Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

6 files changed, 889 insertions, 0 deletions

diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
new file mode 100644
index 000000000..b40ee54a1
--- /dev/null
+++ b/drivers/phy/hisilicon/Kconfig
@@ -0,0 +1,40 @@
+#
+# Phy drivers for Hisilicon platforms
+#
+config PHY_HI6220_USB
+	tristate "hi6220 USB PHY support"
+	depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the HISILICON HI6220 USB PHY.
+
+	  To compile this driver as a module, choose M here.
+
+config PHY_HISTB_COMBPHY
+	tristate "HiSilicon STB SoCs COMBPHY support"
+	depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the HISILICON STB SoCs COMBPHY.
+	  If unsure, say N.
+
+config PHY_HISI_INNO_USB2
+       tristate "HiSilicon INNO USB2 PHY support"
+       depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+       select GENERIC_PHY
+       select MFD_SYSCON
+       help
+         Support for INNO USB2 PHY on HiSilicon SoCs. This Phy supports
+         USB 1.5Mb/s, USB 12Mb/s, USB 480Mb/s speeds. It supports one
+         USB host port to accept one USB device.
+
+config PHY_HIX5HD2_SATA
+	tristate "HIX5HD2 SATA PHY Driver"
+	depends on ARCH_HIX5HD2 && OF && HAS_IOMEM
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
new file mode 100644
index 000000000..f662a4fe1
--- /dev/null
+++ b/drivers/phy/hisilicon/Makefile
@@ -0,0 +1,4 @@
+obj-$(CONFIG_PHY_HI6220_USB)		+= phy-hi6220-usb.o
+obj-$(CONFIG_PHY_HISTB_COMBPHY)		+= phy-histb-combphy.o
+obj-$(CONFIG_PHY_HISI_INNO_USB2)	+= phy-hisi-inno-usb2.o
+obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
diff --git a/drivers/phy/hisilicon/phy-hi6220-usb.c b/drivers/phy/hisilicon/phy-hi6220-usb.c
new file mode 100644
index 000000000..398c1021d
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hi6220-usb.c
@@ -0,0 +1,168 @@
+/*
+ * Copyright (c) 2015 Linaro Ltd.
+ * Copyright (c) 2015 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+
+#define SC_PERIPH_CTRL4			0x00c
+
+#define CTRL4_PICO_SIDDQ		BIT(6)
+#define CTRL4_PICO_OGDISABLE		BIT(8)
+#define CTRL4_PICO_VBUSVLDEXT		BIT(10)
+#define CTRL4_PICO_VBUSVLDEXTSEL	BIT(11)
+#define CTRL4_OTG_PHY_SEL		BIT(21)
+
+#define SC_PERIPH_CTRL5			0x010
+
+#define CTRL5_USBOTG_RES_SEL		BIT(3)
+#define CTRL5_PICOPHY_ACAENB		BIT(4)
+#define CTRL5_PICOPHY_BC_MODE		BIT(5)
+#define CTRL5_PICOPHY_CHRGSEL		BIT(6)
+#define CTRL5_PICOPHY_VDATSRCEND	BIT(7)
+#define CTRL5_PICOPHY_VDATDETENB	BIT(8)
+#define CTRL5_PICOPHY_DCDENB		BIT(9)
+#define CTRL5_PICOPHY_IDDIG		BIT(10)
+
+#define SC_PERIPH_CTRL8			0x018
+#define SC_PERIPH_RSTEN0		0x300
+#define SC_PERIPH_RSTDIS0		0x304
+
+#define RST0_USBOTG_BUS			BIT(4)
+#define RST0_POR_PICOPHY		BIT(5)
+#define RST0_USBOTG			BIT(6)
+#define RST0_USBOTG_32K			BIT(7)
+
+#define EYE_PATTERN_PARA		0x7053348c
+
+struct hi6220_priv {
+	struct regmap *reg;
+	struct device *dev;
+};
+
+static void hi6220_phy_init(struct hi6220_priv *priv)
+{
+	struct regmap *reg = priv->reg;
+	u32 val, mask;
+
+	val = RST0_USBOTG_BUS | RST0_POR_PICOPHY |
+	      RST0_USBOTG | RST0_USBOTG_32K;
+	mask = val;
+	regmap_update_bits(reg, SC_PERIPH_RSTEN0, mask, val);
+	regmap_update_bits(reg, SC_PERIPH_RSTDIS0, mask, val);
+}
+
+static int hi6220_phy_setup(struct hi6220_priv *priv, bool on)
+{
+	struct regmap *reg = priv->reg;
+	u32 val, mask;
+	int ret;
+
+	if (on) {
+		val = CTRL5_USBOTG_RES_SEL | CTRL5_PICOPHY_ACAENB;
+		mask = val | CTRL5_PICOPHY_BC_MODE;
+		ret = regmap_update_bits(reg, SC_PERIPH_CTRL5, mask, val);
+		if (ret)
+			goto out;
+
+		val =  CTRL4_PICO_VBUSVLDEXT | CTRL4_PICO_VBUSVLDEXTSEL |
+		       CTRL4_OTG_PHY_SEL;
+		mask = val | CTRL4_PICO_SIDDQ | CTRL4_PICO_OGDISABLE;
+		ret = regmap_update_bits(reg, SC_PERIPH_CTRL4, mask, val);
+		if (ret)
+			goto out;
+
+		ret = regmap_write(reg, SC_PERIPH_CTRL8, EYE_PATTERN_PARA);
+		if (ret)
+			goto out;
+	} else {
+		val = CTRL4_PICO_SIDDQ;
+		mask = val;
+		ret = regmap_update_bits(reg, SC_PERIPH_CTRL4, mask, val);
+		if (ret)
+			goto out;
+	}
+
+	return 0;
+out:
+	dev_err(priv->dev, "failed to setup phy ret: %d\n", ret);
+	return ret;
+}
+
+static int hi6220_phy_start(struct phy *phy)
+{
+	struct hi6220_priv *priv = phy_get_drvdata(phy);
+
+	return hi6220_phy_setup(priv, true);
+}
+
+static int hi6220_phy_exit(struct phy *phy)
+{
+	struct hi6220_priv *priv = phy_get_drvdata(phy);
+
+	return hi6220_phy_setup(priv, false);
+}
+
+static const struct phy_ops hi6220_phy_ops = {
+	.init		= hi6220_phy_start,
+	.exit		= hi6220_phy_exit,
+	.owner		= THIS_MODULE,
+};
+
+static int hi6220_phy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+	struct phy *phy;
+	struct hi6220_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	priv->reg = syscon_regmap_lookup_by_phandle(dev->of_node,
+					"hisilicon,peripheral-syscon");
+	if (IS_ERR(priv->reg)) {
+		dev_err(dev, "no hisilicon,peripheral-syscon\n");
+		return PTR_ERR(priv->reg);
+	}
+
+	hi6220_phy_init(priv);
+
+	phy = devm_phy_create(dev, NULL, &hi6220_phy_ops);
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
+
+	phy_set_drvdata(phy, priv);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hi6220_phy_of_match[] = {
+	{.compatible = "hisilicon,hi6220-usb-phy",},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, hi6220_phy_of_match);
+
+static struct platform_driver hi6220_phy_driver = {
+	.probe	= hi6220_phy_probe,
+	.driver = {
+		.name	= "hi6220-usb-phy",
+		.of_match_table	= hi6220_phy_of_match,
+	}
+};
+module_platform_driver(hi6220_phy_driver);
+
+MODULE_DESCRIPTION("HISILICON HI6220 USB PHY driver");
+MODULE_ALIAS("platform:hi6220-usb-phy");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/hisilicon/phy-hisi-inno-usb2.c b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
new file mode 100644
index 000000000..524381249
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
@@ -0,0 +1,197 @@
+/*
+ * HiSilicon INNO USB2 PHY Driver.
+ *
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/reset.h>
+
+#define INNO_PHY_PORT_NUM	2
+#define REF_CLK_STABLE_TIME	100	/* unit:us */
+#define UTMI_CLK_STABLE_TIME	200	/* unit:us */
+#define TEST_CLK_STABLE_TIME	2	/* unit:ms */
+#define PHY_CLK_STABLE_TIME	2	/* unit:ms */
+#define UTMI_RST_COMPLETE_TIME	2	/* unit:ms */
+#define POR_RST_COMPLETE_TIME	300	/* unit:us */
+#define PHY_TEST_DATA		GENMASK(7, 0)
+#define PHY_TEST_ADDR		GENMASK(15, 8)
+#define PHY_TEST_PORT		GENMASK(18, 16)
+#define PHY_TEST_WREN		BIT(21)
+#define PHY_TEST_CLK		BIT(22)	/* rising edge active */
+#define PHY_TEST_RST		BIT(23)	/* low active */
+#define PHY_CLK_ENABLE		BIT(2)
+
+struct hisi_inno_phy_port {
+	struct reset_control *utmi_rst;
+	struct hisi_inno_phy_priv *priv;
+};
+
+struct hisi_inno_phy_priv {
+	void __iomem *mmio;
+	struct clk *ref_clk;
+	struct reset_control *por_rst;
+	struct hisi_inno_phy_port ports[INNO_PHY_PORT_NUM];
+};
+
+static void hisi_inno_phy_write_reg(struct hisi_inno_phy_priv *priv,
+				    u8 port, u32 addr, u32 data)
+{
+	void __iomem *reg = priv->mmio;
+	u32 val;
+
+	val = (data & PHY_TEST_DATA) |
+	      ((addr << 8) & PHY_TEST_ADDR) |
+	      ((port << 16) & PHY_TEST_PORT) |
+	      PHY_TEST_WREN | PHY_TEST_RST;
+	writel(val, reg);
+
+	val |= PHY_TEST_CLK;
+	writel(val, reg);
+
+	val &= ~PHY_TEST_CLK;
+	writel(val, reg);
+}
+
+static void hisi_inno_phy_setup(struct hisi_inno_phy_priv *priv)
+{
+	/* The phy clk is controlled by the port0 register 0x06. */
+	hisi_inno_phy_write_reg(priv, 0, 0x06, PHY_CLK_ENABLE);
+	msleep(PHY_CLK_STABLE_TIME);
+}
+
+static int hisi_inno_phy_init(struct phy *phy)
+{
+	struct hisi_inno_phy_port *port = phy_get_drvdata(phy);
+	struct hisi_inno_phy_priv *priv = port->priv;
+	int ret;
+
+	ret = clk_prepare_enable(priv->ref_clk);
+	if (ret)
+		return ret;
+	udelay(REF_CLK_STABLE_TIME);
+
+	reset_control_deassert(priv->por_rst);
+	udelay(POR_RST_COMPLETE_TIME);
+
+	/* Set up phy registers */
+	hisi_inno_phy_setup(priv);
+
+	reset_control_deassert(port->utmi_rst);
+	udelay(UTMI_RST_COMPLETE_TIME);
+
+	return 0;
+}
+
+static int hisi_inno_phy_exit(struct phy *phy)
+{
+	struct hisi_inno_phy_port *port = phy_get_drvdata(phy);
+	struct hisi_inno_phy_priv *priv = port->priv;
+
+	reset_control_assert(port->utmi_rst);
+	reset_control_assert(priv->por_rst);
+	clk_disable_unprepare(priv->ref_clk);
+
+	return 0;
+}
+
+static const struct phy_ops hisi_inno_phy_ops = {
+	.init = hisi_inno_phy_init,
+	.exit = hisi_inno_phy_exit,
+	.owner = THIS_MODULE,
+};
+
+static int hisi_inno_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct hisi_inno_phy_priv *priv;
+	struct phy_provider *provider;
+	struct device_node *child;
+	struct resource *res;
+	int i = 0;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->mmio = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->mmio)) {
+		ret = PTR_ERR(priv->mmio);
+		return ret;
+	}
+
+	priv->ref_clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->ref_clk))
+		return PTR_ERR(priv->ref_clk);
+
+	priv->por_rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(priv->por_rst))
+		return PTR_ERR(priv->por_rst);
+
+	for_each_child_of_node(np, child) {
+		struct reset_control *rst;
+		struct phy *phy;
+
+		rst = of_reset_control_get_exclusive(child, NULL);
+		if (IS_ERR(rst))
+			return PTR_ERR(rst);
+		priv->ports[i].utmi_rst = rst;
+		priv->ports[i].priv = priv;
+
+		phy = devm_phy_create(dev, child, &hisi_inno_phy_ops);
+		if (IS_ERR(phy))
+			return PTR_ERR(phy);
+
+		phy_set_bus_width(phy, 8);
+		phy_set_drvdata(phy, &priv->ports[i]);
+		i++;
+
+		if (i > INNO_PHY_PORT_NUM) {
+			dev_warn(dev, "Support %d ports in maximum\n", i);
+			break;
+		}
+	}
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id hisi_inno_phy_of_match[] = {
+	{ .compatible = "hisilicon,inno-usb2-phy", },
+	{ .compatible = "hisilicon,hi3798cv200-usb2-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, hisi_inno_phy_of_match);
+
+static struct platform_driver hisi_inno_phy_driver = {
+	.probe	= hisi_inno_phy_probe,
+	.driver = {
+		.name	= "hisi-inno-phy",
+		.of_match_table	= hisi_inno_phy_of_match,
+	}
+};
+module_platform_driver(hisi_inno_phy_driver);
+
+MODULE_DESCRIPTION("HiSilicon INNO USB2 PHY Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/hisilicon/phy-histb-combphy.c b/drivers/phy/hisilicon/phy-histb-combphy.c
new file mode 100644
index 000000000..5777b3120
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-histb-combphy.c
@@ -0,0 +1,289 @@
+/*
+ * COMBPHY driver for HiSilicon STB SoCs
+ *
+ * Copyright (C) 2016-2017 HiSilicon Co., Ltd. http://www.hisilicon.com
+ *
+ * Authors: Jianguo Sun <sunjianguo1@huawei.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <dt-bindings/phy/phy.h>
+
+#define COMBPHY_MODE_PCIE		0
+#define COMBPHY_MODE_USB3		1
+#define COMBPHY_MODE_SATA		2
+
+#define COMBPHY_CFG_REG			0x0
+#define COMBPHY_BYPASS_CODEC		BIT(31)
+#define COMBPHY_TEST_WRITE		BIT(24)
+#define COMBPHY_TEST_DATA_SHIFT		20
+#define COMBPHY_TEST_DATA_MASK		GENMASK(23, 20)
+#define COMBPHY_TEST_ADDR_SHIFT		12
+#define COMBPHY_TEST_ADDR_MASK		GENMASK(16, 12)
+#define COMBPHY_CLKREF_OUT_OEN		BIT(0)
+
+struct histb_combphy_mode {
+	int fixed;
+	int select;
+	u32 reg;
+	u32 shift;
+	u32 mask;
+};
+
+struct histb_combphy_priv {
+	void __iomem *mmio;
+	struct regmap *syscon;
+	struct reset_control *por_rst;
+	struct clk *ref_clk;
+	struct phy *phy;
+	struct histb_combphy_mode mode;
+};
+
+static void nano_register_write(struct histb_combphy_priv *priv,
+				u32 addr, u32 data)
+{
+	void __iomem *reg = priv->mmio + COMBPHY_CFG_REG;
+	u32 val;
+
+	/* Set up address and data for the write */
+	val = readl(reg);
+	val &= ~COMBPHY_TEST_ADDR_MASK;
+	val |= addr << COMBPHY_TEST_ADDR_SHIFT;
+	val &= ~COMBPHY_TEST_DATA_MASK;
+	val |= data << COMBPHY_TEST_DATA_SHIFT;
+	writel(val, reg);
+
+	/* Flip strobe control to trigger the write */
+	val &= ~COMBPHY_TEST_WRITE;
+	writel(val, reg);
+	val |= COMBPHY_TEST_WRITE;
+	writel(val, reg);
+}
+
+static int is_mode_fixed(struct histb_combphy_mode *mode)
+{
+	return (mode->fixed != PHY_NONE) ? true : false;
+}
+
+static int histb_combphy_set_mode(struct histb_combphy_priv *priv)
+{
+	struct histb_combphy_mode *mode = &priv->mode;
+	struct regmap *syscon = priv->syscon;
+	u32 hw_sel;
+
+	if (is_mode_fixed(mode))
+		return 0;
+
+	switch (mode->select) {
+	case PHY_TYPE_SATA:
+		hw_sel = COMBPHY_MODE_SATA;
+		break;
+	case PHY_TYPE_PCIE:
+		hw_sel = COMBPHY_MODE_PCIE;
+		break;
+	case PHY_TYPE_USB3:
+		hw_sel = COMBPHY_MODE_USB3;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(syscon, mode->reg, mode->mask,
+				  hw_sel << mode->shift);
+}
+
+static int histb_combphy_init(struct phy *phy)
+{
+	struct histb_combphy_priv *priv = phy_get_drvdata(phy);
+	u32 val;
+	int ret;
+
+	ret = histb_combphy_set_mode(priv);
+	if (ret)
+		return ret;
+
+	/* Clear bypass bit to enable encoding/decoding */
+	val = readl(priv->mmio + COMBPHY_CFG_REG);
+	val &= ~COMBPHY_BYPASS_CODEC;
+	writel(val, priv->mmio + COMBPHY_CFG_REG);
+
+	ret = clk_prepare_enable(priv->ref_clk);
+	if (ret)
+		return ret;
+
+	reset_control_deassert(priv->por_rst);
+
+	/* Enable EP clock */
+	val = readl(priv->mmio + COMBPHY_CFG_REG);
+	val |= COMBPHY_CLKREF_OUT_OEN;
+	writel(val, priv->mmio + COMBPHY_CFG_REG);
+
+	/* Need to wait for EP clock stable */
+	mdelay(5);
+
+	/* Configure nano phy registers as suggested by vendor */
+	nano_register_write(priv, 0x1, 0x8);
+	nano_register_write(priv, 0xc, 0x9);
+	nano_register_write(priv, 0x1a, 0x4);
+
+	return 0;
+}
+
+static int histb_combphy_exit(struct phy *phy)
+{
+	struct histb_combphy_priv *priv = phy_get_drvdata(phy);
+	u32 val;
+
+	/* Disable EP clock */
+	val = readl(priv->mmio + COMBPHY_CFG_REG);
+	val &= ~COMBPHY_CLKREF_OUT_OEN;
+	writel(val, priv->mmio + COMBPHY_CFG_REG);
+
+	reset_control_assert(priv->por_rst);
+	clk_disable_unprepare(priv->ref_clk);
+
+	return 0;
+}
+
+static const struct phy_ops histb_combphy_ops = {
+	.init = histb_combphy_init,
+	.exit = histb_combphy_exit,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *histb_combphy_xlate(struct device *dev,
+				       struct of_phandle_args *args)
+{
+	struct histb_combphy_priv *priv = dev_get_drvdata(dev);
+	struct histb_combphy_mode *mode = &priv->mode;
+
+	if (args->args_count < 1) {
+		dev_err(dev, "invalid number of arguments\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	mode->select = args->args[0];
+
+	if (mode->select < PHY_TYPE_SATA || mode->select > PHY_TYPE_USB3) {
+		dev_err(dev, "invalid phy mode select argument\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (is_mode_fixed(mode) && mode->select != mode->fixed) {
+		dev_err(dev, "mode select %d mismatch fixed phy mode %d\n",
+			mode->select, mode->fixed);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return priv->phy;
+}
+
+static int histb_combphy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+	struct histb_combphy_priv *priv;
+	struct device_node *np = dev->of_node;
+	struct histb_combphy_mode *mode;
+	struct resource *res;
+	u32 vals[3];
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->mmio = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->mmio)) {
+		ret = PTR_ERR(priv->mmio);
+		return ret;
+	}
+
+	priv->syscon = syscon_node_to_regmap(np->parent);
+	if (IS_ERR(priv->syscon)) {
+		dev_err(dev, "failed to find peri_ctrl syscon regmap\n");
+		return PTR_ERR(priv->syscon);
+	}
+
+	mode = &priv->mode;
+	mode->fixed = PHY_NONE;
+
+	ret = of_property_read_u32(np, "hisilicon,fixed-mode", &mode->fixed);
+	if (ret == 0)
+		dev_dbg(dev, "found fixed phy mode %d\n", mode->fixed);
+
+	ret = of_property_read_u32_array(np, "hisilicon,mode-select-bits",
+					 vals, ARRAY_SIZE(vals));
+	if (ret == 0) {
+		if (is_mode_fixed(mode)) {
+			dev_err(dev, "found select bits for fixed mode phy\n");
+			return -EINVAL;
+		}
+
+		mode->reg = vals[0];
+		mode->shift = vals[1];
+		mode->mask = vals[2];
+		dev_dbg(dev, "found mode select bits\n");
+	} else {
+		if (!is_mode_fixed(mode)) {
+			dev_err(dev, "no valid select bits found for non-fixed phy\n");
+			return -ENODEV;
+		}
+	}
+
+	priv->ref_clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->ref_clk)) {
+		dev_err(dev, "failed to find ref clock\n");
+		return PTR_ERR(priv->ref_clk);
+	}
+
+	priv->por_rst = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(priv->por_rst)) {
+		dev_err(dev, "failed to get poweron reset\n");
+		return PTR_ERR(priv->por_rst);
+	}
+
+	priv->phy = devm_phy_create(dev, NULL, &histb_combphy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create combphy\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+
+	phy_provider = devm_of_phy_provider_register(dev, histb_combphy_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id histb_combphy_of_match[] = {
+	{ .compatible = "hisilicon,hi3798cv200-combphy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, histb_combphy_of_match);
+
+static struct platform_driver histb_combphy_driver = {
+	.probe	= histb_combphy_probe,
+	.driver = {
+		.name = "combphy",
+		.of_match_table = histb_combphy_of_match,
+	},
+};
+module_platform_driver(histb_combphy_driver);
+
+MODULE_DESCRIPTION("HiSilicon STB COMBPHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/hisilicon/phy-hix5hd2-sata.c b/drivers/phy/hisilicon/phy-hix5hd2-sata.c
new file mode 100644
index 000000000..e5ab3aa78
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hix5hd2-sata.c
@@ -0,0 +1,191 @@
+/*
+ * Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define SATA_PHY0_CTLL		0xa0
+#define MPLL_MULTIPLIER_SHIFT	1
+#define MPLL_MULTIPLIER_MASK	0xfe
+#define MPLL_MULTIPLIER_50M	0x3c
+#define MPLL_MULTIPLIER_100M	0x1e
+#define PHY_RESET		BIT(0)
+#define REF_SSP_EN		BIT(9)
+#define SSC_EN			BIT(10)
+#define REF_USE_PAD		BIT(23)
+
+#define SATA_PORT_PHYCTL	0x174
+#define SPEED_MODE_MASK		0x6f0000
+#define HALF_RATE_SHIFT		16
+#define PHY_CONFIG_SHIFT	18
+#define GEN2_EN_SHIFT		21
+#define SPEED_CTRL		BIT(20)
+
+#define SATA_PORT_PHYCTL1	0x148
+#define AMPLITUDE_MASK		0x3ffffe
+#define AMPLITUDE_GEN3		0x68
+#define AMPLITUDE_GEN3_SHIFT	15
+#define AMPLITUDE_GEN2		0x56
+#define AMPLITUDE_GEN2_SHIFT	8
+#define AMPLITUDE_GEN1		0x56
+#define AMPLITUDE_GEN1_SHIFT	1
+
+#define SATA_PORT_PHYCTL2	0x14c
+#define PREEMPH_MASK		0x3ffff
+#define PREEMPH_GEN3		0x20
+#define PREEMPH_GEN3_SHIFT	12
+#define PREEMPH_GEN2		0x15
+#define PREEMPH_GEN2_SHIFT	6
+#define PREEMPH_GEN1		0x5
+#define PREEMPH_GEN1_SHIFT	0
+
+struct hix5hd2_priv {
+	void __iomem	*base;
+	struct regmap	*peri_ctrl;
+};
+
+enum phy_speed_mode {
+	SPEED_MODE_GEN1 = 0,
+	SPEED_MODE_GEN2 = 1,
+	SPEED_MODE_GEN3 = 2,
+};
+
+static int hix5hd2_sata_phy_init(struct phy *phy)
+{
+	struct hix5hd2_priv *priv = phy_get_drvdata(phy);
+	u32 val, data[2];
+	int ret;
+
+	if (priv->peri_ctrl) {
+		ret = of_property_read_u32_array(phy->dev.of_node,
+						 "hisilicon,power-reg",
+						 &data[0], 2);
+		if (ret) {
+			dev_err(&phy->dev, "Fail read hisilicon,power-reg\n");
+			return ret;
+		}
+
+		regmap_update_bits(priv->peri_ctrl, data[0],
+				   BIT(data[1]), BIT(data[1]));
+	}
+
+	/* reset phy */
+	val = readl_relaxed(priv->base + SATA_PHY0_CTLL);
+	val &= ~(MPLL_MULTIPLIER_MASK | REF_USE_PAD);
+	val |= MPLL_MULTIPLIER_50M << MPLL_MULTIPLIER_SHIFT |
+	       REF_SSP_EN | PHY_RESET;
+	writel_relaxed(val, priv->base + SATA_PHY0_CTLL);
+	msleep(20);
+	val &= ~PHY_RESET;
+	writel_relaxed(val, priv->base + SATA_PHY0_CTLL);
+
+	val = readl_relaxed(priv->base + SATA_PORT_PHYCTL1);
+	val &= ~AMPLITUDE_MASK;
+	val |= AMPLITUDE_GEN3 << AMPLITUDE_GEN3_SHIFT |
+	       AMPLITUDE_GEN2 << AMPLITUDE_GEN2_SHIFT |
+	       AMPLITUDE_GEN1 << AMPLITUDE_GEN1_SHIFT;
+	writel_relaxed(val, priv->base + SATA_PORT_PHYCTL1);
+
+	val = readl_relaxed(priv->base + SATA_PORT_PHYCTL2);
+	val &= ~PREEMPH_MASK;
+	val |= PREEMPH_GEN3 << PREEMPH_GEN3_SHIFT |
+	       PREEMPH_GEN2 << PREEMPH_GEN2_SHIFT |
+	       PREEMPH_GEN1 << PREEMPH_GEN1_SHIFT;
+	writel_relaxed(val, priv->base + SATA_PORT_PHYCTL2);
+
+	/* ensure PHYCTRL setting takes effect */
+	val = readl_relaxed(priv->base + SATA_PORT_PHYCTL);
+	val &= ~SPEED_MODE_MASK;
+	val |= SPEED_MODE_GEN1 << HALF_RATE_SHIFT |
+	       SPEED_MODE_GEN1 << PHY_CONFIG_SHIFT |
+	       SPEED_MODE_GEN1 << GEN2_EN_SHIFT | SPEED_CTRL;
+	writel_relaxed(val, priv->base + SATA_PORT_PHYCTL);
+
+	msleep(20);
+	val &= ~SPEED_MODE_MASK;
+	val |= SPEED_MODE_GEN3 << HALF_RATE_SHIFT |
+	       SPEED_MODE_GEN3 << PHY_CONFIG_SHIFT |
+	       SPEED_MODE_GEN3 << GEN2_EN_SHIFT | SPEED_CTRL;
+	writel_relaxed(val, priv->base + SATA_PORT_PHYCTL);
+
+	val &= ~(SPEED_MODE_MASK | SPEED_CTRL);
+	val |= SPEED_MODE_GEN2 << HALF_RATE_SHIFT |
+	       SPEED_MODE_GEN2 << PHY_CONFIG_SHIFT |
+	       SPEED_MODE_GEN2 << GEN2_EN_SHIFT;
+	writel_relaxed(val, priv->base + SATA_PORT_PHYCTL);
+
+	return 0;
+}
+
+static const struct phy_ops hix5hd2_sata_phy_ops = {
+	.init		= hix5hd2_sata_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int hix5hd2_sata_phy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct phy *phy;
+	struct hix5hd2_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
+
+	priv->base = devm_ioremap(dev, res->start, resource_size(res));
+	if (!priv->base)
+		return -ENOMEM;
+
+	priv->peri_ctrl = syscon_regmap_lookup_by_phandle(dev->of_node,
+					"hisilicon,peripheral-syscon");
+	if (IS_ERR(priv->peri_ctrl))
+		priv->peri_ctrl = NULL;
+
+	phy = devm_phy_create(dev, NULL, &hix5hd2_sata_phy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_set_drvdata(phy, priv);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id hix5hd2_sata_phy_of_match[] = {
+	{.compatible = "hisilicon,hix5hd2-sata-phy",},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, hix5hd2_sata_phy_of_match);
+
+static struct platform_driver hix5hd2_sata_phy_driver = {
+	.probe	= hix5hd2_sata_phy_probe,
+	.driver = {
+		.name	= "hix5hd2-sata-phy",
+		.of_match_table	= hix5hd2_sata_phy_of_match,
+	}
+};
+module_platform_driver(hix5hd2_sata_phy_driver);
+
+MODULE_AUTHOR("Jiancheng Xue <xuejiancheng@huawei.com>");
+MODULE_DESCRIPTION("HISILICON HIX5HD2 SATA PHY driver");
+MODULE_ALIAS("platform:hix5hd2-sata-phy");
+MODULE_LICENSE("GPL v2");