Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 73 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
new file mode 100644
index 000000000..17c1d2bd0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -0,0 +1,73 @@
+PHY nodes
+
+Required properties:
+
+ - interrupts : interrupt specifier for the sole interrupt.
+ - reg : The ID number for the phy, usually a small integer
+
+Optional Properties:
+
+- compatible: Compatible list, may contain
+  "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for
+  PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45
+  specifications. If neither of these are specified, the default is to
+  assume clause 22.
+
+  If the PHY reports an incorrect ID (or none at all) then the
+  "compatible" list may contain an entry with the correct PHY ID in the
+  form: "ethernet-phy-idAAAA.BBBB" where
+     AAAA - The value of the 16 bit Phy Identifier 1 register as
+            4 hex digits. This is the chip vendor OUI bits 3:18
+     BBBB - The value of the 16 bit Phy Identifier 2 register as
+            4 hex digits. This is the chip vendor OUI bits 19:24,
+            followed by 10 bits of a vendor specific ID.
+
+  The compatible list should not contain other values than those
+  listed here.
+
+- max-speed: Maximum PHY supported speed (10, 100, 1000...)
+
+- broken-turn-around: If set, indicates the PHY device does not correctly
+  release the turn around line low at the end of a MDIO transaction.
+
+- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to
+  compensate for the board being designed with the lanes swapped.
+
+- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the
+  TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong
+  bootstrap configuration caused by issues in PCB layout design.
+
+- eee-broken-100tx:
+- eee-broken-1000t:
+- eee-broken-10gt:
+- eee-broken-1000kx:
+- eee-broken-10gkx4:
+- eee-broken-10gkr:
+  Mark the corresponding energy efficient ethernet mode as broken and
+  request the ethernet to stop advertising it.
+
+- phy-is-integrated: If set, indicates that the PHY is integrated into the same
+  physical package as the Ethernet MAC. If needed, muxers should be configured
+  to ensure the integrated PHY is used. The absence of this property indicates
+  the muxers should be configured so that the external PHY is used.
+
+- reset-gpios: The GPIO phandle and specifier for the PHY reset signal.
+
+- reset-assert-us: Delay after the reset was asserted in microseconds.
+  If this property is missing the delay will be skipped.
+
+- reset-deassert-us: Delay after the reset was deasserted in microseconds.
+  If this property is missing the delay will be skipped.
+
+Example:
+
+ethernet-phy@0 {
+	compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22";
+	interrupt-parent = <&PIC>;
+	interrupts = <35 IRQ_TYPE_EDGE_RISING>;
+	reg = <0>;
+
+	reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	reset-assert-us = <1000>;
+	reset-deassert-us = <2000>;
+};