diff options
Diffstat (limited to 'drivers/usb/dwc3/core.c')
| -rw-r--r-- | drivers/usb/dwc3/core.c | 57 |
1 files changed, 40 insertions, 17 deletions
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index 81a5ca15b..c6de1dcf2 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -242,11 +242,48 @@ static int dwc3_core_soft_reset(struct dwc3 *dwc) /* * We're resetting only the device side because, if we're in host mode, * XHCI driver will reset the host block. If dwc3 was configured for - * host-only mode, then we can return early. + * host-only mode or current role is host, then we can return early. */ if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST) return 0; + /* + * If the dr_mode is host and the dwc->current_dr_role is not the + * corresponding DWC3_GCTL_PRTCAP_HOST, then the dwc3_core_init_mode + * isn't executed yet. Ensure the phy is ready before the controller + * updates the GCTL.PRTCAPDIR or other settings by soft-resetting + * the phy. + * + * Note: GUSB3PIPECTL[n] and GUSB2PHYCFG[n] are port settings where n + * is port index. If this is a multiport host, then we need to reset + * all active ports. + */ + if (dwc->dr_mode == USB_DR_MODE_HOST) { + u32 usb3_port; + u32 usb2_port; + + usb3_port = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0)); + usb3_port |= DWC3_GUSB3PIPECTL_PHYSOFTRST; + dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), usb3_port); + + usb2_port = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); + usb2_port |= DWC3_GUSB2PHYCFG_PHYSOFTRST; + dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), usb2_port); + + /* Small delay for phy reset assertion */ + usleep_range(1000, 2000); + + usb3_port &= ~DWC3_GUSB3PIPECTL_PHYSOFTRST; + dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), usb3_port); + + usb2_port &= ~DWC3_GUSB2PHYCFG_PHYSOFTRST; + dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), usb2_port); + + /* Wait for clock synchronization */ + msleep(50); + return 0; + } + reg = dwc3_readl(dwc->regs, DWC3_DCTL); reg |= DWC3_DCTL_CSFTRST; dwc3_writel(dwc->regs, DWC3_DCTL, reg); @@ -993,22 +1030,6 @@ static int dwc3_core_init(struct dwc3 *dwc) dwc3_writel(dwc->regs, DWC3_GUCTL1, reg); } - if (dwc->dr_mode == USB_DR_MODE_HOST || - dwc->dr_mode == USB_DR_MODE_OTG) { - reg = dwc3_readl(dwc->regs, DWC3_GUCTL); - - /* - * Enable Auto retry Feature to make the controller operating in - * Host mode on seeing transaction errors(CRC errors or internal - * overrun scenerios) on IN transfers to reply to the device - * with a non-terminating retry ACK (i.e, an ACK transcation - * packet with Retry=1 & Nump != 0) - */ - reg |= DWC3_GUCTL_HSTINAUTORETRY; - - dwc3_writel(dwc->regs, DWC3_GUCTL, reg); - } - /* * Must config both number of packets and max burst settings to enable * RX and/or TX threshold. @@ -1509,6 +1530,8 @@ static int dwc3_probe(struct platform_device *pdev) pm_runtime_put(dev); + dma_set_max_seg_size(dev, UINT_MAX); + return 0; err5: |