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/dac/ad5592r.txt b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt new file mode 100644 index 000000000..989f96f31 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt @@ -0,0 +1,155 @@ +Analog Devices AD5592R/AD5593R DAC/ADC device driver + +Required properties for the AD5592R: + - compatible: Must be "adi,ad5592r" + - reg: SPI chip select number for the device + - spi-max-frequency: Max SPI frequency to use (< 30000000) + - spi-cpol: The AD5592R requires inverse clock polarity (CPOL) mode + +Required properties for the AD5593R: + - compatible: Must be "adi,ad5593r" + - reg: I2C address of the device + +Required properties for all supported chips: + - #address-cells: Should be 1. + - #size-cells: Should be 0. + - channel nodes: + Each child node represents one channel and has the following + Required properties: + * reg: Pin on which this channel is connected to. + * adi,mode: Mode or function of this channel. + Macros specifying the valid values + can be found in <dt-bindings/iio/adi,ad5592r.h>. + + The following values are currently supported: + * CH_MODE_UNUSED (the pin is unused) + * CH_MODE_ADC (the pin is ADC input) + * CH_MODE_DAC (the pin is DAC output) + * CH_MODE_DAC_AND_ADC (the pin is DAC output + but can be monitored by an ADC, since + there is no disadvantage this + this should be considered as the + preferred DAC mode) + * CH_MODE_GPIO (the pin is registered + with GPIOLIB) + Optional properties: + * adi,off-state: State of this channel when unused or the + device gets removed. Macros specifying the + valid values can be found in + <dt-bindings/iio/adi,ad5592r.h>. + + * CH_OFFSTATE_PULLDOWN (the pin is pulled down) + * CH_OFFSTATE_OUT_LOW (the pin is output low) + * CH_OFFSTATE_OUT_HIGH (the pin is output high) + * CH_OFFSTATE_OUT_TRISTATE (the pin is + tristated output) + + +Optional properties: + - vref-supply: Phandle to the external reference voltage supply. This should + only be set if there is an external reference voltage connected to the VREF + pin. If the property is not set the internal 2.5V reference is used. + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be + asserted during driver probe. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. + +AD5592R Example: + + #include <dt-bindings/iio/adi,ad5592r.h> + + vref: regulator-vref { + compatible = "regulator-fixed"; + regulator-name = "vref-ad559x"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ad5592r@0 { + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + compatible = "adi,ad5592r"; + reg = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + + vref-supply = <&vref>; /* optional */ + reset-gpios = <&gpio0 86 0>; /* optional */ + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = <CH_MODE_DAC>; + }; + channel@1 { + reg = <1>; + adi,mode = <CH_MODE_ADC>; + }; + channel@2 { + reg = <2>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + }; + channel@3 { + reg = <3>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@4 { + reg = <4>; + adi,mode = <CH_MODE_UNUSED>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@5 { + reg = <5>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@6 { + reg = <6>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@7 { + reg = <7>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + }; + +AD5593R Example: + + #include <dt-bindings/iio/adi,ad5592r.h> + + ad5593r@10 { + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + compatible = "adi,ad5593r"; + reg = <0x10>; + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = <CH_MODE_DAC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@1 { + reg = <1>; + adi,mode = <CH_MODE_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@2 { + reg = <2>; + adi,mode = <CH_MODE_DAC_AND_ADC>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + channel@6 { + reg = <6>; + adi,mode = <CH_MODE_GPIO>; + adi,off-state = <CH_OFFSTATE_PULLDOWN>; + }; + }; |