diff options
Diffstat (limited to 'Documentation/devicetree/bindings/arm/bcm')
17 files changed, 695 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt new file mode 100644 index 000000000..e3f996920 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method.txt @@ -0,0 +1,36 @@ +Broadcom Kona Family CPU Enable Method +-------------------------------------- +This binding defines the enable method used for starting secondary +CPUs in the following Broadcom SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155, BCM21664 + +The enable method is specified by defining the following required +properties in the "cpu" device tree node: + - enable-method = "brcm,bcm11351-cpu-method"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register used to request the ROM holding pen +code release a secondary CPU. The value written to the register is +formed by encoding the target CPU id into the low bits of the +physical start address it should jump to. + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + enable-method = "brcm,bcm11351-cpu-method"; + secondary-boot-reg = <0x3500417c>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351.txt new file mode 100644 index 000000000..0ff6560e6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351.txt @@ -0,0 +1,10 @@ +Broadcom BCM11351 device tree bindings +------------------------------------------- + +Boards with the bcm281xx SoC family (which includes bcm11130, bcm11140, +bcm11351, bcm28145, bcm28155 SoCs) shall have the following properties: + +Required root node property: + +compatible = "brcm,bcm11351"; +DEPRECATED: compatible = "bcm,bcm11351"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm21664.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm21664.txt new file mode 100644 index 000000000..e0774255e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm21664.txt @@ -0,0 +1,15 @@ +Broadcom BCM21664 device tree bindings +-------------------------------------- + +This document describes the device tree bindings for boards with the BCM21664 +SoC. + +Required root node property: + - compatible: brcm,bcm21664 + +Example: + / { + model = "BCM21664 SoC"; + compatible = "brcm,bcm21664"; + [...] + } diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550-cpu-method.txt new file mode 100644 index 000000000..a3af54c0e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550-cpu-method.txt @@ -0,0 +1,36 @@ +Broadcom Kona Family CPU Enable Method +-------------------------------------- +This binding defines the enable method used for starting secondary +CPUs in the following Broadcom SoCs: + BCM23550 + +The enable method is specified by defining the following required +properties in the "cpu" device tree node: + - enable-method = "brcm,bcm23550"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register used to request the ROM holding pen +code release a secondary CPU. The value written to the register is +formed by encoding the target CPU id into the low bits of the +physical start address it should jump to. + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + enable-method = "brcm,bcm23550"; + secondary-boot-reg = <0x3500417c>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550.txt new file mode 100644 index 000000000..080baad92 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm23550.txt @@ -0,0 +1,15 @@ +Broadcom BCM23550 device tree bindings +-------------------------------------- + +This document describes the device tree bindings for boards with the BCM23550 +SoC. + +Required root node property: + - compatible: brcm,bcm23550 + +Example: + / { + model = "BCM23550 SoC"; + compatible = "brcm,bcm23550"; + [...] + } diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt new file mode 100644 index 000000000..1e3e29a54 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -0,0 +1,55 @@ +Broadcom BCM2835 device tree bindings +------------------------------------------- + +Raspberry Pi Model A +Required root node properties: +compatible = "raspberrypi,model-a", "brcm,bcm2835"; + +Raspberry Pi Model A+ +Required root node properties: +compatible = "raspberrypi,model-a-plus", "brcm,bcm2835"; + +Raspberry Pi Model B +Required root node properties: +compatible = "raspberrypi,model-b", "brcm,bcm2835"; + +Raspberry Pi Model B (no P5) +early model B with I2C0 rather than I2C1 routed to the expansion header +Required root node properties: +compatible = "raspberrypi,model-b-i2c0", "brcm,bcm2835"; + +Raspberry Pi Model B rev2 +Required root node properties: +compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; + +Raspberry Pi Model B+ +Required root node properties: +compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; + +Raspberry Pi 2 Model B +Required root node properties: +compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; + +Raspberry Pi 3 Model B +Required root node properties: +compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; + +Raspberry Pi 3 Model B+ +Required root node properties: +compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; + +Raspberry Pi Compute Module +Required root node properties: +compatible = "raspberrypi,compute-module", "brcm,bcm2835"; + +Raspberry Pi Zero +Required root node properties: +compatible = "raspberrypi,model-zero", "brcm,bcm2835"; + +Raspberry Pi Zero W +Required root node properties: +compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; + +Generic BCM2835 board +Required root node properties: +compatible = "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt new file mode 100644 index 000000000..8608a776c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4708.txt @@ -0,0 +1,15 @@ +Broadcom BCM4708 device tree bindings +------------------------------------------- + +Boards with the BCM4708 SoC shall have the following properties: + +Required root node property: + +bcm4708 +compatible = "brcm,bcm4708"; + +bcm4709 +compatible = "brcm,bcm4709"; + +bcm53012 +compatible = "brcm,bcm53012"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt new file mode 100644 index 000000000..b82b6a0ae --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt @@ -0,0 +1,85 @@ +Broadcom BCM63138 DSL System-on-a-Chip device tree bindings +----------------------------------------------------------- + +Boards compatible with the BCM63138 DSL System-on-a-Chip should have the +following properties: + +Required root node property: + +compatible: should be "brcm,bcm63138" + +An optional Boot lookup table Device Tree node is required for secondary CPU +initialization as well as a 'resets' phandle to the correct PMB controller as +defined in reset/brcm,bcm63138-pmb.txt for this secondary CPU, and an +'enable-method' property. + +Required properties for the Boot lookup table node: +- compatible: should be "brcm,bcm63138-bootlut" +- reg: register base address and length for the Boot Lookup table + +Optional properties for the primary CPU node: +- enable-method: should be "brcm,bcm63138" + +Optional properties for the secondary CPU node: +- enable-method: should be "brcm,bcm63138" +- resets: phandle to the relevant PMB controller, one integer indicating the internal + bus number, and a second integer indicating the address of the CPU in the PMB + internal bus number. + +Example: + + cpus { + cpu@0 { + compatible = "arm,cotex-a9"; + reg = <0>; + ... + enable-method = "brcm,bcm63138"; + }; + + cpu@1 { + compatible = "arm,cortex-a9"; + reg = <1>; + ... + enable-method = "brcm,bcm63138"; + resets = <&pmb0 4 1>; + }; + }; + + bootlut: bootlut@8000 { + compatible = "brcm,bcm63138-bootlut"; + reg = <0x8000 0x50>; + }; + +======= +reboot +------ +Two nodes are required for software reboot: a timer node and a syscon-reboot node. + +Timer node: + +- compatible: Must be "brcm,bcm6328-timer", "syscon" +- reg: Register base address and length + +Syscon reboot node: + +See Documentation/devicetree/bindings/power/reset/syscon-reboot.txt for the +detailed list of properties, the two values defined below are specific to the +BCM6328-style timer: + +- offset: Should be 0x34 to denote the offset of the TIMER_WD_TIMER_RESET register + from the beginning of the TIMER block +- mask: Should be 1 for the SoftRst bit. + +Example: + + timer: timer@80 { + compatible = "brcm,bcm6328-timer", "syscon"; + reg = <0x80 0x3c>; + }; + + reboot { + compatible = "syscon-reboot"; + regmap = <&timer>; + offset = <0x34>; + mask = <0x1>; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt new file mode 100644 index 000000000..104cc9b41 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt @@ -0,0 +1,265 @@ +ARM Broadcom STB platforms Device Tree Bindings +----------------------------------------------- +Boards with Broadcom Brahma15 ARM-based BCMxxxx (generally BCM7xxx variants) +SoC shall have the following DT organization: + +Required root node properties: + - compatible: "brcm,bcm<chip_id>", "brcm,brcmstb" + +example: +/ { + #address-cells = <2>; + #size-cells = <2>; + model = "Broadcom STB (bcm7445)"; + compatible = "brcm,bcm7445", "brcm,brcmstb"; + +Further, syscon nodes that map platform-specific registers used for general +system control is required: + + - compatible: "brcm,bcm<chip_id>-sun-top-ctrl", "syscon" + - compatible: "brcm,bcm<chip_id>-cpu-biu-ctrl", + "brcm,brcmstb-cpu-biu-ctrl", + "syscon" + - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon" + +cpu-biu-ctrl node +------------------- +SoCs with Broadcom Brahma15 ARM-based and Brahma53 ARM64-based CPUs have a +specific Bus Interface Unit (BIU) block which controls and interfaces the CPU +complex to the different Memory Controller Ports (MCP), one per memory +controller (MEMC). This BIU block offers a feature called Write Pairing which +consists in collapsing two adjacent cache lines into a single (bursted) write +transaction towards the memory controller (MEMC) to maximize write bandwidth. + +Required properties: + + - compatible: must be "brcm,bcm7445-cpu-biu-ctrl", "brcm,brcmstb-cpu-biu-ctrl", "syscon" + +Optional properties: + + - brcm,write-pairing: + Boolean property, which when present indicates that the chip + supports write-pairing. + +example: + rdb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0x00 0xf0000000 0x1000000>; + + sun_top_ctrl: syscon@404000 { + compatible = "brcm,bcm7445-sun-top-ctrl", "syscon"; + reg = <0x404000 0x51c>; + }; + + hif_cpubiuctrl: syscon@3e2400 { + compatible = "brcm,bcm7445-cpu-biu-ctrl", "brcm,brcmstb-cpu-biu-ctrl", "syscon"; + reg = <0x3e2400 0x5b4>; + brcm,write-pairing; + }; + + hif_continuation: syscon@452000 { + compatible = "brcm,bcm7445-hif-continuation", "syscon"; + reg = <0x452000 0x100>; + }; + }; + +Nodes that allow for support of SMP initialization and reboot are required: + +smpboot +------- +Required properties: + + - compatible + The string "brcm,brcmstb-smpboot". + + - syscon-cpu + A phandle / integer array property which lets the BSP know the location + of certain CPU power-on registers. + + The layout of the property is as follows: + o a phandle to the "hif_cpubiuctrl" syscon node + o offset to the base CPU power zone register + o offset to the base CPU reset register + + - syscon-cont + A phandle pointing to the syscon node which describes the CPU boot + continuation registers. + o a phandle to the "hif_continuation" syscon node + +example: + smpboot { + compatible = "brcm,brcmstb-smpboot"; + syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>; + syscon-cont = <&hif_continuation>; + }; + +reboot +------- +Required properties + + - compatible + The string property "brcm,brcmstb-reboot" for 40nm/28nm chips with + the new SYS_CTRL interface, or "brcm,bcm7038-reboot" for 65nm + chips with the old SUN_TOP_CTRL interface. + + - syscon + A phandle / integer array that points to the syscon node which describes + the general system reset registers. + o a phandle to "sun_top_ctrl" + o offset to the "reset source enable" register + o offset to the "software master reset" register + +example: + reboot { + compatible = "brcm,brcmstb-reboot"; + syscon = <&sun_top_ctrl 0x304 0x308>; + }; + + + +Power management +---------------- + +For power management (particularly, S2/S3/S5 system suspend), the following SoC +components are needed: + += Always-On control block (AON CTRL) + +This hardware provides control registers for the "always-on" (even in low-power +modes) hardware, such as the Power Management State Machine (PMSM). + +Required properties: +- compatible : should contain "brcm,brcmstb-aon-ctrl" +- reg : the register start and length for the AON CTRL block + +Example: + +aon-ctrl@410000 { + compatible = "brcm,brcmstb-aon-ctrl"; + reg = <0x410000 0x400>; +}; + += Memory controllers + +A Broadcom STB SoC typically has a number of independent memory controllers, +each of which may have several associated hardware blocks, which are versioned +independently (control registers, DDR PHYs, etc.). One might consider +describing these controllers as a parent "memory controllers" block, which +contains N sub-nodes (one for each controller in the system), each of which is +associated with a number of hardware register resources (e.g., its PHY). See +the example device tree snippet below. + +== MEMC (MEMory Controller) + +Represents a single memory controller instance. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc" and "simple-bus" + +Should contain subnodes for any of the following relevant hardware resources: + +== DDR PHY control + +Control registers for this memory controller's DDR PHY. + +Required properties: +- compatible : should contain one of these + "brcm,brcmstb-ddr-phy-v71.1" + "brcm,brcmstb-ddr-phy-v72.0" + "brcm,brcmstb-ddr-phy-v225.1" + "brcm,brcmstb-ddr-phy-v240.1" + "brcm,brcmstb-ddr-phy-v240.2" + +- reg : the DDR PHY register range + +== DDR SHIMPHY + +Control registers for this memory controller's DDR SHIMPHY. + +Required properties: +- compatible : should contain "brcm,brcmstb-ddr-shimphy-v1.0" +- reg : the DDR SHIMPHY register range + +== MEMC DDR control + +Sequencer DRAM parameters and control registers. Used for Self-Refresh +Power-Down (SRPD), among other things. + +Required properties: +- compatible : should contain one of these + "brcm,brcmstb-memc-ddr-rev-b.2.1" + "brcm,brcmstb-memc-ddr-rev-b.2.2" + "brcm,brcmstb-memc-ddr-rev-b.2.3" + "brcm,brcmstb-memc-ddr-rev-b.3.0" + "brcm,brcmstb-memc-ddr-rev-b.3.1" + "brcm,brcmstb-memc-ddr" +- reg : the MEMC DDR register range + +Example: + +memory_controllers { + ranges; + compatible = "simple-bus"; + + memc@0 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1106000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1106000 0x21c>; + }; + + shimphy@f1108000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1108000 0xe4>; + }; + + memc-ddr@f1102000 { + reg = <0xf1102000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; + + memc@1 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1186000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1186000 0x21c>; + }; + + shimphy@f1188000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1188000 0xe4>; + }; + + memc-ddr@f1182000 { + reg = <0xf1182000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; + + memc@2 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1206000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1206000 0x21c>; + }; + + shimphy@f1208000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1208000 0xe4>; + }; + + memc-ddr@f1202000 { + reg = <0xf1202000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,cygnus.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,cygnus.txt new file mode 100644 index 000000000..4c77169bb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,cygnus.txt @@ -0,0 +1,31 @@ +Broadcom Cygnus device tree bindings +------------------------------------ + + +Boards with Cygnus SoCs shall have the following properties: + +Required root node property: + +BCM11300 +compatible = "brcm,bcm11300", "brcm,cygnus"; + +BCM11320 +compatible = "brcm,bcm11320", "brcm,cygnus"; + +BCM11350 +compatible = "brcm,bcm11350", "brcm,cygnus"; + +BCM11360 +compatible = "brcm,bcm11360", "brcm,cygnus"; + +BCM58300 +compatible = "brcm,bcm58300", "brcm,cygnus"; + +BCM58302 +compatible = "brcm,bcm58302", "brcm,cygnus"; + +BCM58303 +compatible = "brcm,bcm58303", "brcm,cygnus"; + +BCM58305 +compatible = "brcm,bcm58305", "brcm,cygnus"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt new file mode 100644 index 000000000..a124c7fc4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt @@ -0,0 +1,14 @@ +Broadcom Hurricane 2 device tree bindings +--------------------------------------- + +Broadcom Hurricane 2 family of SoCs are used for switching control. These SoCs +are based on Broadcom's iProc SoC architecture and feature a single core Cortex +A9 ARM CPUs, DDR2/DDR3 memory, PCIe GEN-2, USB 2.0 and USB 3.0, serial and NAND +flash and a PCIe attached integrated switching engine. + +Boards with Hurricane SoCs shall have the following properties: + +Required root node property: + +BCM53342 +compatible = "brcm,bcm53342", "brcm,hr2"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt new file mode 100644 index 000000000..35f056f4a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt @@ -0,0 +1,9 @@ +Broadcom North Star 2 (NS2) device tree bindings +------------------------------------------------ + +Boards with NS2 shall have the following properties: + +Required root node property: + +NS2 SVK board +compatible = "brcm,ns2-svk", "brcm,ns2"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt new file mode 100644 index 000000000..677ef9d9f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp-cpu-method.txt @@ -0,0 +1,39 @@ +Broadcom Northstar Plus SoC CPU Enable Method +--------------------------------------------- +This binding defines the enable method used for starting secondary +CPU in the following Broadcom SoCs: + BCM58522, BCM58525, BCM58535, BCM58622, BCM58623, BCM58625, BCM88312 + +The enable method is specified by defining the following required +properties in the corresponding secondary "cpu" device tree node: + - enable-method = "brcm,bcm-nsp-smp"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register which should hold the common +entry point for a secondary CPU. This entry is cpu node specific +and should be added per cpu. E.g., in case of NSP (BCM58625) which +is a dual core CPU SoC, this entry should be added to cpu1 node. + + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + enable-method = "brcm,bcm-nsp-smp"; + secondary-boot-reg = <0xffff042c>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt new file mode 100644 index 000000000..eae53e455 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt @@ -0,0 +1,34 @@ +Broadcom Northstar Plus device tree bindings +-------------------------------------------- + +Broadcom Northstar Plus family of SoCs are used for switching control +and management applications as well as residential router/gateway +applications. The SoC features dual core Cortex A9 ARM CPUs, integrating +several peripheral interfaces including multiple Gigabit Ethernet PHYs, +DDR3 memory, PCIE Gen-2, USB 2.0 and USB 3.0, serial and NAND flash, +SATA and several other IO controllers. + +Boards with Northstar Plus SoCs shall have the following properties: + +Required root node property: + +BCM58522 +compatible = "brcm,bcm58522", "brcm,nsp"; + +BCM58525 +compatible = "brcm,bcm58525", "brcm,nsp"; + +BCM58535 +compatible = "brcm,bcm58535", "brcm,nsp"; + +BCM58622 +compatible = "brcm,bcm58622", "brcm,nsp"; + +BCM58623 +compatible = "brcm,bcm58623", "brcm,nsp"; + +BCM58625 +compatible = "brcm,bcm58625", "brcm,nsp"; + +BCM88312 +compatible = "brcm,bcm88312", "brcm,nsp"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,stingray.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,stingray.txt new file mode 100644 index 000000000..23a02178d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,stingray.txt @@ -0,0 +1,12 @@ +Broadcom Stingray device tree bindings +------------------------------------------------ + +Boards with Stingray shall have the following properties: + +Required root node property: + +Stingray Combo SVK board +compatible = "brcm,bcm958742k", "brcm,stingray"; + +Stingray SST100 board +compatible = "brcm,bcm958742t", "brcm,stingray"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,vulcan-soc.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,vulcan-soc.txt new file mode 100644 index 000000000..223ed3471 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,vulcan-soc.txt @@ -0,0 +1,10 @@ +Broadcom Vulcan device tree bindings +------------------------------------ + +Boards with Broadcom Vulcan shall have the following root property: + +Broadcom Vulcan Evaluation Board: + compatible = "brcm,vulcan-eval", "brcm,vulcan-soc"; + +Generic Vulcan board: + compatible = "brcm,vulcan-soc"; diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.txt b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.txt new file mode 100644 index 000000000..6824b3180 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.txt @@ -0,0 +1,14 @@ +Raspberry Pi VideoCore firmware driver + +Required properties: + +- compatible: Should be "raspberrypi,bcm2835-firmware" +- mboxes: Phandle to the firmware device's Mailbox. + (See: ../mailbox/mailbox.txt for more information) + +Example: + +firmware { + compatible = "raspberrypi,bcm2835-firmware"; + mboxes = <&mailbox>; +}; |