diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pwm')
44 files changed, 1360 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt new file mode 100644 index 000000000..cfda0d57d --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for Atmel's HLCDC (High-end LCD Controller) PWM driver + +The Atmel HLCDC PWM is subdevice of the HLCDC MFD device. +See ../mfd/atmel-hlcdc.txt for more details. + +Required properties: + - compatible: value should be one of the following: + "atmel,hlcdc-pwm" + - pinctr-names: the pin control state names. Should contain "default". + - pinctrl-0: should contain the pinctrl states described by pinctrl + default. + - #pwm-cells: should be set to 3. This PWM chip use the default 3 cells + bindings defined in pwm.txt in this directory. + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt new file mode 100644 index 000000000..c8c831d7b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt @@ -0,0 +1,34 @@ +Atmel PWM controller + +Required properties: + - compatible: should be one of: + - "atmel,at91sam9rl-pwm" + - "atmel,sama5d3-pwm" + - "atmel,sama5d2-pwm" + - reg: physical base address and length of the controller's registers + - #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Example: + + pwm0: pwm@f8034000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xf8034000 0x400>; + #pwm-cells = <3>; + }; + + pwmleds { + compatible = "pwm-leds"; + + d1 { + label = "d1"; + pwms = <&pwm0 3 5000 0> + max-brightness = <255>; + }; + + d2 { + label = "d2"; + pwms = <&pwm0 1 5000 1> + max-brightness = <255>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt new file mode 100644 index 000000000..8031148bc --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt @@ -0,0 +1,16 @@ +Atmel TCB PWM controller + +Required properties: +- compatible: should be "atmel,tcb-pwm" +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. +- tc-block: The Timer Counter block to use as a PWM chip. + +Example: + +pwm { + compatible = "atmel,tcb-pwm"; + #pwm-cells = <3>; + tc-block = <1>; +}; diff --git a/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt new file mode 100644 index 000000000..d9254a6da --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt @@ -0,0 +1,20 @@ +Broadcom BCM7038 PWM controller (BCM7xxx Set Top Box PWM controller) + +Required properties: + +- compatible: must be "brcm,bcm7038-pwm" +- reg: physical base address and length for this controller +- #pwm-cells: should be 2. See pwm.txt in this directory for a description + of the cells format +- clocks: a phandle to the reference clock for this block which is fed through + its internal variable clock frequency generator + + +Example: + + pwm: pwm@f0408000 { + compatible = "brcm,bcm7038-pwm"; + reg = <0xf0408000 0x28>; + #pwm-cells = <2>; + clocks = <&upg_fixed>; + }; diff --git a/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt new file mode 100644 index 000000000..21f75bbd6 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt @@ -0,0 +1,21 @@ +Broadcom iProc PWM controller device tree bindings + +This controller has 4 channels. + +Required Properties : +- compatible: must be "brcm,iproc-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle + clock specifier pair for the external clock +- #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +pwm: pwm@18031000 { + compatible = "brcm,iproc-pwm"; + reg = <0x18031000 0x28>; + clocks = <&osc>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt new file mode 100644 index 000000000..8eae9fe78 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt @@ -0,0 +1,21 @@ +Broadcom Kona PWM controller device tree bindings + +This controller has 6 channels. + +Required Properties : +- compatible: should contain "brcm,kona-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle + clock specifier pair for the external clock +- #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +pwm: pwm@3e01a000 { + compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm"; + reg = <0x3e01a000 0xc4>; + clocks = <&pwm_clk>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt new file mode 100644 index 000000000..c0b202823 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt @@ -0,0 +1,15 @@ +* Cirris Logic CLPS711X PWM controller + +Required properties: +- compatible: Shall contain "cirrus,ep7209-pwm". +- reg: Physical base address and length of the controller's registers. +- clocks: phandle + clock specifier pair of the PWM reference clock. +- #pwm-cells: Should be 1. The cell specifies the index of the channel. + +Example: + pwm: pwm@80000400 { + compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm"; + reg = <0x80000400 0x4>; + clocks = <&clks 8>; + #pwm-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.txt b/Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.txt new file mode 100644 index 000000000..472bd46ab --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/google,cros-ec-pwm.txt @@ -0,0 +1,23 @@ +* PWM controlled by ChromeOS EC + +Google's ChromeOS EC PWM is a simple PWM attached to the Embedded Controller +(EC) and controlled via a host-command interface. + +An EC PWM node should be only found as a sub-node of the EC node (see +Documentation/devicetree/bindings/mfd/cros-ec.txt). + +Required properties: +- compatible: Must contain "google,cros-ec-pwm" +- #pwm-cells: Should be 1. The cell specifies the PWM index. + +Example: + cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + cros_ec_pwm: ec-pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/img-pwm.txt b/Documentation/devicetree/bindings/pwm/img-pwm.txt new file mode 100644 index 000000000..fade5f26f --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/img-pwm.txt @@ -0,0 +1,24 @@ +*Imagination Technologies PWM DAC driver + +Required properties: + - compatible: Should be "img,pistachio-pwm" + - reg: Should contain physical base address and length of pwm registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. + - clock-names: Must include the following entries. + - pwm: PWM operating clock. + - sys: PWM system interface clock. + - #pwm-cells: Should be 2. See pwm.txt in this directory for the + description of the cells format. + - img,cr-periph: Must contain a phandle to the peripheral control + syscon node which contains PWM control registers. + +Example: + pwm: pwm@18101300 { + compatible = "img,pistachio-pwm"; + reg = <0x18101300 0x100>; + clocks = <&pwm_clk>, <&system_clk>; + clock-names = "pwm", "sys"; + #pwm-cells = <2>; + img,cr-periph = <&cr_periph>; + }; diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt new file mode 100644 index 000000000..c61bdf8cd --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -0,0 +1,27 @@ +Freescale i.MX PWM controller + +Required properties: +- compatible : should be "fsl,<soc>-pwm" and one of the following + compatible strings: + - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1 + - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27 +- reg: physical base address and length of the controller's registers +- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.txt + in this directory for a description of the cells format. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt +- interrupts: The interrupt for the pwm controller + +Example: + +pwm1: pwm@53fb4000 { + #pwm-cells = <3>; + compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; + reg = <0x53fb4000 0x4000>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; + clock-names = "ipg", "per"; + interrupts = <61>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt new file mode 100644 index 000000000..7d9d3f906 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt @@ -0,0 +1,25 @@ +Ingenic JZ47xx PWM Controller +============================= + +Required properties: +- compatible: One of: + * "ingenic,jz4740-pwm" + * "ingenic,jz4770-pwm" + * "ingenic,jz4780-pwm" +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description + of the cells format. +- clocks : phandle to the external clock. +- clock-names : Should be "ext". + + +Example: + + pwm: pwm@10002000 { + compatible = "ingenic,jz4740-pwm"; + reg = <0x10002000 0x1000>; + + #pwm-cells = <3>; + + clocks = <&ext>; + clock-names = "ext"; + }; diff --git a/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt new file mode 100644 index 000000000..36e49d432 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt @@ -0,0 +1,20 @@ +* NXP LPC18xx State Configurable Timer - Pulse Width Modulator driver + +Required properties: + - compatible: Should be "nxp,lpc1850-sct-pwm" + - reg: Should contain physical base address and length of pwm registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. + - clock-names: Must include the following entries. + - pwm: PWM operating clock. + - #pwm-cells: Should be 3. See pwm.txt in this directory for the description + of the cells format. + +Example: + pwm: pwm@40000000 { + compatible = "nxp,lpc1850-sct-pwm"; + reg = <0x40000000 0x1000>; + clocks =<&ccu1 CLK_CPU_SCT>; + clock-names = "pwm"; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt new file mode 100644 index 000000000..74b5bc5dd --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt @@ -0,0 +1,17 @@ +LPC32XX PWM controller + +Required properties: +- compatible: should be "nxp,lpc3220-pwm" +- reg: physical base address and length of the controller's registers + +Examples: + +pwm@4005c000 { + compatible = "nxp,lpc3220-pwm"; + reg = <0x4005c000 0x4>; +}; + +pwm@4005c004 { + compatible = "nxp,lpc3220-pwm"; + reg = <0x4005c004 0x4>; +}; diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt new file mode 100644 index 000000000..96cdde5f6 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt @@ -0,0 +1,17 @@ +Freescale MXS PWM controller + +Required properties: +- compatible: should be "fsl,imx23-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- fsl,pwm-number: the number of PWM devices + +Example: + +pwm: pwm@80064000 { + compatible = "fsl,imx28-pwm", "fsl,imx23-pwm"; + reg = <0x80064000 0x2000>; + #pwm-cells = <2>; + fsl,pwm-number = <8>; +}; diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt new file mode 100644 index 000000000..c57e11b8d --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -0,0 +1,76 @@ +Tegra SoC PWFM controller + +Required properties: +- compatible: Must be: + - "nvidia,tegra20-pwm": for Tegra20 + - "nvidia,tegra30-pwm", "nvidia,tegra20-pwm": for Tegra30 + - "nvidia,tegra114-pwm", "nvidia,tegra20-pwm": for Tegra114 + - "nvidia,tegra124-pwm", "nvidia,tegra20-pwm": for Tegra124 + - "nvidia,tegra132-pwm", "nvidia,tegra20-pwm": for Tegra132 + - "nvidia,tegra210-pwm", "nvidia,tegra20-pwm": for Tegra210 + - "nvidia,tegra186-pwm": for Tegra186 +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pwm + +Optional properties: +============================ +In some of the interface like PWM based regulator device, it is required +to configure the pins differently in different states, especially in suspend +state of the system. The configuration of pin is provided via the pinctrl +DT node as detailed in the pinctrl DT binding document + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +The PWM node will have following optional properties. +pinctrl-names: Pin state names. Must be "default" and "sleep". +pinctrl-0: phandle for the default/active state of pin configurations. +pinctrl-1: phandle for the sleep state of pin configurations. + +Example: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + clocks = <&tegra_car 17>; + resets = <&tegra_car 17>; + reset-names = "pwm"; + }; + + +Example with the pin configuration for suspend and resume: +========================================================= +Suppose pin PE7 (On Tegra210) interfaced with the regulator device and +it requires PWM output to be tristated when system enters suspend. +Following will be DT binding to achieve this: + +#include <dt-bindings/pinctrl/pinctrl-tegra.h> + + pinmux@700008d4 { + pwm_active_state: pwm_active_state { + pe7 { + nvidia,pins = "pe7"; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + }; + }; + + pwm_sleep_state: pwm_sleep_state { + pe7 { + nvidia,pins = "pe7"; + nvidia,tristate = <TEGRA_PIN_ENABLE>; + }; + }; + }; + + pwm@7000a000 { + /* Mandatory PWM properties */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&pwm_active_state>; + pinctrl-1 = <&pwm_sleep_state>; + }; diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt new file mode 100644 index 000000000..f84ec9d29 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt @@ -0,0 +1,27 @@ +NXP PCA9685 16-channel 12-bit PWM LED controller +================================================ + +Required properties: + - compatible: "nxp,pca9685-pwm" + - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of + the cells format. + The index 16 is the ALLCALL channel, that sets all PWM channels at the same + time. + +Optional properties: + - invert (bool): boolean to enable inverted logic + - open-drain (bool): boolean to configure outputs with open-drain structure; + if omitted use totem-pole structure + +Example: + +For LEDs that are directly connected to the PCA, the following setting is +applicable: + +pca: pca@41 { + compatible = "nxp,pca9685-pwm"; + #pwm-cells = <2>; + reg = <0x41>; + invert; + open-drain; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt new file mode 100644 index 000000000..8cf87d1bf --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -0,0 +1,30 @@ +BCM2835 PWM controller (Raspberry Pi controller) + +Required properties: +- compatible: should be "brcm,bcm2835-pwm" +- reg: physical base address and length of the controller's registers +- clocks: This clock defines the base clock frequency of the PWM hardware + system, the period and the duty_cycle of the PWM signal is a multiple of + the base period. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Examples: + +pwm@2020c000 { + compatible = "brcm,bcm2835-pwm"; + reg = <0x2020c000 0x28>; + clocks = <&clk_pwm>; + #pwm-cells = <3>; +}; + +clocks { + .... + clk_pwm: pwm { + compatible = "fixed-clock"; + reg = <3>; + #clock-cells = <0>; + clock-frequency = <9200000>; + }; + .... +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-berlin.txt b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt new file mode 100644 index 000000000..82cbe16fc --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt @@ -0,0 +1,17 @@ +Berlin PWM controller + +Required properties: +- compatible: should be "marvell,berlin-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle to the input clock +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + +pwm: pwm@f7f20000 { + compatible = "marvell,berlin-pwm"; + reg = <0xf7f20000 0x40>; + clocks = <&chip_clk CLKID_CFG>; + #pwm-cells = <3>; +} diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt new file mode 100644 index 000000000..576ad002b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -0,0 +1,55 @@ +Freescale FlexTimer Module (FTM) PWM controller + +The same FTM PWM device can have a different endianness on different SoCs. The +device tree provides a property to describing this so that an operating system +device driver can handle all variants of the device. Refer to the table below +for the endianness of the FTM PWM block as integrated into the existing SoCs: + + SoC | FTM-PWM endianness + --------+------------------- + Vybrid | LE + LS1 | BE + LS2 | LE + +Please see ../regmap/regmap.txt for more detail about how to specify endian +modes in device tree. + + +Required properties: +- compatible : should be "fsl,<soc>-ftm-pwm" and one of the following + compatible strings: + - "fsl,vf610-ftm-pwm" for PWM compatible with the one integrated on VF610 + - "fsl,imx8qm-ftm-pwm" for PWM compatible with the one integrated on i.MX8QM +- reg: Physical base address and length of the controller's registers +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. +- clock-names: Should include the following module clock source entries: + "ftm_sys" (module clock, also can be used as counter clock), + "ftm_ext" (external counter clock), + "ftm_fix" (fixed counter clock), + "ftm_cnt_clk_en" (external and fixed counter clock enable/disable). +- clocks: Must contain a phandle and clock specifier for each entry in + clock-names, please see clock/clock-bindings.txt for details of the property + values. +- pinctrl-names: Must contain a "default" entry. +- pinctrl-NNN: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. +- big-endian: Boolean property, required if the FTM PWM registers use a big- + endian rather than little-endian layout. + +Example: + +pwm0: pwm@40038000 { + compatible = "fsl,vf610-ftm-pwm"; + reg = <0x40038000 0x1000>; + #pwm-cells = <3>; + clock-names = "ftm_sys", "ftm_ext", + "ftm_fix", "ftm_cnt_clk_en"; + clocks = <&clks VF610_CLK_FTM0>, + <&clks VF610_CLK_FTM0_EXT_SEL>, + <&clks VF610_CLK_FTM0_FIX_SEL>, + <&clks VF610_CLK_FTM0_EXT_FIX_EN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_1>; + big-endian; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt new file mode 100644 index 000000000..fa7849d67 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt @@ -0,0 +1,21 @@ +Hisilicon PWM controller + +Required properties: +-compatible: should contain one SoC specific compatible string + The SoC specific strings supported including: + "hisilicon,hi3516cv300-pwm" + "hisilicon,hi3519v100-pwm" +- reg: physical base address and length of the controller's registers. +- clocks: phandle and clock specifier of the PWM reference clock. +- resets: phandle and reset specifier for the PWM controller reset. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + pwm: pwm@12130000 { + compatible = "hisilicon,hi3516cv300-pwm"; + reg = <0x12130000 0x10000>; + clocks = <&crg_ctrl HI3516CV300_PWM_CLK>; + resets = <&crg_ctrl 0x38 0>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt new file mode 100644 index 000000000..7bd9d3b12 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt @@ -0,0 +1,58 @@ +TI/National Semiconductor LP3943 PWM controller + +Required properties: + - compatible: "ti,lp3943-pwm" + - #pwm-cells: Should be 2. See pwm.txt in this directory for a + description of the cells format. + Note that this hardware limits the period length to the + range 6250~1600000. + - ti,pwm0 or ti,pwm1: Output pin number(s) for PWM channel 0 or 1. + 0 = output 0 + 1 = output 1 + . + . + 15 = output 15 + +Example: +PWM 0 is for RGB LED brightness control +PWM 1 is for brightness control of LP8557 backlight device + +&i2c3 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + /* + * PWM 0 : output 8, 9 and 10 + * PWM 1 : output 15 + */ + pwm3943: pwm { + compatible = "ti,lp3943-pwm"; + #pwm-cells = <2>; + ti,pwm0 = <8 9 10>; + ti,pwm1 = <15>; + }; + }; + +}; + +/* LEDs control with PWM 0 of LP3943 */ +pwmleds { + compatible = "pwm-leds"; + rgb { + label = "indi::rgb"; + pwms = <&pwm3943 0 10000>; + max-brightness = <255>; + }; +}; + +&i2c4 { + /* Backlight control with PWM 1 of LP3943 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + pwms = <&pwm3943 1 10000>; + pwm-names = "lp8557"; + }; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt new file mode 100644 index 000000000..991728cb4 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt @@ -0,0 +1,40 @@ +MediaTek PWM controller + +Required properties: + - compatible: should be "mediatek,<name>-pwm": + - "mediatek,mt2712-pwm": found on mt2712 SoC. + - "mediatek,mt7622-pwm": found on mt7622 SoC. + - "mediatek,mt7623-pwm": found on mt7623 SoC. + - "mediatek,mt7628-pwm": found on mt7628 SoC. + - reg: physical base address and length of the controller's registers. + - #pwm-cells: must be 2. See pwm.txt in this directory for a description of + the cell format. + - clocks: phandle and clock specifier of the PWM reference clock. + - clock-names: must contain the following, except for MT7628 which + has no clocks + - "top": the top clock generator + - "main": clock used by the PWM core + - "pwm1-8": the eight per PWM clocks for mt2712 + - "pwm1-6": the six per PWM clocks for mt7622 + - "pwm1-5": the five per PWM clocks for mt7623 + - pinctrl-names: Must contain a "default" entry. + - pinctrl-0: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. + +Example: + pwm0: pwm@11006000 { + compatible = "mediatek,mt7623-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&topckgen CLK_TOP_PWM_SEL>, + <&pericfg CLK_PERI_PWM>, + <&pericfg CLK_PERI_PWM1>, + <&pericfg CLK_PERI_PWM2>, + <&pericfg CLK_PERI_PWM3>, + <&pericfg CLK_PERI_PWM4>, + <&pericfg CLK_PERI_PWM5>; + clock-names = "top", "main", "pwm1", "pwm2", + "pwm3", "pwm4", "pwm5"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-meson.txt b/Documentation/devicetree/bindings/pwm/pwm-meson.txt new file mode 100644 index 000000000..1fa3f7182 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-meson.txt @@ -0,0 +1,26 @@ +Amlogic Meson PWM Controller +============================ + +Required properties: +- compatible: Shall contain "amlogic,meson8b-pwm" + or "amlogic,meson-gxbb-pwm" + or "amlogic,meson-gxbb-ao-pwm" + or "amlogic,meson-axg-ee-pwm" + or "amlogic,meson-axg-ao-pwm" +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Optional properties: +- clocks: Could contain one or two parents clocks phandle for each of the two + PWM channels. +- clock-names: Could contain at least the "clkin0" and/or "clkin1" names. + +Example: + + pwm_ab: pwm@8550 { + compatible = "amlogic,meson-gxbb-pwm"; + reg = <0x0 0x08550 0x0 0x10>; + #pwm-cells = <3>; + clocks = <&xtal>, <&xtal>; + clock-names = "clkin0", "clkin1"; + } diff --git a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt new file mode 100644 index 000000000..6f8af2bcc --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt @@ -0,0 +1,43 @@ +MediaTek display PWM controller + +Required properties: + - compatible: should be "mediatek,<name>-disp-pwm": + - "mediatek,mt2701-disp-pwm": found on mt2701 SoC. + - "mediatek,mt6595-disp-pwm": found on mt6595 SoC. + - "mediatek,mt8173-disp-pwm": found on mt8173 SoC. + - reg: physical base address and length of the controller's registers. + - #pwm-cells: must be 2. See pwm.txt in this directory for a description of + the cell format. + - clocks: phandle and clock specifier of the PWM reference clock. + - clock-names: must contain the following: + - "main": clock used to generate PWM signals. + - "mm": sync signals from the modules of mmsys. + - pinctrl-names: Must contain a "default" entry. + - pinctrl-0: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. + +Example: + pwm0: pwm@1401e000 { + compatible = "mediatek,mt8173-disp-pwm", + "mediatek,mt6595-disp-pwm"; + reg = <0 0x1401e000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&mmsys CLK_MM_DISP_PWM026M>, + <&mmsys CLK_MM_DISP_PWM0MM>; + clock-names = "main", "mm"; + pinctrl-names = "default"; + pinctrl-0 = <&disp_pwm0_pins>; + }; + + backlight_lcd: backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm0 0 1000000>; + brightness-levels = < + 0 16 32 48 64 80 96 112 + 128 144 160 176 192 208 224 240 + 255 + >; + default-brightness-level = <9>; + power-supply = <&mt6397_vio18_reg>; + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt new file mode 100644 index 000000000..5ccfcc82d --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt @@ -0,0 +1,22 @@ +* OMAP PWM for dual-mode timers + +Required properties: +- compatible: Shall contain "ti,omap-dmtimer-pwm". +- ti,timers: phandle to PWM capable OMAP timer. See timer/ti,timer.txt for info + about these timers. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Optional properties: +- ti,prescaler: Should be a value between 0 and 7, see the timers datasheet +- ti,clock-source: Set dmtimer parent clock, values between 0 and 2: + - 0x00 - high-frequency system clock (timer_sys_ck) + - 0x01 - 32-kHz always-on clock (timer_32k_ck) + - 0x02 - external clock (timer_ext_ck, OMAP2 only) + +Example: + pwm9: dmtimer-pwm@9 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer9>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt new file mode 100644 index 000000000..2c5e52a5b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -0,0 +1,27 @@ +Rockchip PWM controller + +Required properties: + - compatible: should be "rockchip,<name>-pwm" + "rockchip,rk2928-pwm": found on RK29XX,RK3066 and RK3188 SoCs + "rockchip,rk3288-pwm": found on RK3288 SOC + "rockchip,rv1108-pwm", "rockchip,rk3288-pwm": found on RV1108 SoC + "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC + - reg: physical base address and length of the controller's registers + - clocks: See ../clock/clock-bindings.txt + - For older hardware (rk2928, rk3066, rk3188, rk3228, rk3288, rk3399): + - There is one clock that's used both to derive the functional clock + for the device and as the bus clock. + - For newer hardware (rk3328 and future socs): specified by name + - "pwm": This is used to derive the functional clock. + - "pclk": This is the APB bus clock. + - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory + for a description of the cell format. + +Example: + + pwm0: pwm@20030000 { + compatible = "rockchip,rk2928-pwm"; + reg = <0x20030000 0x10>; + clocks = <&cru PCLK_PWM01>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt new file mode 100644 index 000000000..5538de9c2 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt @@ -0,0 +1,51 @@ +* Samsung PWM timers + +Samsung SoCs contain PWM timer blocks which can be used for system clock source +and clock event timers, as well as to drive SoC outputs with PWM signal. Each +PWM timer block provides 5 PWM channels (not all of them can drive physical +outputs - see SoC and board manual). + +Be aware that the clocksource driver supports only uniprocessor systems. + +Required properties: +- compatible : should be one of following: + samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs + samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs + samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs + samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, + Exynos4210 rev0 SoCs + samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, + Exynos4x12, Exynos5250 and Exynos5420 SoCs +- reg: base address and size of register area +- interrupts: list of timer interrupts (one interrupt per timer, starting at + timer 0) +- clock-names: should contain all following required clock names: + - "timers" - PWM base clock used to generate PWM signals, + and any subset of following optional clock names: + - "pwm-tclk0" - first external PWM clock source, + - "pwm-tclk1" - second external PWM clock source. + Note that not all IP variants allow using all external clock sources. + Refer to SoC documentation to learn which clock source configurations + are available. +- clocks: should contain clock specifiers of all clocks, which input names + have been specified in clock-names property, in same order. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. + +Optional properties: +- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular + platform - an array of up to 5 elements being indices of PWM channels + (from 0 to 4), the order does not matter. + +Example: + pwm@7f006000 { + compatible = "samsung,s3c6400-pwm"; + reg = <0x7f006000 0x1000>; + interrupt-parent = <&vic0>; + interrupts = <23>, <24>, <25>, <27>, <28>; + clocks = <&clock 67>; + clock-names = "timers"; + samsung,pwm-outputs = <0>, <1>; + #pwm-cells = <3>; + } diff --git a/Documentation/devicetree/bindings/pwm/pwm-st.txt b/Documentation/devicetree/bindings/pwm/pwm-st.txt new file mode 100644 index 000000000..19fce774c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-st.txt @@ -0,0 +1,43 @@ +STMicroelectronics PWM driver bindings +-------------------------------------- + +Required parameters: +- compatible : "st,pwm" +- #pwm-cells : Number of cells used to specify a PWM. First cell + specifies the per-chip index of the PWM to use and the + second cell is the period in nanoseconds - fixed to 2 + for STiH41x. +- reg : Physical base address and length of the controller's + registers. +- pinctrl-names: Set to "default". +- pinctrl-0: List of phandles pointing to pin configuration nodes + for PWM module. + For Pinctrl properties, please refer to [1]. +- clock-names: Valid entries are "pwm" and/or "capture". +- clocks: phandle of the clock used by the PWM module. + For Clk properties, please refer to [2]. +- interrupts: IRQ for the Capture device + +Optional properties: +- st,pwm-num-chan: Number of available PWM channels. Default is 0. +- st,capture-num-chan: Number of available Capture channels. Default is 0. + +[1] Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Example: + +pwm1: pwm@fe510000 { + compatible = "st,pwm"; + reg = <0xfe510000 0x68>; + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1_chan0_default + &pinctrl_pwm1_chan1_default + &pinctrl_pwm1_chan2_default + &pinctrl_pwm1_chan3_default>; + clocks = <&clk_sysin>; + clock-names = "pwm"; + st,pwm-num-chan = <4>; + st,capture-num-chan = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt new file mode 100644 index 000000000..bd23302e8 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -0,0 +1,27 @@ +STMicroelectronics STM32 Low-Power Timer PWM + +STM32 Low-Power Timer provides single channel PWM. + +Must be a sub-node of an STM32 Low-Power Timer device tree node. +See ../mfd/stm32-lptimer.txt for details about the parent node. + +Required parameters: +- compatible: Must be "st,stm32-pwm-lp". +- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells + bindings defined in pwm.txt. + +Optional properties: +- pinctrl-names: Set to "default". +- pinctrl-0: Phandle pointing to pin configuration node for PWM. + +Example: + timer@40002400 { + compatible = "st,stm32-lptimer"; + ... + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&lppwm1_pins>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt new file mode 100644 index 000000000..3e6d55018 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt @@ -0,0 +1,35 @@ +STMicroelectronics STM32 Timers PWM bindings + +Must be a sub-node of an STM32 Timers device tree node. +See ../mfd/stm32-timers.txt for details about the parent node. + +Required parameters: +- compatible: Must be "st,stm32-pwm". +- pinctrl-names: Set to "default". +- pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module. + For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt + +Optional parameters: +- st,breakinput: One or two <index level filter> to describe break input configurations. + "index" indicates on which break input (0 or 1) the configuration + should be applied. + "level" gives the active level (0=low or 1=high) of the input signal + for this configuration. + "filter" gives the filtering value to be applied. + +Example: + timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 160>; + clock-names = "int"; + + pwm { + compatible = "st,stm32-pwm"; + pinctrl-0 = <&pwm1_pins>; + pinctrl-names = "default"; + st,breakinput = <0 1 5>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt new file mode 100644 index 000000000..2a1affbff --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt @@ -0,0 +1,24 @@ +Allwinner sun4i and sun7i SoC PWM controller + +Required properties: + - compatible: should be one of: + - "allwinner,sun4i-a10-pwm" + - "allwinner,sun5i-a10s-pwm" + - "allwinner,sun5i-a13-pwm" + - "allwinner,sun7i-a20-pwm" + - "allwinner,sun8i-h3-pwm" + - "allwinner,sun50i-a64-pwm", "allwinner,sun5i-a13-pwm" + - "allwinner,sun50i-h5-pwm", "allwinner,sun5i-a13-pwm" + - reg: physical base address and length of the controller's registers + - #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. + - clocks: From common clock binding, handle to the parent clock. + +Example: + + pwm: pwm@1c20e00 { + compatible = "allwinner,sun7i-a20-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 000000000..06a363d9c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,50 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,<soc>-ecap". + for am33xx - compatible = "ti,am3352-ecap", "ti,am33xx-ecap"; + for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + for da850 - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap"; + for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap"; +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The PWM channel index ranges from 0 to 4. The only third + cell flag supported by this binding is PWM_POLARITY_INVERTED. +- reg: physical base address and size of the registers map. + +Optional properties: +- clocks: Handle to the ECAP's functional clock. +- clock-names: Must be set to "fck". + +Example: + +ecap0: ecap@48300100 { /* ECAP on am33xx */ + compatible = "ti,am3352-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "fck"; +}; + +ecap0: ecap@48300100 { /* ECAP on am4372 */ + compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; + clocks = <&l4ls_gclk>; + clock-names = "fck"; +}; + +ecap0: ecap@1f06000 { /* ECAP on da850 */ + compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x1f06000 0x80>; +}; + +ecap0: ecap@4843e100 { + compatible = "ti,dra746-ecap", "ti,am3352-ecap"; + #pwm-cells = <3>; + reg = <0x4843e100 0x80>; + clocks = <&l4_root_clk_div>; + clock-names = "fck"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 000000000..944fe356b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,49 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible: Must be "ti,<soc>-ehrpwm". + for am33xx - compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + for am4372 - compatible = "ti,am4372-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm"; + for da850 - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm"; + for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm"; +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. +- reg: physical base address and size of the registers map. + +Optional properties: +- clocks: Handle to the PWM's time-base and functional clock. +- clock-names: Must be set to "tbclk" and "fck". + +Example: + +ehrpwm0: pwm@48300200 { /* EHRPWM on am33xx */ + compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>; + clock-names = "tbclk", "fck"; +}; + +ehrpwm0: pwm@48300200 { /* EHRPWM on am4372 */ + compatible = "ti,am4372-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x80>; + clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>; + clock-names = "tbclk", "fck"; + ti,hwmods = "ehrpwm0"; +}; + +ehrpwm0: pwm@1f00000 { /* EHRPWM on da850 */ + compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x1f00000 0x2000>; +}; + +ehrpwm0: pwm@4843e200 { /* EHRPWM on dra746 */ + compatible = "ti,dra746-ehrpwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x4843e200 0x80>; + clocks = <&ehrpwm0_tbclk>, <&l4_root_clk_div>; + clock-names = "tbclk", "fck"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 000000000..4633697fb --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,58 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,<soc>-pwmss". + for am33xx - compatible = "ti,am33xx-pwmss"; + for am4372 - compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + for dra746 - compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss" + +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +epwmss0: epwmss@48300000 { /* PWMSS for am33xx */ + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; + +epwmss0: epwmss@48300000 { /* PWMSS for am4372 */ + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss" + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; + +epwmss0: epwmss@4843e000 { /* PWMSS for DRA7xx */ + compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss"; + reg = <0x4843e000 0x30>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-zx.txt b/Documentation/devicetree/bindings/pwm/pwm-zx.txt new file mode 100644 index 000000000..a6bcc75c9 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-zx.txt @@ -0,0 +1,22 @@ +ZTE ZX PWM controller + +Required properties: + - compatible: Should be "zte,zx296718-pwm". + - reg: Physical base address and length of the controller's registers. + - clocks : The phandle and specifier referencing the controller's clocks. + - clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller. The + PCLK is for register access, while WCLK is the reference clock for + calculating period and duty cycles. + - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + + pwm: pwm@1439000 { + compatible = "zte,zx296718-pwm"; + reg = <0x1439000 0x1000>; + clocks = <&lsp1crm LSP1_PWM_PCLK>, + <&lsp1crm LSP1_PWM_WCLK>; + clock-names = "pclk", "wclk"; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt new file mode 100644 index 000000000..8556263b8 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -0,0 +1,69 @@ +Specifying PWM information for devices +====================================== + +1) PWM user nodes +----------------- + +PWM users should specify a list of PWM devices that they want to use +with a property containing a 'pwm-list': + + pwm-list ::= <single-pwm> [pwm-list] + single-pwm ::= <pwm-phandle> <pwm-specifier> + pwm-phandle : phandle to PWM controller node + pwm-specifier : array of #pwm-cells specifying the given PWM + (controller specific) + +PWM properties should be named "pwms". The exact meaning of each pwms +property must be documented in the device tree binding for each device. +An optional property "pwm-names" may contain a list of strings to label +each of the PWM devices listed in the "pwms" property. If no "pwm-names" +property is given, the name of the user node will be used as fallback. + +Drivers for devices that use more than a single PWM device can use the +"pwm-names" property to map the name of the PWM device requested by the +pwm_get() call to an index into the list given by the "pwms" property. + +The following example could be used to describe a PWM-based backlight +device: + + pwm: pwm { + #pwm-cells = <2>; + }; + + [...] + + bl: backlight { + pwms = <&pwm 0 5000000>; + pwm-names = "backlight"; + }; + +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + +pwm-specifier typically encodes the chip-relative PWM number and the PWM +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags (defined in +<dt-bindings/pwm/pwm.h>) in a third cell: +- PWM_POLARITY_INVERTED: invert the PWM signal polarity + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>; + pwm-names = "backlight"; + }; + +2) PWM controller nodes +----------------------- + +PWM controller nodes must specify the number of cells used for the +specifier using the '#pwm-cells' property. + +An example PWM controller might look like this: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pxa-pwm.txt b/Documentation/devicetree/bindings/pwm/pxa-pwm.txt new file mode 100644 index 000000000..5ae9f1e3c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pxa-pwm.txt @@ -0,0 +1,30 @@ +Marvell PWM controller + +Required properties: +- compatible: should be one or more of: + - "marvell,pxa250-pwm" + - "marvell,pxa270-pwm" + - "marvell,pxa168-pwm" + - "marvell,pxa910-pwm" +- reg: Physical base address and length of the registers used by the PWM channel + Note that one device instance must be created for each PWM that is used, so the + length covers only the register window for one PWM output, not that of the + entire PWM controller. Currently length is 0x10 for all supported devices. +- #pwm-cells: Should be 1. This cell is used to specify the period in + nanoseconds. + +Example PWM device node: + +pwm0: pwm@40b00000 { + compatible = "marvell,pxa250-pwm"; + reg = <0x40b00000 0x10>; + #pwm-cells = <1>; +}; + +Example PWM client node: + +backlight { + compatible = "pwm-backlight"; + pwms = <&pwm0 5000000>; + ... +} diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt new file mode 100644 index 000000000..e1ef6afbe --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -0,0 +1,35 @@ +* Renesas R-Car PWM Timer Controller + +Required Properties: +- compatible: should be "renesas,pwm-rcar" and one of the following. + - "renesas,pwm-r8a7743": for RZ/G1M + - "renesas,pwm-r8a7745": for RZ/G1E + - "renesas,pwm-r8a7778": for R-Car M1A + - "renesas,pwm-r8a7779": for R-Car H1 + - "renesas,pwm-r8a7790": for R-Car H2 + - "renesas,pwm-r8a7791": for R-Car M2-W + - "renesas,pwm-r8a7794": for R-Car E2 + - "renesas,pwm-r8a7795": for R-Car H3 + - "renesas,pwm-r8a7796": for R-Car M3-W + - "renesas,pwm-r8a77965": for R-Car M3-N + - "renesas,pwm-r8a77990": for R-Car E3 + - "renesas,pwm-r8a77995": for R-Car D3 +- reg: base address and length of the registers block for the PWM. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- clocks: clock phandle and specifier pair. +- pinctrl-0: phandle, referring to a default pin configuration node. +- pinctrl-names: Set to "default". + +Example: R8A7743 (RZ/G1M) PWM Timer node + + pwm0: pwm@e6e30000 { + compatible = "renesas,pwm-r8a7743", "renesas,pwm-rcar"; + reg = <0 0xe6e30000 0 0x8>; + clocks = <&cpg CPG_MOD 523>; + power-domains = <&sysc R8A7743_PD_ALWAYS_ON>; + resets = <&cpg 523>; + #pwm-cells = <2>; + pinctrl-0 = <&pwm0_pins>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt new file mode 100644 index 000000000..d53a16715 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -0,0 +1,29 @@ +* Renesas R-Car Timer Pulse Unit PWM Controller + +Required Properties: + + - compatible: should be one of the following. + - "renesas,tpu-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible PWM controller. + - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. + - "renesas,tpu-r8a7743": for R8A7743 (RZ/G1M) compatible PWM controller. + - "renesas,tpu-r8a7745": for R8A7745 (RZ/G1E) compatible PWM controller. + - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. + - "renesas,tpu": for generic R-Car and RZ/G1 TPU PWM controller. + + - reg: Base address and length of each memory resource used by the PWM + controller hardware module. + + - #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. + +Please refer to pwm.txt in this directory for details of the common PWM bindings +used by client devices. + +Example: R8A7740 (R-Mobile A1) TPU controller node + + tpu: pwm@e6600000 { + compatible = "renesas,tpu-r8a7740", "renesas,tpu"; + reg = <0xe6600000 0x148>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 000000000..b486de2c3 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,17 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt new file mode 100644 index 000000000..cb209646b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt @@ -0,0 +1,18 @@ +== ST STMPE PWM controller == + +This is a PWM block embedded in the ST Microelectronics STMPE +(ST Multi-Purpose Expander) chips. The PWM is registered as a +subdevices of the STMPE MFD device. + +Required properties: +- compatible: should be: + - "st,stmpe-pwm" +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + +pwm0: pwm { + compatible = "st,stmpe-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 000000000..4e32bee11 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 000000000..9f4b46090 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 000000000..a76390e6d --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,18 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <3>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; |