diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/light')
13 files changed, 321 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/light/apds9300.txt b/Documentation/devicetree/bindings/iio/light/apds9300.txt new file mode 100644 index 000000000..aa199e09a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/apds9300.txt @@ -0,0 +1,21 @@ +* Avago APDS9300 ambient light sensor + +http://www.avagotech.com/docs/AV02-1077EN + +Required properties: + + - compatible : should be "avago,apds9300" + - reg : the I2C address of the sensor + +Optional properties: + + - interrupts : interrupt mapping for GPIO IRQ + +Example: + +apds9300@39 { + compatible = "avago,apds9300"; + reg = <0x39>; + interrupt-parent = <&gpio2>; + interrupts = <29 8>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9960.txt b/Documentation/devicetree/bindings/iio/light/apds9960.txt new file mode 100644 index 000000000..3af325ad1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/apds9960.txt @@ -0,0 +1,21 @@ +* Avago APDS9960 gesture/RGB/ALS/proximity sensor + +http://www.avagotech.com/docs/AV02-4191EN + +Required properties: + + - compatible: must be "avago,apds9960" + - reg: the I2c address of the sensor + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +apds9960@39 { + compatible = "avago,apds9960"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/cm3605.txt b/Documentation/devicetree/bindings/iio/light/cm3605.txt new file mode 100644 index 000000000..56331a79f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/cm3605.txt @@ -0,0 +1,41 @@ +Capella Microsystems CM3605 +Ambient Light and Short Distance Proximity Sensor + +The CM3605 is an entirely analog part which however require quite a bit of +software logic to interface a host operating system. + +This ALS and proximity sensor was one of the very first deployed in mobile +handsets, notably it is used in the very first Nexus One Android phone from +2010. + +Required properties: +- compatible: must be: "capella,cm3605" +- aset-gpios: GPIO line controlling the ASET line (drive low + to activate the ALS, should be flagged GPIO_ACTIVE_LOW) +- interrupts: the IRQ line (such as a GPIO) that is connected to + the POUT (proximity sensor out) line. The edge detection must + be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward + and away from the proximity sensor. +- io-channels: the ADC channel used for converting the voltage from + AOUT to a digital representation. +- io-channel-names: must be "aout" + +Optional properties: +- vdd-supply: regulator supplying VDD power to the component. +- capella,aset-resistance-ohms: the sensitivity calibration resistance, + in Ohms. Valid values are: 50000, 100000, 300000 and 600000, + as these are the resistance values that we are supplied with + calibration curves for. If not supplied, 100 kOhm will be assumed + but it is strongly recommended to supply this. + +Example: + +cm3605 { + compatible = "capella,cm3605"; + vdd-supply = <&foo_reg>; + aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>; + capella,aset-resistance-ohms = <100000>; + interrupts = <1 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&adc 0x01>; + io-channel-names = "aout"; +}; diff --git a/Documentation/devicetree/bindings/iio/light/cm36651.txt b/Documentation/devicetree/bindings/iio/light/cm36651.txt new file mode 100644 index 000000000..c03e19db4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/cm36651.txt @@ -0,0 +1,26 @@ +* Capella CM36651 I2C Proximity and Color Light sensor + +Required properties: +- compatible: must be "capella,cm36651" +- reg: the I2C address of the device +- interrupts: interrupt-specifier for the sole interrupt + generated by the device +- vled-supply: regulator for the IR LED. IR_LED is a part + of the cm36651 for proximity detection. + As covered in ../../regulator/regulator.txt + +Example: + + i2c_cm36651: i2c-gpio { + /* ... */ + + cm36651@18 { + compatible = "capella,cm36651"; + reg = <0x18>; + interrupt-parent = <&gpx0>; + interrupts = <2 0>; + vled-supply = <&ps_als_reg>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt new file mode 100644 index 000000000..9231c8231 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt @@ -0,0 +1,21 @@ +* Sharp GP2AP020A00F I2C Proximity/ALS sensor + +The proximity detector sensor requires power supply +for its built-in led. It is also defined by this binding. + +Required properties: + + - compatible : should be "sharp,gp2ap020a00f" + - reg : the I2C slave address of the light sensor + - interrupts : interrupt specifier for the sole interrupt generated + by the device + - vled-supply : VLED power supply, as covered in ../regulator/regulator.txt + +Example: + +gp2ap020a00f@39 { + compatible = "sharp,gp2ap020a00f"; + reg = <0x39>; + interrupts = <2 0>; + vled-supply = <...>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.txt b/Documentation/devicetree/bindings/iio/light/isl29018.txt new file mode 100644 index 000000000..b9bbde3e1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/isl29018.txt @@ -0,0 +1,27 @@ +* ISL 29018/29023/29035 I2C ALS, Proximity, and Infrared sensor + +Required properties: + + - compatible: Should be one of + "isil,isl29018" + "isil,isl29023" + "isil,isl29035" + - reg: the I2C address of the device + +Optional properties: + + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +isl29018@44 { + compatible = "isil,isl29018"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/isl29501.txt b/Documentation/devicetree/bindings/iio/light/isl29501.txt new file mode 100644 index 000000000..46957997f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/isl29501.txt @@ -0,0 +1,13 @@ +* ISL29501 Time-of-flight sensor. + +Required properties: + + - compatible : should be "renesas,isl29501" + - reg : the I2C address of the sensor + +Example: + +isl29501@57 { + compatible = "renesas,isl29501"; + reg = <0x57>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/opt3001.txt b/Documentation/devicetree/bindings/iio/light/opt3001.txt new file mode 100644 index 000000000..47b13eb8f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/opt3001.txt @@ -0,0 +1,25 @@ +* Texas Instruments OPT3001 Ambient Light Sensor + +The driver supports interrupt-driven and interrupt-less operation, depending +on whether an interrupt property has been populated into the DT. Note that +the optional generation of IIO events on rising/falling light threshold changes +requires the use of interrupts. Without interrupts, only the simple reading +of the current light value is supported through the IIO API. + +http://www.ti.com/product/opt3001 + +Required properties: + - compatible: should be "ti,opt3001" + - reg: the I2C address of the sensor + +Optional properties: + - interrupts: interrupt mapping for GPIO IRQ (configure for falling edge) + +Example: + +opt3001@44 { + compatible = "ti,opt3001"; + reg = <0x44>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2563.txt b/Documentation/devicetree/bindings/iio/light/tsl2563.txt new file mode 100644 index 000000000..f91e809e7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2563.txt @@ -0,0 +1,19 @@ +* AMS TAOS TSL2563 ambient light sensor + +Required properties: + + - compatible : should be "amstaos,tsl2563" + - reg : the I2C address of the sensor + +Optional properties: + + - amstaos,cover-comp-gain : integer used as multiplier for gain + compensation (default = 1) + +Example: + +tsl2563@29 { + compatible = "amstaos,tsl2563"; + reg = <0x29>; + amstaos,cover-comp-gain = <16>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt new file mode 100644 index 000000000..059dffa18 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt @@ -0,0 +1,25 @@ +* TAOS TSL 2580/2581/2583 ALS sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2580" + "amstaos,tsl2581" + "amstaos,tsl2583" + - reg: the I2C address of the device + +Optional properties: + + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +tsl2581@29 { + compatible = "amstaos,tsl2581"; + reg = <0x29>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/us5182d.txt b/Documentation/devicetree/bindings/iio/light/us5182d.txt new file mode 100644 index 000000000..a61979997 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/us5182d.txt @@ -0,0 +1,45 @@ +* UPISEMI us5182d I2C ALS and Proximity sensor + +Required properties: +- compatible: must be "upisemi,usd5182" +- reg: the I2C address of the device + +Optional properties: +- upisemi,glass-coef: glass attenuation factor - compensation factor of + resolution 1000 for material transmittance. + +- upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc + counts) corresponding to every scale. + +- upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4 + fractional bits - Q4.4) applied when light > threshold + +- upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4 + fractional bits - Q4.4) applied when light < threshold + +- upisemi,continuous: This chip has two power modes: one-shot (chip takes one + measurement and then shuts itself down) and continuous ( + chip takes continuous measurements). The one-shot mode is + more power-friendly but the continuous mode may be more + reliable. If this property is specified the continuous + mode will be used instead of the default one-shot one for + raw reads. + +If the optional properties are not specified these factors will default to the +values in the below example. +The glass-coef defaults to no compensation for the covering material. +The threshold array defaults to experimental values that work with US5182D +sensor on evaluation board - roughly between 12-32 lux. +There will be no dark-gain compensation by default when ALS > thresh +(0 * dark-gain), and a 1.35 compensation factor when ALS < thresh. + +Example: + + usd5182@39 { + compatible = "upisemi,usd5182"; + reg = <0x39>; + upisemi,glass-coef = < 1000 >; + upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>; + upisemi,upper-dark-gain = /bits/ 8 <0x00>; + upisemi,lower-dark-gain = /bits/ 8 <0x16>; + }; diff --git a/Documentation/devicetree/bindings/iio/light/uvis25.txt b/Documentation/devicetree/bindings/iio/light/uvis25.txt new file mode 100644 index 000000000..043c139d9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/uvis25.txt @@ -0,0 +1,22 @@ +* ST UVIS25 uv sensor + +Required properties: +- compatible: should be "st,uvis25" +- reg: i2c address of the sensor / spi cs line + +Optional properties: +- interrupts: interrupt mapping for IRQ. It should be configured with + flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt + client node bindings. + +Example: + +uvis25@47 { + compatible = "st,uvis25"; + reg = <0x47>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/vl6180.txt b/Documentation/devicetree/bindings/iio/light/vl6180.txt new file mode 100644 index 000000000..2c5295271 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/vl6180.txt @@ -0,0 +1,15 @@ +STMicro VL6180 - ALS, range and proximity sensor + +Link to datasheet: http://www.st.com/resource/en/datasheet/vl6180x.pdf + +Required properties: + + -compatible: should be "st,vl6180" + -reg: the I2C address of the sensor + +Example: + +vl6180@29 { + compatible = "st,vl6180"; + reg = <0x29>; +}; |