diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/frequency/adf4350.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/iio/frequency/adf4350.txt | 86 |
1 files changed, 86 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt new file mode 100644 index 000000000..f8c181d81 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt @@ -0,0 +1,86 @@ +Analog Devices ADF4350/ADF4351 device driver + +Required properties: + - compatible: Should be one of + * "adi,adf4350": When using the ADF4350 device + * "adi,adf4351": When using the ADF4351 device + - reg: SPI chip select numbert for the device + - spi-max-frequency: Max SPI frequency to use (< 20000000) + - clocks: From common clock binding. Clock is phandle to clock for + ADF435x Reference Clock (CLKIN). + +Optional properties: + - gpios: GPIO Lock detect - If set with a valid phandle and GPIO number, + pll lock state is tested upon read. + - adi,channel-spacing: Channel spacing in Hz (influences MODULUS). + - adi,power-up-frequency: If set in Hz the PLL tunes to + the desired frequency on probe. + - adi,reference-div-factor: If set the driver skips dynamic calculation + and uses this default value instead. + - adi,reference-doubler-enable: Enables reference doubler. + - adi,reference-div2-enable: Enables reference divider. + - adi,phase-detector-polarity-positive-enable: Enables positive phase + detector polarity. Default = negative. + - adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision. + Default = 10ns. + - adi,lock-detect-function-integer-n-enable: Enables lock detect + for integer-N mode. Default = factional-N mode. + - adi,charge-pump-current: Charge pump current in mA. + Default = 2500mA. + - adi,muxout-select: On chip multiplexer output selection. + Valid values for the multiplexer output are: + 0: Three-State Output (default) + 1: DVDD + 2: DGND + 3: R-Counter output + 4: N-Divider output + 5: Analog lock detect + 6: Digital lock detect + - adi,low-spur-mode-enable: Enables low spur mode. + Default = Low noise mode. + - adi,cycle-slip-reduction-enable: Enables cycle slip reduction. + - adi,charge-cancellation-enable: Enabled charge pump + charge cancellation for integer-N modes. + - adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width + for integer-N modes. + - adi,band-select-clock-mode-high-enable: Enables faster band + selection logic. + - adi,12bit-clk-divider: Clock divider value used when + adi,12bit-clkdiv-mode != 0 + - adi,clk-divider-mode: + Valid values for the clkdiv mode are: + 0: Clock divider off (default) + 1: Fast lock enable + 2: Phase resync enable + - adi,aux-output-enable: Enables auxiliary RF output. + - adi,aux-output-fundamental-enable: Selects fundamental VCO output on + the auxiliary RF output. Default = Output of RF dividers. + - adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function. + - adi,output-power: Output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + - adi,aux-output-power: Auxiliary output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + + +Example: + lo_pll0_rx_adf4351: adf4351-rx-lpc@4 { + compatible = "adi,adf4351"; + reg = <4>; + spi-max-frequency = <10000000>; + clocks = <&clk0_ad9523 9>; + clock-names = "clkin"; + adi,channel-spacing = <10000>; + adi,power-up-frequency = <2400000000>; + adi,phase-detector-polarity-positive-enable; + adi,charge-pump-current = <2500>; + adi,output-power = <3>; + adi,mute-till-lock-enable; + }; |