diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/qcom,dwc3.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/qcom,dwc3.txt | 103 |
1 files changed, 103 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt new file mode 100644 index 000000000..95afdcf3c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -0,0 +1,103 @@ +Qualcomm SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Compatible list, contains + "qcom,dwc3" + "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,sdm845-dwc3" for sdm845 SOC. +- reg: Offset and length of register set for QSCRATCH wrapper +- power-domains: specifies a phandle to PM domain provider node +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "core" Master/Core clock, have to be >= 125 MHz for SS + operation and >= 60MHz for HS operation + "mock_utmi" Mock utmi clock needed for ITP/SOF generation in + host mode. Its frequency should be 19.2MHz. + "sleep" Sleep clock, used for wakeup when USB3 core goes + into low power mode (U3). + +Optional clocks: + "iface" System bus AXI clock. + Not present on "qcom,msm8996-dwc3" compatible. + "cfg_noc" System Config NOC clock. + Not present on "qcom,msm8996-dwc3" compatible. +- assigned-clocks: Should be: + MOCK_UTMI_CLK + MASTER_CLK +- assigned-clock-rates: Should be: + 19.2Mhz (192000000) for MOCK_UTMI_CLK + >=125Mhz (125000000) for MASTER_CLK in SS mode + >=60Mhz (60000000) for MASTER_CLK in HS mode + +Optional properties: +- resets: Phandle to reset control that resets core and wrapper. +- interrupts: specifies interrupts from controller wrapper used + to wakeup from low power/susepnd state. Must contain + one or more entry for interrupt-names property +- interrupt-names: Must include the following entries: + - "hs_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB2 bus + - "ss_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB3 bus + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate + interrupts for any wakeup event on DM and DP lines +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. + Used when dwc3 operates without SSPHY and only + HS/FS/LS modes are supported. + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY + +Example device nodes: + + hs_phy: phy@100f8800 { + compatible = "qcom,qusb2-v2-phy"; + ... + }; + + ss_phy: phy@100f8830 { + compatible = "qcom,qmp-v3-usb3-phy"; + ... + }; + + usb3_0: usb30@a6f8800 { + compatible = "qcom,dwc3"; + reg = <0xa6f8800 0x400>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "core", "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <133000000>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; + + dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <0 205 0x4>; + phys = <&hs_phy>, <&ss_phy>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + }; + }; + |