diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc/mtk-sd.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/mtk-sd.txt | 68 |
1 files changed, 68 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt new file mode 100644 index 000000000..f33467a54 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -0,0 +1,68 @@ +* MTK MMC controller + +The MTK MSDC can act as a MMC controller +to support MMC, SD, and SDIO types of memory cards. + +This file documents differences between the core properties in mmc.txt +and the properties used by the msdc driver. + +Required properties: +- compatible: value should be either of the following. + "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135 + "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 + "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 + "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 + "mediatek,mt7622-mmc": for MT7622 SoC + "mediatek,mt7623-mmc", "mediatek,mt2701-mmc": for MT7623 SoC + +- reg: physical base address of the controller and length +- interrupts: Should contain MSDC interrupt number +- clocks: Should contain phandle for the clock feeding the MMC controller +- clock-names: Should contain the following: + "source" - source clock (required) + "hclk" - HCLK which used for host (required) + "source_cg" - independent source clock gate (required for MT2712) +- pinctrl-names: should be "default", "state_uhs" +- pinctrl-0: should contain default/high speed pin ctrl +- pinctrl-1: should contain uhs mode pin ctrl +- vmmc-supply: power to the Core +- vqmmc-supply: power to the IO + +Optional properties: +- assigned-clocks: PLL of the source clock +- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock +- hs400-ds-delay: HS400 DS delay setting +- mediatek,hs200-cmd-int-delay: HS200 command internal delay setting. + This field has total 32 stages. + The value is an integer from 0 to 31. +- mediatek,hs400-cmd-int-delay: HS400 command internal delay setting + This field has total 32 stages. + The value is an integer from 0 to 31. +- mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection + If present,HS400 command responses are sampled on rising edges. + If not present,HS400 command responses are sampled on falling edges. +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc + error caused by stop clock(fifo full) + Valid range = [0:0x7]. if not present, default value is 0. + applied to compatible "mediatek,mt2701-mmc". + +Examples: +mmc0: mmc@11230000 { + compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc"; + reg = <0 0x11230000 0 0x108>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; + vmmc-supply = <&mt6397_vemc_3v3_reg>; + vqmmc-supply = <&mt6397_vio18_reg>; + clocks = <&pericfg CLK_PERI_MSDC30_0>, + <&topckgen CLK_TOP_MSDC50_0_H_SEL>; + clock-names = "source", "hclk"; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; + hs400-ds-delay = <0x14015>; + mediatek,hs200-cmd-int-delay = <26>; + mediatek,hs400-cmd-int-delay = <14>; + mediatek,hs400-cmd-resp-sel-rising; +}; |