Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 321 insertions, 0 deletions

diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
new file mode 100644
index 000000000..cc4f0c5e5
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -0,0 +1,321 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Mediatek 8250 driver.
+ *
+ * Copyright (c) 2014 MundoReader S.L.
+ * Author: Matthias Brugger <matthias.bgg@gmail.com>
+ */
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include "8250.h"
+
+#define UART_MTK_HIGHS		0x09	/* Highspeed register */
+#define UART_MTK_SAMPLE_COUNT	0x0a	/* Sample count register */
+#define UART_MTK_SAMPLE_POINT	0x0b	/* Sample point register */
+#define MTK_UART_RATE_FIX	0x0d	/* UART Rate Fix Register */
+
+struct mtk8250_data {
+	int			line;
+	struct clk		*uart_clk;
+	struct clk		*bus_clk;
+};
+
+static void
+mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
+			struct ktermios *old)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned long flags;
+	unsigned int baud, quot;
+
+	/*
+	 * Store the requested baud rate before calling the generic 8250
+	 * set_termios method. Standard 8250 port expects bauds to be
+	 * no higher than (uartclk / 16) so the baud will be clamped if it
+	 * gets out of that bound. Mediatek 8250 port supports speed
+	 * higher than that, therefore we'll get original baud rate back
+	 * after calling the generic set_termios method and recalculate
+	 * the speed later in this method.
+	 */
+	baud = tty_termios_baud_rate(termios);
+
+	serial8250_do_set_termios(port, termios, NULL);
+
+	tty_termios_encode_baud_rate(termios, baud, baud);
+
+	/*
+	 * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
+	 *
+	 * We need to recalcualte the quot register, as the claculation depends
+	 * on the vaule in the highspeed register.
+	 *
+	 * Some baudrates are not supported by the chip, so we use the next
+	 * lower rate supported and update termios c_flag.
+	 *
+	 * If highspeed register is set to 3, we need to specify sample count
+	 * and sample point to increase accuracy. If not, we reset the
+	 * registers to their default values.
+	 */
+	baud = uart_get_baud_rate(port, termios, old,
+				  port->uartclk / 16 / UART_DIV_MAX,
+				  port->uartclk);
+
+	if (baud <= 115200) {
+		serial_port_out(port, UART_MTK_HIGHS, 0x0);
+		quot = uart_get_divisor(port, baud);
+	} else if (baud <= 576000) {
+		serial_port_out(port, UART_MTK_HIGHS, 0x2);
+
+		/* Set to next lower baudrate supported */
+		if ((baud == 500000) || (baud == 576000))
+			baud = 460800;
+		quot = DIV_ROUND_UP(port->uartclk, 4 * baud);
+	} else {
+		serial_port_out(port, UART_MTK_HIGHS, 0x3);
+		quot = DIV_ROUND_UP(port->uartclk, 256 * baud);
+	}
+
+	/*
+	 * Ok, we're now changing the port state.  Do it with
+	 * interrupts disabled.
+	 */
+	spin_lock_irqsave(&port->lock, flags);
+
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	/* set DLAB we have cval saved in up->lcr from the call to the core */
+	serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
+	serial_dl_write(up, quot);
+
+	/* reset DLAB */
+	serial_port_out(port, UART_LCR, up->lcr);
+
+	if (baud > 460800) {
+		unsigned int tmp;
+
+		tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud);
+		serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1);
+		serial_port_out(port, UART_MTK_SAMPLE_POINT,
+					(tmp - 2) >> 1);
+	} else {
+		serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00);
+		serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff);
+	}
+
+	spin_unlock_irqrestore(&port->lock, flags);
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+}
+
+static int __maybe_unused mtk8250_runtime_suspend(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(data->uart_clk);
+	clk_disable_unprepare(data->bus_clk);
+
+	return 0;
+}
+
+static int __maybe_unused mtk8250_runtime_resume(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+	int err;
+
+	err = clk_prepare_enable(data->uart_clk);
+	if (err) {
+		dev_warn(dev, "Can't enable clock\n");
+		return err;
+	}
+
+	err = clk_prepare_enable(data->bus_clk);
+	if (err) {
+		dev_warn(dev, "Can't enable bus clock\n");
+		return err;
+	}
+
+	return 0;
+}
+
+static void
+mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
+{
+	if (!state)
+		pm_runtime_get_sync(port->dev);
+
+	serial8250_do_pm(port, state, old);
+
+	if (state)
+		pm_runtime_put_sync_suspend(port->dev);
+}
+
+static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p,
+			   struct mtk8250_data *data)
+{
+	data->uart_clk = devm_clk_get(&pdev->dev, "baud");
+	if (IS_ERR(data->uart_clk)) {
+		/*
+		 * For compatibility with older device trees try unnamed
+		 * clk when no baud clk can be found.
+		 */
+		data->uart_clk = devm_clk_get(&pdev->dev, NULL);
+		if (IS_ERR(data->uart_clk)) {
+			dev_warn(&pdev->dev, "Can't get uart clock\n");
+			return PTR_ERR(data->uart_clk);
+		}
+
+		return 0;
+	}
+
+	data->bus_clk = devm_clk_get(&pdev->dev, "bus");
+	return PTR_ERR_OR_ZERO(data->bus_clk);
+}
+
+static int mtk8250_probe(struct platform_device *pdev)
+{
+	struct uart_8250_port uart = {};
+	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	struct mtk8250_data *data;
+	int err;
+
+	if (!regs || !irq) {
+		dev_err(&pdev->dev, "no registers/irq defined\n");
+		return -EINVAL;
+	}
+
+	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+					 resource_size(regs));
+	if (!uart.port.membase)
+		return -ENOMEM;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	if (pdev->dev.of_node) {
+		err = mtk8250_probe_of(pdev, &uart.port, data);
+		if (err)
+			return err;
+	} else
+		return -ENODEV;
+
+	spin_lock_init(&uart.port.lock);
+	uart.port.mapbase = regs->start;
+	uart.port.irq = irq->start;
+	uart.port.pm = mtk8250_do_pm;
+	uart.port.type = PORT_16550;
+	uart.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
+	uart.port.dev = &pdev->dev;
+	uart.port.iotype = UPIO_MEM32;
+	uart.port.regshift = 2;
+	uart.port.private_data = data;
+	uart.port.set_termios = mtk8250_set_termios;
+	uart.port.uartclk = clk_get_rate(data->uart_clk);
+
+	/* Disable Rate Fix function */
+	writel(0x0, uart.port.membase +
+			(MTK_UART_RATE_FIX << uart.port.regshift));
+
+	platform_set_drvdata(pdev, data);
+
+	err = mtk8250_runtime_resume(&pdev->dev);
+	if (err)
+		return err;
+
+	data->line = serial8250_register_8250_port(&uart);
+	if (data->line < 0)
+		return data->line;
+
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
+	return 0;
+}
+
+static int mtk8250_remove(struct platform_device *pdev)
+{
+	struct mtk8250_data *data = platform_get_drvdata(pdev);
+
+	pm_runtime_get_sync(&pdev->dev);
+
+	serial8250_unregister_port(data->line);
+	mtk8250_runtime_suspend(&pdev->dev);
+
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+
+	return 0;
+}
+
+static int __maybe_unused mtk8250_suspend(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	serial8250_suspend_port(data->line);
+
+	return 0;
+}
+
+static int __maybe_unused mtk8250_resume(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	serial8250_resume_port(data->line);
+
+	return 0;
+}
+
+static const struct dev_pm_ops mtk8250_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
+	SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
+				NULL)
+};
+
+static const struct of_device_id mtk8250_of_match[] = {
+	{ .compatible = "mediatek,mt6577-uart" },
+	{ /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mtk8250_of_match);
+
+static struct platform_driver mtk8250_platform_driver = {
+	.driver = {
+		.name		= "mt6577-uart",
+		.pm		= &mtk8250_pm_ops,
+		.of_match_table	= mtk8250_of_match,
+	},
+	.probe			= mtk8250_probe,
+	.remove			= mtk8250_remove,
+};
+module_platform_driver(mtk8250_platform_driver);
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init early_mtk8250_setup(struct earlycon_device *device,
+					const char *options)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->port.iotype = UPIO_MEM32;
+
+	return early_serial8250_setup(device, NULL);
+}
+
+OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup);
+#endif
+
+MODULE_AUTHOR("Matthias Brugger");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Mediatek 8250 serial port driver");