1 files changed, 87 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
new file mode 100644
index 000000000..5d5bd456d
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -0,0 +1,87 @@
+* AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+It is possible, but not required, to represent each port as a sub-node.
+It allows to enable each port independently when dealing with multiple
+PHYs.
+
+Required properties:
+- compatible        : compatible string, one of:
+  - "allwinner,sun4i-a10-ahci"
+  - "brcm,iproc-ahci"
+  - "hisilicon,hisi-ahci"
+  - "cavium,octeon-7130-ahci"
+  - "ibm,476gtr-ahci"
+  - "marvell,armada-380-ahci"
+  - "marvell,armada-3700-ahci"
+  - "snps,dwc-ahci"
+  - "snps,spear-ahci"
+  - "generic-ahci"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- reg               : <registers mapping>
+
+Please note that when using "generic-ahci" you must also specify a SoC specific
+compatible:
+	compatible = "manufacturer,soc-model-ahci", "generic-ahci";
+
+Optional properties:
+- dma-coherent      : Present if dma operations are coherent
+- clocks            : a list of phandle + clock specifier pairs
+- resets            : a list of phandle + reset specifier pairs
+- target-supply     : regulator for SATA target power
+- phys              : reference to the SATA PHY node
+- phy-names         : must be "sata-phy"
+- ports-implemented : Mask that indicates which ports that the HBA supports
+		      are available for software to use. Useful if PORTS_IMPL
+		      is not programmed by the BIOS, which is true with
+		      some embedded SOC's.
+
+Required properties when using sub-nodes:
+- #address-cells    : number of cells to encode an address
+- #size-cells       : number of cells representing the size of an address
+
+
+Sub-nodes required properties:
+- reg		    : the port number
+And at least one of the following properties:
+- phys		    : reference to the SATA PHY node
+- target-supply    : regulator for SATA target power
+
+Examples:
+        sata@ffe08000 {
+		compatible = "snps,spear-ahci";
+		reg = <0xffe08000 0x1000>;
+		interrupts = <115>;
+        };
+
+	ahci: sata@1c18000 {
+		compatible = "allwinner,sun4i-a10-ahci";
+		reg = <0x01c18000 0x1000>;
+		interrupts = <56>;
+		clocks = <&pll6 0>, <&ahb_gates 25>;
+		target-supply = <&reg_ahci_5v>;
+	};
+
+With sub-nodes:
+	sata@f7e90000 {
+		compatible = "marvell,berlin2q-achi", "generic-ahci";
+		reg = <0xe90000 0x1000>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&chip CLKID_SATA>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sata0: sata-port@0 {
+			reg = <0>;
+			phys = <&sata_phy 0>;
+			target-supply = <&reg_sata0>;
+		};
+
+		sata1: sata-port@1 {
+			reg = <1>;
+			phys = <&sata_phy 1>;
+			target-supply = <&reg_sata1>;;
+		};
+	};