Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

54 files changed, 1313 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/watchdog/alphascale-asm9260.txt b/Documentation/devicetree/bindings/watchdog/alphascale-asm9260.txt
new file mode 100644
index 000000000..75b265a04
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/alphascale-asm9260.txt
@@ -0,0 +1,35 @@
+Alphascale asm9260 Watchdog timer
+
+Required properties:
+
+- compatible : should be "alphascale,asm9260-wdt".
+- reg : Specifies base physical address and size of the registers.
+- clocks : the clocks feeding the watchdog timer. See clock-bindings.txt
+- clock-names : should be set to
+	"mod" - source for tick counter.
+	"ahb" - ahb gate.
+- resets : phandle pointing to the system reset controller with
+	line index for the watchdog.
+- reset-names : should be set to "wdt_rst".
+
+Optional properties:
+- timeout-sec : shall contain the default watchdog timeout in seconds,
+	if unset, the default timeout is 30 seconds.
+- alphascale,mode : three modes are supported
+	"hw" - hw reset (default).
+	"sw" - sw reset.
+	"debug" - no action is taken.
+
+Example:
+
+watchdog0: watchdog@80048000 {
+	compatible = "alphascale,asm9260-wdt";
+	reg = <0x80048000 0x10>;
+	clocks = <&acc CLKID_SYS_WDT>, <&acc CLKID_AHB_WDT>;
+	clock-names = "mod", "ahb";
+	interrupts = <55>;
+	resets = <&rst WDT_RESET>;
+	reset-names = "wdt_rst";
+	timeout-sec = <30>;
+	alphascale,mode = "hw";
+};
diff --git a/Documentation/devicetree/bindings/watchdog/arm,sp805.txt b/Documentation/devicetree/bindings/watchdog/arm,sp805.txt
new file mode 100644
index 000000000..bee6f1f0e
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/arm,sp805.txt
@@ -0,0 +1,32 @@
+ARM AMBA Primecell SP805 Watchdog
+
+SP805 WDT is a ARM Primecell Peripheral and has a standard-id register that
+can be used to identify the peripheral type, vendor, and revision.
+This value can be used for driver matching.
+
+As SP805 WDT is a primecell IP, it follows the base bindings specified in
+'arm/primecell.txt'
+
+Required properties:
+- compatible:  Should be "arm,sp805" & "arm,primecell"
+- reg:         Should contain location and length for watchdog timer register
+- clocks:      Clocks driving the watchdog timer hardware. This list should be
+               2 clocks. With 2 clocks, the order is wdog_clk, apb_pclk
+               wdog_clk can be equal to or be a sub-multiple of the apb_pclk
+               frequency
+- clock-names: Shall be "wdog_clk" for first clock and "apb_pclk" for the
+               second one
+
+Optional properties:
+- interrupts:  Should specify WDT interrupt number
+- timeout-sec: Should specify default WDT timeout in seconds. If unset, the
+               default timeout is determined by the driver
+
+Example:
+	watchdog@66090000 {
+		compatible = "arm,sp805", "arm,primecell";
+		reg = <0x66090000 0x1000>;
+		interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&wdt_clk>, <&apb_pclk>;
+		clock-names = "wdog_clk", "apb_pclk";
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt
new file mode 100644
index 000000000..c5077a1f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt
@@ -0,0 +1,56 @@
+Aspeed Watchdog Timer
+
+Required properties:
+ - compatible: must be one of:
+	- "aspeed,ast2400-wdt"
+	- "aspeed,ast2500-wdt"
+
+ - reg: physical base address of the controller and length of memory mapped
+   region
+
+Optional properties:
+
+ - aspeed,reset-type = "cpu|soc|system|none"
+
+   Reset behavior - Whenever a timeout occurs the watchdog can be programmed
+   to generate one of three different, mutually exclusive, types of resets.
+
+   Type "none" can be specified to indicate that no resets are to be done.
+   This is useful in situations where another watchdog engine on chip is
+   to perform the reset.
+
+   If 'aspeed,reset-type=' is not specfied the default is to enable system
+   reset.
+
+   Reset types:
+
+        - cpu: Reset CPU on watchdog timeout
+
+        - soc: Reset 'System on Chip' on watchdog timeout
+
+        - system: Reset system on watchdog timeout
+
+        - none: No reset is performed on timeout. Assumes another watchdog
+                engine is responsible for this.
+
+ - aspeed,alt-boot:    If property is present then boot from alternate block.
+ - aspeed,external-signal: If property is present then signal is sent to
+			external reset counter (only WDT1 and WDT2). If not
+			specified no external signal is sent.
+ - aspeed,ext-pulse-duration: External signal pulse duration in microseconds
+
+Optional properties for AST2500-compatible watchdogs:
+ - aspeed,ext-push-pull: If aspeed,external-signal is present, set the pin's
+			 drive type to push-pull. The default is open-drain.
+ - aspeed,ext-active-high: If aspeed,external-signal is present and and the pin
+			   is configured as push-pull, then set the pulse
+			   polarity to active-high. The default is active-low.
+
+Example:
+
+	wdt1: watchdog@1e785000 {
+		compatible = "aspeed,ast2400-wdt";
+		reg = <0x1e785000 0x1c>;
+		aspeed,reset-type = "system";
+		aspeed,external-signal;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-at91rm9200-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-at91rm9200-wdt.txt
new file mode 100644
index 000000000..d4d86cf8f
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/atmel-at91rm9200-wdt.txt
@@ -0,0 +1,9 @@
+Atmel AT91RM9200 System Timer Watchdog
+
+Required properties:
+- compatible: must be "atmel,at91sam9260-wdt".
+
+Example:
+	watchdog@fffffd00 {
+		compatible = "atmel,at91rm9200-wdt";
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
new file mode 100644
index 000000000..4fec1e372
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
@@ -0,0 +1,34 @@
+* Atmel SAMA5D4 Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible: "atmel,sama5d4-wdt"
+- reg: base physical address and length of memory mapped region.
+
+Optional properties:
+- timeout-sec: watchdog timeout value (in seconds).
+- interrupts: interrupt number to the CPU.
+- atmel,watchdog-type: should be "hardware" or "software".
+	"hardware": enable watchdog fault reset. A watchdog fault triggers
+		    watchdog reset.
+	"software": enable watchdog fault interrupt. A watchdog fault asserts
+		    watchdog interrupt.
+- atmel,idle-halt: present if you want to stop the watchdog when the CPU is
+		   in idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
+- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is
+		  in debug state.
+
+Example:
+	watchdog@fc068640 {
+		compatible = "atmel,sama5d4-wdt";
+		reg = <0xfc068640 0x10>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH 5>;
+		timeout-sec = <10>;
+		atmel,watchdog-type = "hardware";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
new file mode 100644
index 000000000..711a880b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
@@ -0,0 +1,51 @@
+* Atmel Watchdog Timers
+
+** at91sam9-wdt
+
+Required properties:
+- compatible: must be "atmel,at91sam9260-wdt".
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- clocks: phandle to input clock.
+
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+- interrupts : Should contain WDT interrupt.
+- atmel,max-heartbeat-sec : Should contain the maximum heartbeat value in
+	seconds. This value should be less or equal to 16. It is used to
+	compute the WDV field.
+- atmel,min-heartbeat-sec : Should contain the minimum heartbeat value in
+	seconds. This value must be smaller than the max-heartbeat-sec value.
+	It is used to compute the WDD field.
+- atmel,watchdog-type : Should be "hardware" or "software". Hardware watchdog
+	use the at91 watchdog reset. Software watchdog use the watchdog
+	interrupt to trigger a software reset.
+- atmel,reset-type : Should be "proc" or "all".
+	"all" : assert peripherals and processor reset signals
+	"proc" : assert the processor reset signal
+	This is valid only when using "hardware" watchdog.
+- atmel,disable : Should be present if you want to disable the watchdog.
+- atmel,idle-halt : Should be present if you want to stop the watchdog when
+	entering idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
+- atmel,dbg-halt : Should be present if you want to stop the watchdog when
+	entering debug state.
+
+Example:
+	watchdog@fffffd40 {
+		compatible = "atmel,at91sam9260-wdt";
+		reg = <0xfffffd40 0x10>;
+		interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+		clocks = <&clk32k>;
+		timeout-sec = <15>;
+		atmel,watchdog-type = "hardware";
+		atmel,reset-type = "all";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+		atmel,max-heartbeat-sec = <16>;
+		atmel,min-heartbeat-sec = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt
new file mode 100644
index 000000000..f801d71de
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt
@@ -0,0 +1,18 @@
+BCM2835 Watchdog timer
+
+Required properties:
+
+- compatible : should be "brcm,bcm2835-pm-wdt"
+- reg : Specifies base physical address and size of the registers.
+
+Optional properties:
+
+- timeout-sec   : Contains the watchdog timeout in seconds
+
+Example:
+
+watchdog {
+	compatible = "brcm,bcm2835-pm-wdt";
+	reg = <0x7e100000 0x28>;
+	timeout-sec = <10>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt
new file mode 100644
index 000000000..84122270b
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt
@@ -0,0 +1,19 @@
+BCM7038 Watchdog timer
+
+Required properties:
+
+- compatible : should be "brcm,bcm7038-wdt"
+- reg : Specifies base physical address and size of the registers.
+
+Optional properties:
+
+- clocks: The clock running the watchdog. If no clock is found the
+	  driver will default to 27000000 Hz.
+
+Example:
+
+watchdog@f040a7e8 {
+	compatible = "brcm,bcm7038-wdt";
+	clocks = <&upg_fixed>;
+	reg = <0xf040a7e8 0x16>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/brcm,kona-wdt.txt b/Documentation/devicetree/bindings/watchdog/brcm,kona-wdt.txt
new file mode 100644
index 000000000..2b86a00e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/brcm,kona-wdt.txt
@@ -0,0 +1,15 @@
+Broadcom Kona Family Watchdog Timer
+-----------------------------------
+
+This watchdog timer is used in the following Broadcom SoCs:
+  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+Required properties:
+  - compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt";
+  - reg: memory address & range
+
+Example:
+	watchdog@35002f40 {
+		compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt";
+		reg = <0x35002f40 0x6c>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt
new file mode 100644
index 000000000..750a87657
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt
@@ -0,0 +1,23 @@
+Zynq Watchdog Device Tree Bindings
+-------------------------------------------
+
+Required properties:
+- compatible		: Should be "cdns,wdt-r1p2".
+- clocks		: This is pclk (APB clock).
+- interrupts		: This is wd_irq - watchdog timeout interrupt.
+
+Optional properties
+- reset-on-timeout	: If this property exists, then a reset is done
+			  when watchdog times out.
+- timeout-sec		: Watchdog timeout value (in seconds).
+
+Example:
+	watchdog@f8005000 {
+		compatible = "cdns,wdt-r1p2";
+		clocks = <&clkc 45>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 9 1>;
+		reg = <0xf8005000 0x1000>;
+		reset-on-timeout;
+		timeout-sec = <10>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
new file mode 100644
index 000000000..b935b526d
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/da9062-wdt.txt
@@ -0,0 +1,23 @@
+* Dialog Semiconductor DA9062/61 Watchdog Timer
+
+Required properties:
+
+- compatible: should be one of the following valid compatible string lines:
+	"dlg,da9061-watchdog", "dlg,da9062-watchdog"
+	"dlg,da9062-watchdog"
+
+Example: DA9062
+
+	pmic0: da9062@58 {
+		watchdog {
+			compatible = "dlg,da9062-watchdog";
+		};
+	};
+
+Example: DA9061 using a fall-back compatible for the DA9062 watchdog driver
+
+	pmic0: da9061@58 {
+		watchdog {
+			compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
+		};
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt
new file mode 100644
index 000000000..e60b9a13b
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt
@@ -0,0 +1,24 @@
+Texas Instruments DaVinci/Keystone Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible : Should be "ti,davinci-wdt", "ti,keystone-wdt"
+- reg : Should contain WDT registers location and length
+
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+- clocks : the clock feeding the watchdog timer.
+	   Needed if platform uses clocks.
+	   See clock-bindings.txt
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/spruer5b/spruer5b.pdf
+Keystone - http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf
+
+Examples:
+
+wdt: wdt@2320000 {
+	compatible = "ti,davinci-wdt";
+	reg = <0x02320000 0x80>;
+	timeout-sec = <30>;
+	clocks = <&clkwdtimer0>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/digicolor-wdt.txt b/Documentation/devicetree/bindings/watchdog/digicolor-wdt.txt
new file mode 100644
index 000000000..a882967e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/digicolor-wdt.txt
@@ -0,0 +1,25 @@
+Conexant Digicolor SoCs Watchdog timer
+
+The watchdog functionality in Conexant Digicolor SoCs relies on the so called
+"Agent Communication" block. This block includes the eight programmable system
+timer counters. The first timer (called "Timer A") is the only one that can be
+used as watchdog.
+
+Required properties:
+
+- compatible : Should be "cnxt,cx92755-wdt"
+- reg : Specifies base physical address and size of the registers
+- clocks : phandle; specifies the clock that drives the timer
+
+Optional properties:
+
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Example:
+
+	watchdog@f0000fc0 {
+		compatible = "cnxt,cx92755-wdt";
+		reg = <0xf0000fc0 0x8>;
+		clocks = <&main_clk>;
+		timeout-sec = <15>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/dw_wdt.txt b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt
new file mode 100644
index 000000000..eb0914420
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/dw_wdt.txt
@@ -0,0 +1,24 @@
+Synopsys Designware Watchdog Timer
+
+Required Properties:
+
+- compatible	: Should contain "snps,dw-wdt"
+- reg		: Base address and size of the watchdog timer registers.
+- clocks	: phandle + clock-specifier for the clock that drives the
+		watchdog timer.
+
+Optional Properties:
+
+- interrupts	: The interrupt used for the watchdog timeout warning.
+- resets	: phandle pointing to the system reset controller with
+		line index for the watchdog.
+
+Example:
+
+	watchdog0: wd@ffd02000 {
+		compatible = "snps,dw-wdt";
+		reg = <0xffd02000 0x1000>;
+		interrupts = <0 171 4>;
+		clocks = <&per_base_clk>;
+		resets = <&rst WDT0_RESET>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt
new file mode 100644
index 000000000..9ecdb502e
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt
@@ -0,0 +1,22 @@
+Faraday Technology FTWDT010 watchdog
+
+This is an IP part from Faraday Technology found in the Gemini
+SoCs and others.
+
+Required properties:
+- compatible : must be one of
+  "faraday,ftwdt010"
+  "cortina,gemini-watchdog", "faraday,ftwdt010"
+- reg : shall contain base register location and length
+- interrupts : shall contain the interrupt for the watchdog
+
+Optional properties:
+- timeout-sec : the default watchdog timeout in seconds.
+
+Example:
+
+watchdog@41000000 {
+	compatible = "faraday,ftwdt010";
+	reg = <0x41000000 0x1000>;
+	interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt
new file mode 100644
index 000000000..adc6b76fc
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt
@@ -0,0 +1,24 @@
+* Freescale i.MX Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible : Should be "fsl,<soc>-wdt"
+- reg : Should contain WDT registers location and length
+- interrupts : Should contain WDT interrupt
+
+Optional properties:
+- big-endian: If present the watchdog device's registers are implemented
+  in big endian mode, otherwise in native mode(same with CPU), for more
+  detail please see: Documentation/devicetree/bindings/regmap/regmap.txt.
+- fsl,ext-reset-output: If present the watchdog device is configured to
+  assert its external reset (WDOG_B) instead of issuing a software reset.
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Examples:
+
+wdt@73f98000 {
+	compatible = "fsl,imx51-wdt", "fsl,imx21-wdt";
+	reg = <0x73f98000 0x4000>;
+	interrupts = <58>;
+	big-endian;
+	timeout-sec = <20>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
new file mode 100644
index 000000000..198794963
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
@@ -0,0 +1,28 @@
+* GPIO-controlled Watchdog
+
+Required Properties:
+- compatible: Should contain "linux,wdt-gpio".
+- gpios: From common gpio binding; gpio connection to WDT reset pin.
+- hw_algo: The algorithm used by the driver. Should be one of the
+  following values:
+  - toggle: Either a high-to-low or a low-to-high transition clears
+    the WDT counter. The watchdog timer is disabled when GPIO is
+    left floating or connected to a three-state buffer.
+  - level: Low or high level starts counting WDT timeout,
+    the opposite level disables the WDT. Active level is determined
+    by the GPIO flags.
+- hw_margin_ms: Maximum time to reset watchdog circuit (milliseconds).
+
+Optional Properties:
+- always-running: If the watchdog timer cannot be disabled, add this flag to
+  have the driver keep toggling the signal without a client. It will only cease
+  to toggle the signal when the device is open and the timeout elapsed.
+
+Example:
+	watchdog: watchdog {
+		/* ADM706 */
+		compatible = "linux,wdt-gpio";
+		gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+		hw_algo = "toggle";
+		hw_margin_ms = <1600>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt b/Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt
new file mode 100644
index 000000000..b2fa11fd4
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt
@@ -0,0 +1,19 @@
+*ImgTec PowerDown Controller (PDC) Watchdog Timer (WDT)
+
+Required properties:
+- compatible : Should be "img,pdc-wdt"
+- reg : Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdt" and "sys"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts : Should contain WDT interrupt
+
+Examples:
+
+watchdog@18102100 {
+	compatible = "img,pdc-wdt";
+	reg = <0x18102100 0x100>;
+	clocks = <&pdc_wdt_clk>, <&sys_clk>;
+	clock-names = "wdt", "sys";
+	interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
new file mode 100644
index 000000000..ce1cb72d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
@@ -0,0 +1,17 @@
+Ingenic Watchdog Timer (WDT) Controller for JZ4740 & JZ4780
+
+Required properties:
+compatible: "ingenic,jz4740-watchdog" or "ingenic,jz4780-watchdog"
+reg: Register address and length for watchdog registers
+clocks: phandle to the RTC clock
+clock-names: should be "rtc"
+
+Example:
+
+watchdog: jz4740-watchdog@10002000 {
+	compatible = "ingenic,jz4740-watchdog";
+	reg = <0x10002000 0x10>;
+
+	clocks = <&cgu JZ4740_CLK_RTC>;
+	clock-names = "rtc";
+};
diff --git a/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt b/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt
new file mode 100644
index 000000000..18d4d8302
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt
@@ -0,0 +1,24 @@
+Lantiq WTD watchdog binding
+============================
+
+This describes the binding of the Lantiq watchdog driver.
+
+-------------------------------------------------------------------------------
+Required properties:
+- compatible		: Should be one of
+				"lantiq,wdt"
+				"lantiq,xrx100-wdt"
+				"lantiq,xrx200-wdt", "lantiq,xrx100-wdt"
+				"lantiq,falcon-wdt"
+- reg			: Address of the watchdog block
+- lantiq,rcu		: A phandle to the RCU syscon (required for
+			  "lantiq,falcon-wdt" and "lantiq,xrx100-wdt")
+
+-------------------------------------------------------------------------------
+Example for the watchdog on the xRX200 SoCs:
+		watchdog@803f0 {
+			compatible = "lantiq,xrx200-wdt", "lantiq,xrx100-wdt";
+			reg = <0x803f0 0x10>;
+
+			lantiq,rcu = <&rcu0>;
+		};
diff --git a/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt b/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt
new file mode 100644
index 000000000..09f6b2496
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt
@@ -0,0 +1,19 @@
+* NXP LPC18xx Watchdog Timer (WDT)
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-wwdt"
+- reg: Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdtclk" and "reg"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts: Should contain WDT interrupt
+
+Examples:
+
+watchdog@40080000 {
+	compatible = "nxp,lpc1850-wwdt";
+	reg = <0x40080000 0x24>;
+	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
+	clock-names = "wdtclk", "reg";
+	interrupts = <49>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/marvel.txt b/Documentation/devicetree/bindings/watchdog/marvel.txt
new file mode 100644
index 000000000..c1b67a78f
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/marvel.txt
@@ -0,0 +1,45 @@
+* Marvell Orion Watchdog Time
+
+Required Properties:
+
+- Compatibility : "marvell,orion-wdt"
+		  "marvell,armada-370-wdt"
+		  "marvell,armada-xp-wdt"
+		  "marvell,armada-375-wdt"
+		  "marvell,armada-380-wdt"
+
+- reg		: Should contain two entries: first one with the
+		  timer control address, second one with the
+		  rstout enable address.
+
+For "marvell,armada-375-wdt" and "marvell,armada-380-wdt":
+
+- reg		: A third entry is mandatory and should contain the
+                  shared mask/unmask RSTOUT address.
+
+Clocks required for compatibles = "marvell,orion-wdt",
+				  "marvell,armada-370-wdt":
+- clocks : Must contain a single entry describing the clock input
+
+Clocks required for compatibles = "marvell,armada-xp-wdt"
+				  "marvell,armada-375-wdt"
+				  "marvell,armada-380-wdt":
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "nbclk" (L2/coherency fabric clock),
+  "fixed" (Reference 25 MHz fixed-clock).
+
+Optional properties:
+
+- interrupts	: Contains the IRQ for watchdog expiration
+- timeout-sec	: Contains the watchdog timeout in seconds
+
+Example:
+
+	wdt@20300 {
+		compatible = "marvell,orion-wdt";
+		reg = <0x20300 0x28>, <0x20108 0x4>;
+		interrupts = <3>;
+		timeout-sec = <10>;
+		clocks = <&gate_clk 7>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt b/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt
new file mode 100644
index 000000000..370dee322
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/men-a021-wdt.txt
@@ -0,0 +1,25 @@
+Bindings for MEN A21 Watchdog device connected to GPIO lines
+
+Required properties:
+- compatible: "men,a021-wdt"
+- gpios: Specifies the pins that control the Watchdog, order:
+  1: Watchdog enable
+  2: Watchdog fast-mode
+  3: Watchdog trigger
+  4: Watchdog reset cause bit 0
+  5: Watchdog reset cause bit 1
+  6: Watchdog reset cause bit 2
+
+Optional properties:
+- None
+
+Example:
+	watchdog {
+		compatible ="men,a021-wdt";
+		gpios = <&gpio3 9  1	/* WD_EN */
+			 &gpio3 10 1	/* WD_FAST */
+			 &gpio3 11 1	/* WD_TRIG */
+			 &gpio3 6  1	/* RST_CAUSE[0] */
+			 &gpio3 7  1	/* RST_CAUSE[1] */
+			 &gpio3 8  1>;	/* RST_CAUSE[2] */
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt
new file mode 100644
index 000000000..c7fe36fa7
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt
@@ -0,0 +1,16 @@
+Meson GXBB SoCs Watchdog timer
+
+Required properties:
+
+- compatible : should be "amlogic,meson-gxbb-wdt"
+- reg : Specifies base physical address and size of the registers.
+- clocks : Should be a phandle to the Watchdog clock source, for GXBB the xtal
+	   is the default clock source.
+
+Example:
+
+wdt: watchdog@98d0 {
+	compatible = "amlogic,meson-gxbb-wdt";
+	reg = <0 0x98d0 0x0 0x10>;
+	clocks = <&xtal>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
new file mode 100644
index 000000000..7588cc397
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
@@ -0,0 +1,21 @@
+Meson SoCs Watchdog timer
+
+Required properties:
+
+- compatible : depending on the SoC this should be one of:
+	"amlogic,meson6-wdt" on Meson6 SoCs
+	"amlogic,meson8-wdt" and "amlogic,meson6-wdt" on Meson8 SoCs
+	"amlogic,meson8b-wdt" on Meson8b SoCs
+	"amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs
+- reg : Specifies base physical address and size of the registers.
+
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+
+Example:
+
+wdt: watchdog@c1109900 {
+	compatible = "amlogic,meson6-wdt";
+	reg = <0xc1109900 0x8>;
+	timeout-sec = <10>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt
new file mode 100644
index 000000000..49485f831
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt
@@ -0,0 +1,19 @@
+* Microchip PIC32 Deadman Timer
+
+The deadman timer is used to reset the processor in the event of a software
+malfunction. It is a free-running instruction fetch timer, which is clocked
+whenever an instruction fetch occurs until a count match occurs.
+
+Required properties:
+- compatible: must be "microchip,pic32mzda-dmt".
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- clocks: phandle of source clk. Should be <&rootclk PB7CLK>.
+
+Example:
+
+	watchdog@1f800a00 {
+		compatible = "microchip,pic32mzda-dmt";
+		reg = <0x1f800a00 0x80>;
+		clocks = <&rootclk PB7CLK>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt
new file mode 100644
index 000000000..f03a29a1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt
@@ -0,0 +1,18 @@
+* Microchip PIC32 Watchdog Timer
+
+When enabled, the watchdog peripheral can be used to reset the device if the
+WDT is not cleared periodically in software.
+
+Required properties:
+- compatible: must be "microchip,pic32mzda-wdt".
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- clocks: phandle of source clk. Should be <&rootclk LPRCCLK>.
+
+Example:
+
+	watchdog@1f800800 {
+		compatible = "microchip,pic32mzda-wdt";
+		reg = <0x1f800800 0x200>;
+		clocks = <&rootclk LPRCCLK>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt b/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt
new file mode 100644
index 000000000..1169857d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/moxa,moxart-watchdog.txt
@@ -0,0 +1,15 @@
+MOXA ART Watchdog timer
+
+Required properties:
+
+- compatible : Must be "moxa,moxart-watchdog"
+- reg : Should contain registers location and length
+- clocks : Should contain phandle for the clock that drives the counter
+
+Example:
+
+	watchdog: watchdog@98500000 {
+		compatible = "moxa,moxart-watchdog";
+		reg = <0x98500000 0x10>;
+		clocks = <&coreclk>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/mt7621-wdt.txt b/Documentation/devicetree/bindings/watchdog/mt7621-wdt.txt
new file mode 100644
index 000000000..c15ef0ef6
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/mt7621-wdt.txt
@@ -0,0 +1,12 @@
+Ralink Watchdog Timers
+
+Required properties:
+- compatible: must be "mediatek,mt7621-wdt"
+- reg: physical base address of the controller and length of the register range
+
+Example:
+
+	watchdog@100 {
+		compatible = "mediatek,mt7621-wdt";
+		reg = <0x100 0x10>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
new file mode 100644
index 000000000..859dee167
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
@@ -0,0 +1,23 @@
+Mediatek SoCs Watchdog timer
+
+Required properties:
+
+- compatible should contain:
+	"mediatek,mt2701-wdt", "mediatek,mt6589-wdt": for MT2701
+	"mediatek,mt6589-wdt": for MT6589
+	"mediatek,mt6797-wdt", "mediatek,mt6589-wdt": for MT6797
+	"mediatek,mt7622-wdt", "mediatek,mt6589-wdt": for MT7622
+	"mediatek,mt7623-wdt", "mediatek,mt6589-wdt": for MT7623
+
+- reg : Specifies base physical address and size of the registers.
+
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+
+Example:
+
+wdt: watchdog@10000000 {
+	compatible = "mediatek,mt6589-wdt";
+	reg = <0x10000000 0x18>;
+	timeout-sec = <10>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt
new file mode 100644
index 000000000..6d593003c
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt
@@ -0,0 +1,28 @@
+Nuvoton NPCM Watchdog
+
+Nuvoton NPCM timer module provides five 24-bit timer counters, and a watchdog.
+The watchdog supports a pre-timeout interrupt that fires 10ms before the
+expiry.
+
+Required properties:
+- compatible      : "nuvoton,npcm750-wdt" for NPCM750 (Poleg).
+- reg             : Offset and length of the register set for the device.
+- interrupts      : Contain the timer interrupt with flags for
+                    falling edge.
+
+Required clocking property, have to be one of:
+- clocks          : phandle of timer reference clock.
+- clock-frequency : The frequency in Hz of the clock that drives the NPCM7xx
+                    timer (usually 25000000).
+
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Example:
+
+timer@f000801c {
+    compatible = "nuvoton,npcm750-wdt";
+    interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+    reg = <0xf000801c 0x4>;
+    clocks = <&clk NPCM7XX_CLK_TIMER>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt b/Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt
new file mode 100644
index 000000000..c6ae9c9d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt
@@ -0,0 +1,26 @@
+Xilinx AXI/PLB soft-core watchdog Device Tree Bindings
+---------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,xps-timebase-wdt-1.00.a" or
+			  "xlnx,xps-timebase-wdt-1.01.a".
+- reg			: Physical base address and size
+
+Optional properties:
+- clocks		: Input clock specifier. Refer to common clock
+			  bindings.
+- clock-frequency	: Frequency of clock in Hz
+- xlnx,wdt-enable-once	: 0 - Watchdog can be restarted
+			  1 - Watchdog can be enabled just once
+- xlnx,wdt-interval	: Watchdog timeout interval in 2^<val> clock cycles,
+			  <val> is integer from 8 to 31.
+
+Example:
+axi-timebase-wdt@40100000 {
+	clock-frequency = <50000000>;
+	compatible = "xlnx,xps-timebase-wdt-1.00.a";
+	clocks = <&clkc 15>;
+	reg = <0x40100000 0x10000>;
+	xlnx,wdt-enable-once = <0x0>;
+	xlnx,wdt-interval = <0x1b>;
+} ;
diff --git a/Documentation/devicetree/bindings/watchdog/omap-wdt.txt b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt
new file mode 100644
index 000000000..1fa20e453
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt
@@ -0,0 +1,15 @@
+TI Watchdog Timer (WDT) Controller for OMAP
+
+Required properties:
+- compatible : "ti,omap3-wdt" for OMAP3 or "ti,omap4-wdt" for OMAP4
+- ti,hwmods : Name of the hwmod associated to the WDT
+
+Optional properties:
+- timeout-sec : default watchdog timeout in seconds
+
+Examples:
+
+wdt2: wdt@4a314000 {
+	compatible = "ti,omap4-wdt", "ti,omap3-wdt";
+	ti,hwmods = "wd_timer2";
+};
diff --git a/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt b/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt
new file mode 100644
index 000000000..4b76bec62
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/pnx4008-wdt.txt
@@ -0,0 +1,17 @@
+* NXP PNX watchdog timer
+
+Required properties:
+- compatible: must be "nxp,pnx4008-wdt"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+
+Example:
+
+	watchdog@4003c000 {
+		compatible = "nxp,pnx4008-wdt";
+		reg = <0x4003C000 0x1000>;
+		timeout-sec = <10>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/qca-ar7130-wdt.txt b/Documentation/devicetree/bindings/watchdog/qca-ar7130-wdt.txt
new file mode 100644
index 000000000..7a89e5f85
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/qca-ar7130-wdt.txt
@@ -0,0 +1,13 @@
+* Qualcomm Atheros AR7130 Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible: must be "qca,ar7130-wdt"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+Example:
+
+wdt@18060008 {
+	compatible = "qca,ar9330-wdt", "qca,ar7130-wdt";
+	reg = <0x18060008 0x8>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt
new file mode 100644
index 000000000..41aeaa2ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt
@@ -0,0 +1,28 @@
+Qualcomm Krait Processor Sub-system (KPSS) Watchdog
+---------------------------------------------------
+
+Required properties :
+- compatible : shall contain only one of the following:
+
+			"qcom,kpss-wdt-msm8960"
+			"qcom,kpss-wdt-apq8064"
+			"qcom,kpss-wdt-ipq8064"
+			"qcom,kpss-wdt-ipq4019"
+			"qcom,kpss-timer"
+			"qcom,scss-timer"
+			"qcom,kpss-wdt"
+
+- reg : shall contain base register location and length
+- clocks : shall contain the input clock
+
+Optional properties :
+- timeout-sec : shall contain the default watchdog timeout in seconds,
+                if unset, the default timeout is 30 seconds
+
+Example:
+	watchdog@208a038 {
+		compatible = "qcom,kpss-wdt-ipq8064";
+		reg = <0x0208a038 0x40>;
+		clocks = <&sleep_clk>;
+		timeout-sec = <10>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt b/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt
new file mode 100644
index 000000000..05653054b
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt
@@ -0,0 +1,17 @@
+Realtek RTD1295 Watchdog
+========================
+
+Required properties:
+
+- compatible :  Should be "realtek,rtd1295-watchdog"
+- reg        :  Specifies the physical base address and size of registers
+- clocks     :  Specifies one clock input
+
+
+Example:
+
+	watchdog@98007680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x98007680 0x100>;
+		clocks = <&osc27M>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt
new file mode 100644
index 000000000..9407212a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt
@@ -0,0 +1,44 @@
+Renesas Watchdog Timer (WDT) Controller
+
+Required properties:
+ - compatible : Must be "renesas,<soctype>-wdt", followed by a generic
+		fallback compatible string when compatible with the generic
+		version.
+	       Examples with soctypes are:
+		 - "renesas,r8a7743-wdt" (RZ/G1M)
+		 - "renesas,r8a7745-wdt" (RZ/G1E)
+		 - "renesas,r8a774a1-wdt" (RZ/G2M)
+	         - "renesas,r8a7790-wdt" (R-Car H2)
+	         - "renesas,r8a7791-wdt" (R-Car M2-W)
+	         - "renesas,r8a7792-wdt" (R-Car V2H)
+	         - "renesas,r8a7793-wdt" (R-Car M2-N)
+	         - "renesas,r8a7794-wdt" (R-Car E2)
+	         - "renesas,r8a7795-wdt" (R-Car H3)
+	         - "renesas,r8a7796-wdt" (R-Car M3-W)
+		 - "renesas,r8a77965-wdt" (R-Car M3-N)
+	         - "renesas,r8a77970-wdt" (R-Car V3M)
+	         - "renesas,r8a77990-wdt" (R-Car E3)
+	         - "renesas,r8a77995-wdt" (R-Car D3)
+	         - "renesas,r7s72100-wdt" (RZ/A1)
+		The generic compatible string must be:
+		 - "renesas,rza-wdt" for RZ/A
+		 - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G1
+		 - "renesas,rcar-gen3-wdt" for R-Car Gen3 and RZ/G2
+
+- reg : Should contain WDT registers location and length
+- clocks : the clock feeding the watchdog timer.
+
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+- power-domains : the power domain the WDT belongs to
+- interrupts: Some WDTs have an interrupt when used in interval timer mode
+
+Examples:
+
+	wdt0: watchdog@e6020000 {
+		compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt";
+		reg = <0 0xe6020000 0 0x0c>;
+		clocks = <&cpg CPG_MOD 402>;
+		power-domains = <&cpg>;
+		timeout-sec = <60>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt b/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt
new file mode 100644
index 000000000..05b95bfa2
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/rt2880-wdt.txt
@@ -0,0 +1,18 @@
+Ralink Watchdog Timers
+
+Required properties:
+- compatible: must be "ralink,rt2880-wdt"
+- reg: physical base address of the controller and length of the register range
+
+Optional properties:
+- interrupts: Specify the INTC interrupt number
+
+Example:
+
+	watchdog@120 {
+		compatible = "ralink,rt2880-wdt";
+		reg = <0x120 0x10>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
new file mode 100644
index 000000000..46dcb48e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
@@ -0,0 +1,35 @@
+* Samsung's Watchdog Timer Controller
+
+The Samsung's Watchdog controller is used for resuming system operation
+after a preset amount of time during which the WDT reset event has not
+occurred.
+
+Required properties:
+- compatible : should be one among the following
+	- "samsung,s3c2410-wdt" for S3C2410
+	- "samsung,s3c6410-wdt" for S3C6410, S5PV210 and Exynos4
+	- "samsung,exynos5250-wdt" for Exynos5250
+	- "samsung,exynos5420-wdt" for Exynos5420
+	- "samsung,exynos7-wdt" for Exynos7
+
+- reg : base physical address of the controller and length of memory mapped
+	region.
+- interrupts : interrupt number to the cpu.
+- samsung,syscon-phandle : reference to syscon node (This property required only
+	in case of compatible being "samsung,exynos5250-wdt" or "samsung,exynos5420-wdt".
+	In case of Exynos5250 and 5420 this property points to syscon node holding the PMU
+	base address)
+
+Optional properties:
+- timeout-sec : contains the watchdog timeout in seconds.
+
+Example:
+
+watchdog@101d0000 {
+	compatible = "samsung,exynos5250-wdt";
+	reg = <0x101D0000 0x100>;
+	interrupts = <0 42 0>;
+	clocks = <&clock 336>;
+	clock-names = "watchdog";
+	samsung,syscon-phandle = <&pmu_syscon>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt
new file mode 100644
index 000000000..6f2d5f919
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt
@@ -0,0 +1,31 @@
+* SBSA (Server Base System Architecture) Generic Watchdog
+
+The SBSA Generic Watchdog Timer is used to force a reset of the system
+after two stages of timeout have elapsed.  A detailed definition of the
+watchdog timer can be found in the ARM document: ARM-DEN-0029 - Server
+Base System Architecture (SBSA)
+
+Required properties:
+- compatible: Should at least contain "arm,sbsa-gwdt".
+
+- reg: Each entry specifies the base physical address of a register frame
+  and the length of that frame; currently, two frames must be defined,
+  in this order:
+  1: Watchdog control frame;
+  2: Refresh frame.
+
+- interrupts: Should contain the Watchdog Signal 0 (WS0) SPI (Shared
+  Peripheral Interrupt) number of SBSA Generic Watchdog.
+
+Optional properties
+- timeout-sec: Watchdog timeout values (in seconds).
+
+Example for FVP Foundation Model v8:
+
+watchdog@2a440000 {
+	compatible = "arm,sbsa-gwdt";
+	reg = <0x0 0x2a440000 0 0x1000>,
+	      <0x0 0x2a450000 0 0x1000>;
+	interrupts = <0 27 4>;
+	timeout-sec = <30>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/sigma,smp8642-wdt.txt b/Documentation/devicetree/bindings/watchdog/sigma,smp8642-wdt.txt
new file mode 100644
index 000000000..5b7ec2c70
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/sigma,smp8642-wdt.txt
@@ -0,0 +1,18 @@
+Sigma Designs SMP86xx/SMP87xx watchdog
+
+Required properties:
+- compatible: Should be "sigma,smp8642-wdt"
+- reg: Specifies the physical address region
+- clocks: Should be a phandle to the clock
+
+Optional properties:
+- timeout-sec: watchdog timeout in seconds
+
+Example:
+
+watchdog@1fd00 {
+	compatible = "sigma,smp8642-wdt";
+	reg = <0x1fd00 8>;
+	clocks = <&xtal_in_clk>;
+	timeout-sec = <30>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt
new file mode 100644
index 000000000..0dce5e310
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt
@@ -0,0 +1,18 @@
+SiRFSoC Timer and Watchdog Timer(WDT) Controller
+
+Required properties:
+- compatible: "sirf,prima2-tick"
+- reg: Address range of tick timer/WDT register set
+- interrupts: interrupt number to the cpu
+
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Example:
+
+timer@b0020000 {
+	compatible = "sirf,prima2-tick";
+	reg = <0xb0020000 0x1000>;
+	interrupts = <0>;
+	timeout-sec = <30>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt b/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt
new file mode 100644
index 000000000..aeaf3e0ca
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt
@@ -0,0 +1,19 @@
+Spreadtrum SoCs Watchdog timer
+
+Required properties:
+- compatible : Should be "sprd,sp9860-wdt".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : Exactly one interrupt specifier.
+- timeout-sec : Contain the default watchdog timeout in seconds.
+- clock-names : Contain the input clock names.
+- clocks : Phandles to input clocks.
+
+Example:
+	watchdog: watchdog@40310000 {
+		compatible = "sprd,sp9860-wdt";
+		reg = <0 0x40310000 0 0x1000>;
+		interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+		timeout-sec = <12>;
+		clock-names = "enable", "rtc_enable";
+		clocks = <&clk_aon_apb_gates1 8>, <&clk_aon_apb_rtc_gates 9>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/st,stm32-iwdg.txt b/Documentation/devicetree/bindings/watchdog/st,stm32-iwdg.txt
new file mode 100644
index 000000000..d8f4430b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/st,stm32-iwdg.txt
@@ -0,0 +1,26 @@
+STM32 Independent WatchDoG (IWDG)
+---------------------------------
+
+Required properties:
+- compatible: Should be either:
+  - "st,stm32-iwdg"
+  - "st,stm32mp1-iwdg"
+- reg: Physical base address and length of the registers set for the device
+- clocks: Reference to the clock entry lsi. Additional pclk clock entry
+  is required only for st,stm32mp1-iwdg.
+- clock-names: Name of the clocks used.
+  "lsi" for st,stm32-iwdg
+  "lsi", "pclk" for st,stm32mp1-iwdg
+
+Optional Properties:
+- timeout-sec: Watchdog timeout value in seconds.
+
+Example:
+
+iwdg: watchdog@40003000 {
+	compatible = "st,stm32-iwdg";
+	reg = <0x40003000 0x400>;
+	clocks = <&clk_lsi>;
+	clock-names = "lsi";
+	timeout-sec = <32>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt b/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt
new file mode 100644
index 000000000..b949039bc
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt
@@ -0,0 +1,41 @@
+STMicroelectronics Low Power Controller (LPC) - Watchdog
+========================================================
+
+LPC currently supports Watchdog OR Real Time Clock OR Clocksource
+functionality.
+
+[See: ../rtc/rtc-st-lpc.txt for RTC options]
+[See: ../timer/st,stih407-lpc for Clocksource options]
+
+Required properties
+
+- compatible 	: Should be: "st,stih407-lpc"
+- reg		: LPC registers base address + size
+- interrupts    : LPC interrupt line number and associated flags
+- clocks	: Clock used by LPC device (See: ../clock/clock-bindings.txt)
+- st,lpc-mode	: The LPC can run either one of three modes:
+                  ST_LPC_MODE_RTC    [0]
+                  ST_LPC_MODE_WDT    [1]
+                  ST_LPC_MODE_CLKSRC [2]
+		 One (and only one) mode must be selected.
+
+Required properties [watchdog mode]
+
+- st,syscfg	: Phandle to syscfg node used to enable watchdog and configure
+		  CPU reset type.
+- timeout-sec	: Watchdog timeout in seconds
+
+Optional properties [watchdog mode]
+
+- st,warm-reset	: If present reset type will be 'warm' - if not it will be cold
+
+Example:
+	lpc@fde05000 {
+		compatible	= "st,stih407-lpc";
+		reg		= <0xfde05000 0x1000>;
+		clocks 		= <&clk_s_d3_flexgen CLK_LPC_0>;
+		st,syscfg	= <&syscfg_core>;
+		timeout-sec	= <120>;
+		st,lpc-mode	= <ST_LPC_MODE_WDT>;
+		st,warm-reset;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/stericsson-coh901327.txt b/Documentation/devicetree/bindings/watchdog/stericsson-coh901327.txt
new file mode 100644
index 000000000..8ffb88e39
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/stericsson-coh901327.txt
@@ -0,0 +1,19 @@
+ST-Ericsson COH 901 327 Watchdog timer
+
+Required properties:
+- compatible: must be "stericsson,coh901327".
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: the interrupt used for the watchdog timeout warning.
+
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+
+Example:
+
+watchdog: watchdog@c0012000 {
+	compatible = "stericsson,coh901327";
+	reg = <0xc0012000 0x1000>;
+	interrupts = <3>;
+	timeout-sec = <60>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt
new file mode 100644
index 000000000..ed11ce0ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt
@@ -0,0 +1,20 @@
+Allwinner SoCs Watchdog timer
+
+Required properties:
+
+- compatible : should be one of
+	"allwinner,sun4i-a10-wdt"
+	"allwinner,sun6i-a31-wdt"
+	"allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt"
+- reg : Specifies base physical address and size of the registers.
+
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Example:
+
+wdt: watchdog@1c20c90 {
+	compatible = "allwinner,sun4i-a10-wdt";
+	reg = <0x01c20c90 0x10>;
+	timeout-sec = <10>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt b/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt
new file mode 100644
index 000000000..8f6caad42
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/ts4800-wdt.txt
@@ -0,0 +1,25 @@
+Technologic Systems Watchdog
+
+Required properties:
+- compatible: must be "technologic,ts4800-wdt"
+- syscon: phandle / integer array that points to the syscon node which
+          describes the FPGA's syscon registers.
+          - phandle to FPGA's syscon
+          - offset to the watchdog register
+
+Optional property:
+- timeout-sec: contains the watchdog timeout in seconds.
+
+Example:
+
+syscon: syscon@b0010000 {
+	compatible = "syscon", "simple-mfd";
+	reg = <0xb0010000 0x3d>;
+	reg-io-width = <2>;
+
+	wdt@e {
+		compatible = "technologic,ts4800-wdt";
+		syscon = <&syscon 0xe>;
+		timeout-sec = <10>;
+	};
+}
diff --git a/Documentation/devicetree/bindings/watchdog/twl4030-wdt.txt b/Documentation/devicetree/bindings/watchdog/twl4030-wdt.txt
new file mode 100644
index 000000000..80a37193c
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/twl4030-wdt.txt
@@ -0,0 +1,10 @@
+Device tree bindings for twl4030-wdt driver (TWL4030 watchdog)
+
+Required properties:
+	compatible = "ti,twl4030-wdt";
+
+Example:
+
+watchdog {
+	compatible = "ti,twl4030-wdt";
+};
diff --git a/Documentation/devicetree/bindings/watchdog/uniphier-wdt.txt b/Documentation/devicetree/bindings/watchdog/uniphier-wdt.txt
new file mode 100644
index 000000000..bf6337546
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/uniphier-wdt.txt
@@ -0,0 +1,20 @@
+UniPhier watchdog timer controller
+
+This UniPhier watchdog timer controller must be under sysctrl node.
+
+Required properties:
+- compatible: should be "socionext,uniphier-wdt"
+
+Example:
+
+	sysctrl@61840000 {
+		compatible = "socionext,uniphier-ld11-sysctrl",
+			     "simple-mfd", "syscon";
+		reg = <0x61840000 0x4000>;
+
+		watchdog {
+			compatible = "socionext,uniphier-wdt";
+		}
+
+		other nodes ...
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/zii,rave-sp-wdt.txt b/Documentation/devicetree/bindings/watchdog/zii,rave-sp-wdt.txt
new file mode 100644
index 000000000..3de96186e
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/zii,rave-sp-wdt.txt
@@ -0,0 +1,39 @@
+Zodiac Inflight Innovations RAVE Supervisory Processor Watchdog Bindings
+
+RAVE SP watchdog device is a "MFD cell" device corresponding to
+watchdog functionality of RAVE Supervisory Processor. It is expected
+that its Device Tree node is specified as a child of the node
+corresponding to the parent RAVE SP device (as documented in
+Documentation/devicetree/bindings/mfd/zii,rave-sp.txt)
+
+Required properties:
+
+- compatible: Depending on wire protocol implemented by RAVE SP
+  firmware, should be one of:
+	- "zii,rave-sp-watchdog"
+	- "zii,rave-sp-watchdog-legacy"
+
+Optional properties:
+
+- wdt-timeout:	Two byte nvmem cell specified as per
+		Documentation/devicetree/bindings/nvmem/nvmem.txt
+
+Example:
+
+	rave-sp {
+		compatible = "zii,rave-sp-rdu1";
+		current-speed = <38400>;
+
+		eeprom {
+			wdt_timeout: wdt-timeout@8E {
+				reg = <0x8E 2>;
+			};
+		};
+
+		watchdog {
+			compatible = "zii,rave-sp-watchdog";
+			nvmem-cells = <&wdt_timeout>;
+			nvmem-cell-names = "wdt-timeout";
+		};
+	}
+
diff --git a/Documentation/devicetree/bindings/watchdog/ziirave-wdt.txt b/Documentation/devicetree/bindings/watchdog/ziirave-wdt.txt
new file mode 100644
index 000000000..3d878184e
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/ziirave-wdt.txt
@@ -0,0 +1,19 @@
+Zodiac RAVE Watchdog Timer
+
+Required properties:
+- compatible: must be "zii,rave-wdt"
+- reg: i2c slave address of device, usually 0x38
+
+Optional Properties:
+- timeout-sec: Watchdog timeout value in seconds.
+- reset-duration-ms: Duration of the pulse generated when the watchdog times
+  out. Value in milliseconds.
+
+Example:
+
+	watchdog@38 {
+		compatible = "zii,rave-wdt";
+		reg = <0x38>;
+		timeout-sec = <30>;
+		reset-duration-ms = <30>;
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
new file mode 100644
index 000000000..06ce67766
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
@@ -0,0 +1,32 @@
+ZTE zx2967 Watchdog timer
+
+Required properties:
+
+- compatible : should be one of the following.
+       * zte,zx296718-wdt
+- reg : Specifies base physical address and size of the registers.
+- clocks : Pairs of phandle and specifier referencing the controller's clocks.
+- resets : Reference to the reset controller controlling the watchdog
+           controller.
+
+Optional properties:
+
+- timeout-sec : Contains the watchdog timeout in seconds.
+- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
+	if we don't want to restart system when watchdog been triggered,
+	it's not required, vice versa.
+	It should include following fields.
+	  * phandle of aon-sysctrl.
+	  * offset of register that be written, should be 0xb0.
+	  * configure value that be written to aon-sysctrl.
+	  * bit mask, corresponding bits will be affected.
+
+Example:
+
+wdt: watchdog@1465000 {
+	compatible = "zte,zx296718-wdt";
+	reg = <0x1465000 0x1000>;
+	clocks = <&topcrm WDT_WCLK>;
+	resets = <&toprst 35>;
+	zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
+};