diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input/touchscreen')
39 files changed, 1531 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt new file mode 100644 index 000000000..cdd743a1f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt @@ -0,0 +1,71 @@ +* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C) + +Required properties: +- compatible : for SPI slave, use "adi,ad7879" + for I2C slave, use "adi,ad7879-1" +- reg : SPI chipselect/I2C slave address + See spi-bus.txt for more SPI slave properties +- interrupts : touch controller interrupt +- touchscreen-max-pressure : maximum reported pressure +- adi,resistance-plate-x : total resistance of X-plate (for pressure + calculation) +Optional properties: +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) +- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us) + 13 : 2.560ms + 14 : 3.584ms + 15 : 4.096ms + This property has to be a '/bits/ 8' value +- adi,acquisition-time : 0: 2us + 1: 4us + 2: 8us + 3: 16us + This property has to be a '/bits/ 8' value +- adi,median-filter-size : 0: disabled + 1: 4 measurements + 2: 8 measurements + 3: 16 measurements + This property has to be a '/bits/ 8' value +- adi,averaging : 0: 2 middle values (1 if median disabled) + 1: 4 middle values + 2: 8 middle values + 3: 16 values + This property has to be a '/bits/ 8' value +- adi,conversion-interval: : 0 : convert one time only + 1-255: 515us + val * 35us (up to 9.440ms) + This property has to be a '/bits/ 8' value +- gpio-controller : Switch AUX/VBAT/GPIO pin to GPIO mode + +Example: + + ad7879@2c { + compatible = "adi,ad7879-1"; + reg = <0x2c>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; + + ad7879@1 { + compatible = "adi,ad7879"; + spi-max-frequency = <5000000>; + reg = <1>; + spi-cpol; + spi-cpha; + gpio-controller; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt new file mode 100644 index 000000000..04413da51 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt @@ -0,0 +1,93 @@ +Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046 +SPI driven touch screen controllers. + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Additional required properties: + + compatible Must be one of the following, depending on the + model: + "ti,tsc2046" + "ti,ads7843" + "ti,ads7845" + "ti,ads7846" + "ti,ads7873" + + interrupts An interrupt node describing the IRQ line the chip's + !PENIRQ pin is connected to. + vcc-supply A regulator node for the supply voltage. + + +Optional properties: + + ti,vref-delay-usecs vref supply delay in usecs, 0 for + external vref (u16). + ti,vref-mv The VREF voltage, in millivolts (u16). + Set to 0 to use internal references + (ADS7846). + ti,keep-vref-on set to keep vref on for differential + measurements as well + ti,swap-xy swap x and y axis + ti,settle-delay-usec Settling time of the analog signals; + a function of Vcc and the capacitance + on the X/Y drivers. If set to non-zero, + two samples are taken with settle_delay + us apart, and the second one is used. + ~150 uSec with 0.01uF caps (u16). + ti,penirq-recheck-delay-usecs If set to non-zero, after samples are + taken this delay is applied and penirq + is rechecked, to help avoid false + events. This value is affected by the + material used to build the touch layer + (u16). + ti,x-plate-ohms Resistance of the X-plate, + in Ohms (u16). + ti,y-plate-ohms Resistance of the Y-plate, + in Ohms (u16). + ti,x-min Minimum value on the X axis (u16). + ti,y-min Minimum value on the Y axis (u16). + ti,x-max Maximum value on the X axis (u16). + ti,y-max Minimum value on the Y axis (u16). + ti,pressure-min Minimum reported pressure value + (threshold) - u16. + ti,pressure-max Maximum reported pressure value (u16). + ti,debounce-max Max number of additional readings per + sample (u16). + ti,debounce-tol Tolerance used for filtering (u16). + ti,debounce-rep Additional consecutive good readings + required after the first two (u16). + ti,pendown-gpio-debounce Platform specific debounce time for the + pendown-gpio (u32). + pendown-gpio GPIO handle describing the pin the !PENIRQ + line is connected to. + wakeup-source use any event on touchscreen as wakeup event. + (Legacy property support: "linux,wakeup") + + +Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC:: + + spi_controller { + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + interrupt-parent = <&gpio1>; + interrupts = <8 0>; /* BOOT6 / GPIO 8 */ + spi-max-frequency = <1000000>; + pendown-gpio = <&gpio1 8 0>; + vcc-supply = <®_vcc3>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <40>; + ti,pressure-max = /bits/ 16 <255>; + + wakeup-source; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt b/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt new file mode 100644 index 000000000..82019bd60 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt @@ -0,0 +1,15 @@ +* Microchip AR1020 and AR1021 touchscreen interface (I2C) + +Required properties: +- compatible : "microchip,ar1021-i2c" +- reg : I2C slave address +- interrupts : touch controller interrupt + +Example: + + touchscreen@4d { + compatible = "microchip,ar1021-i2c"; + reg = <0x4d>; + interrupt-parent = <&gpio3>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt new file mode 100644 index 000000000..f40f21c64 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt @@ -0,0 +1,30 @@ +* AUO in-cell touchscreen controller using Pixcir sensors + +Required properties: +- compatible: must be "auo,auo_pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- gpios: gpios the chip is connected to + first one is the interrupt gpio and second one the reset gpio +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + auo_pixcir_ts@5c { + compatible = "auo,auo_pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + + gpios = <&gpf 2 0 2>, /* INT */ + <&gpf 5 1 0>; /* RST */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt new file mode 100644 index 000000000..f127a2117 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -0,0 +1,87 @@ +* Broadcom's IPROC Touchscreen Controller + +Required properties: +- compatible: must be "brcm,iproc-touchscreen" +- ts_syscon: handler of syscon node defining physical base + address of the controller and length of memory mapped region. + If this property is selected please make sure MFD_SYSCON config + is enabled in the defconfig file. +- clocks: The clock provided by the SOC to driver the tsc +- clock-names: name for the clock +- interrupts: The touchscreen controller's interrupt +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: Specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. + +Optional properties: +- scanning_period: Time between scans. Each step is 1024 us. Valid 1-256. +- debounce_timeout: Each step is 512 us. Valid 0-255 +- settling_timeout: The settling duration (in ms) is the amount of time + the tsc waits to allow the voltage to settle after + turning on the drivers in detection mode. + Valid values: 0-11 + 0 = 0.008 ms + 1 = 0.01 ms + 2 = 0.02 ms + 3 = 0.04 ms + 4 = 0.08 ms + 5 = 0.16 ms + 6 = 0.32 ms + 7 = 0.64 ms + 8 = 1.28 ms + 9 = 2.56 ms + 10 = 5.12 ms + 11 = 10.24 ms +- touch_timeout: The continuous number of scan periods in which touch is + not detected before the controller returns to idle state. + Valid values 0-255. +- average_data: Number of data samples which are averaged before a final + data point is placed into the FIFO + Valid values 0-7 + 0 = 1 sample + 1 = 2 samples + 2 = 4 samples + 3 = 8 samples + 4 = 16 samples + 5 = 32 samples + 6 = 64 samples + 7 = 128 samples +- fifo_threshold: Interrupt is generated whenever the number of fifo + entries exceeds this value + Valid values 0-31 +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) +- touchscreen-fuzz-x: horizontal noise value of the absolute input + device (in pixels) +- touchscreen-fuzz-y: vertical noise value of the absolute input + device (in pixels) +- touchscreen-inverted-x: X axis is inverted (boolean) +- touchscreen-inverted-y: Y axis is inverted (boolean) + +Example: An example of touchscreen node + + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + touchscreen: touchscreen@180a6000 { + compatible = "brcm,iproc-touchscreen"; + #address-cells = <1>; + #size-cells = <1>; + ts_syscon = <&ts_adc_syscon>; + clocks = <&adc_clk>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + + scanning_period = <5>; + debounce_timeout = <40>; + settling_timeout = <7>; + touch_timeout = <10>; + average_data = <5>; + fifo_threshold = <1>; + /* Touchscreen is rotated 180 degrees. */ + touchscreen-inverted-x; + touchscreen-inverted-y; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt new file mode 100644 index 000000000..56d835242 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -0,0 +1,28 @@ +* Rohm BU21013 Touch Screen + +Required properties: + - compatible : "rohm,bu21013_tp" + - reg : I2C device address + +Optional properties: + - touch-gpio : GPIO pin registering a touch event + - <supply_name>-supply : Phandle to a regulator supply + - rohm,touch-max-x : Maximum outward permitted limit in the X axis + - rohm,touch-max-y : Maximum outward permitted limit in the Y axis + - rohm,flip-x : Flip touch coordinates on the X axis + - rohm,flip-y : Flip touch coordinates on the Y axis + +Example: + + i2c@80110000 { + bu21013_tp@5c { + compatible = "rohm,bu21013_tp"; + reg = <0x5c>; + touch-gpio = <&gpio2 20 0x4>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + rohm,touch-max-x = <384>; + rohm,touch-max-y = <704>; + rohm,flip-y; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt new file mode 100644 index 000000000..8daa0e868 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt @@ -0,0 +1,35 @@ +* Rohm BU21029 Touch Screen Controller + +Required properties: + - compatible : must be "rohm,bu21029" + - reg : i2c device address of the chip (0x40 or 0x41) + - interrupt-parent : the phandle for the gpio controller + - interrupts : (gpio) interrupt to which the chip is connected + - rohm,x-plate-ohms : x-plate resistance in Ohm + +Optional properties: + - reset-gpios : gpio pin to reset the chip (active low) + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-max-pressure: maximum pressure value + - vdd-supply : power supply for the controller + +Example: + + &i2c1 { + /* ... */ + + bu21029: bu21029@40 { + compatible = "rohm,bu21029"; + reg = <0x40>; + interrupt-parent = <&gpio1>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; + rohm,x-plate-ohms = <600>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-max-pressure = <4095>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt b/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt new file mode 100644 index 000000000..38b0603f6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt @@ -0,0 +1,44 @@ +* ChipOne icn8318 I2C touchscreen controller + +Required properties: + - compatible : "chipone,icn8318" + - reg : I2C slave address of the chip (0x40) + - interrupts : interrupt specification for the icn8318 interrupt + - wake-gpios : GPIO specification for the WAKE input + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + +Optional properties: + - pinctrl-names : should be "default" + - pinctrl-0: : a phandle pointing to the pin settings for the + control gpios + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + +Example: + +i2c@00000000 { + /* ... */ + + chipone_icn8318@40 { + compatible = "chipone,icn8318"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */ + pinctrl-names = "default"; + pinctrl-0 = <&ts_wake_pin_p66>; + wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; + + /* ... */ +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt new file mode 100644 index 000000000..2e1490a8f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt @@ -0,0 +1,34 @@ +* Toradex Colibri VF50 Touchscreen driver + +Required Properties: +- compatible must be toradex,vf50-touchscreen +- io-channels: adc channels being used by the Colibri VF50 module +- xp-gpios: FET gate driver for input of X+ +- xm-gpios: FET gate driver for input of X- +- yp-gpios: FET gate driver for input of Y+ +- ym-gpios: FET gate driver for input of Y- +- interrupts: pen irq interrupt for touch detection +- pinctrl-names: "idle", "default", "gpios" +- pinctrl-0: pinctrl node for pen/touch detection state pinmux +- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux +- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers +- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values + +Example: + + touchctrl: vf50_touchctrl { + compatible = "toradex,vf50-touchscreen"; + io-channels = <&adc1 0>,<&adc0 0>, + <&adc0 1>,<&adc1 2>; + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "idle","default","gpios"; + pinctrl-0 = <&pinctrl_touchctrl_idle>; + pinctrl-1 = <&pinctrl_touchctrl_default>; + pinctrl-2 = <&pinctrl_touchctrl_gpios>; + vf50-ts-min-pressure = <200>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt new file mode 100644 index 000000000..6ee274aa8 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt @@ -0,0 +1,93 @@ +* Cypress cyttsp touchscreen controller + +Required properties: + - compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi" + - reg : Device I2C address or SPI chip select number + - spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi) + - interrupts : (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). + - bootloader-key : the 8-byte bootloader key that is required to switch + the chip from bootloader mode (default mode) to + application mode. + This property has to be specified as an array of 8 + '/bits/ 8' values. + +Optional properties: + - reset-gpios : the reset gpio the chip is connected to + (see GPIO binding[1] for more details). + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-fuzz-x : horizontal noise value of the absolute input device + (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input device + (in pixels) + - active-distance : the distance in pixels beyond which a touch must move + before movement is detected and reported by the device. + Valid values: 0-15. + - active-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in active mode. + Valid values: 0-255. + - lowpower-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in low-power mode. + Valid values: 0-2550 + - touch-timeout-ms : minimum time in ms spent in the active power state while no + touches are detected before entering low-power mode. + Valid values: 0-2550 + - use-handshake : enable register-based handshake (boolean). This should + only be used if the chip is configured to use 'blocking + communication with timeout' (in this case the device + generates an interrupt at the end of every + scanning/processing cycle). + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + cyttsp@a { + compatible = "cypress,cyttsp-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; + + &mcspi1 { + /* ... */ + cyttsp@0 { + compatible = "cypress,cyttsp-spi"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt new file mode 100644 index 000000000..da2dc5d6c --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -0,0 +1,63 @@ +FocalTech EDT-FT5x06 Polytouch driver +===================================== + +There are 3 variants of the chip for various touch panel sizes +FT5206GE1 2.8" .. 3.8" +FT5306DE4 4.3" .. 7" +FT5406EE8 7" .. 8.9" +FT5506EEG 7" .. 8.9" + +The software interface is identical for all those chips, so that +currently there is no need for the driver to distinguish between the +different chips. Nevertheless distinct compatible strings are used so +that a distinction can be added if necessary without changing the DT +bindings. + + +Required properties: + - compatible: "edt,edt-ft5206" + or: "edt,edt-ft5306" + or: "edt,edt-ft5406" + or: "edt,edt-ft5506" + or: "focaltech,ft6236" + + - reg: I2C slave address of the chip (0x38) + - interrupts: interrupt specification for the touchdetect + interrupt + +Optional properties: + - reset-gpios: GPIO specification for the RESET input + - wake-gpios: GPIO specification for the WAKE input + + - pinctrl-names: should be "default" + - pinctrl-0: a phandle pointing to the pin settings for the + control gpios + + - threshold: allows setting the "click"-threshold in the range + from 0 to 80. + + - gain: allows setting the sensitivity in the range from 0 to + 31. Note that lower values indicate higher + sensitivity. + + - offset: allows setting the edge compensation in the range from + 0 to 31. + - touchscreen-size-x : See touchscreen.txt + - touchscreen-size-y : See touchscreen.txt + - touchscreen-fuzz-x : See touchscreen.txt + - touchscreen-fuzz-y : See touchscreen.txt + - touchscreen-inverted-x : See touchscreen.txt + - touchscreen-inverted-y : See touchscreen.txt + - touchscreen-swapped-x-y : See touchscreen.txt + +Example: + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5406", "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&edt_ft5x06_pins>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/eeti.txt b/Documentation/devicetree/bindings/input/touchscreen/eeti.txt new file mode 100644 index 000000000..32b3712c9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/eeti.txt @@ -0,0 +1,30 @@ +Bindings for EETI touchscreen controller + +Required properties: +- compatible: should be "eeti,exc3000-i2c" +- reg: I2C address of the chip. Should be set to <0xa> +- interrupts: interrupt to which the chip is connected + +Optional properties: +- attn-gpios: A handle to a GPIO to check whether interrupt is still + latched. This is necessary for platforms that lack + support for level-triggered IRQs. + +The following optional properties described in touchscreen.txt are +also supported: + +- touchscreen-inverted-x +- touchscreen-inverted-y +- touchscreen-swapped-x-y + +Example: + +i2c-master { + touchscreen@a { + compatible = "eeti,exc3000-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio>; + interrupts = <123 IRQ_TYPE_EDGE_RISING>; + attn-gpios = <&gpio 123 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt new file mode 100644 index 000000000..92fb2620f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt @@ -0,0 +1,18 @@ +* EETI eGalax Multiple Touch Controller + +Required properties: +- compatible: must be "eeti,egalax_ts" +- reg: i2c slave address +- interrupts: touch controller interrupt +- wakeup-gpios: the gpio pin to be used for waking up the controller + and also used as irq pin + +Example: + + touchscreen@4 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 2>; + wakeup-gpios = <&gpio1 9 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt new file mode 100644 index 000000000..94c4fc644 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt @@ -0,0 +1,25 @@ +* Elan eKTF2127 I2C touchscreen controller + +Required properties: + - compatible : "elan,ektf2127" + - reg : I2C slave address of the chip (0x40) + - interrupts : interrupt specification for the ektf2127 interrupt + - power-gpios : GPIO specification for the pin connected to the + ektf2127's wake input. This needs to be driven high + to take ektf2127 out of it's low power state + +For additional optional properties see: touchscreen.txt + +Example: + +i2c@00000000 { + ektf2127: touchscreen@15 { + compatible = "elan,ektf2127"; + reg = <0x15>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt new file mode 100644 index 000000000..68291b94f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt @@ -0,0 +1,26 @@ +* EETI EXC3000 Multiple Touch Controller + +Required properties: +- compatible: must be "eeti,exc3000" +- reg: i2c slave address +- interrupts: touch controller interrupt +- touchscreen-size-x: See touchscreen.txt +- touchscreen-size-y: See touchscreen.txt + +Optional properties: +- touchscreen-inverted-x: See touchscreen.txt +- touchscreen-inverted-y: See touchscreen.txt +- touchscreen-swapped-x-y: See touchscreen.txt + +Example: + + touchscreen@2a { + compatible = "eeti,exc3000"; + reg = <0x2a>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt new file mode 100644 index 000000000..99d6f9d25 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt @@ -0,0 +1,34 @@ +Freescale mx25 TS conversion queue module + +mx25 touchscreen conversion queue module which controls the ADC unit of the +mx25 for attached touchscreens. + +Required properties: + - compatible: Should be "fsl,imx25-tcq". + - reg: Memory range of the device. + - interrupts: Should be the interrupt number associated with this module within + the tscadc unit (<0>). + - fsl,wires: Should be '<4>' or '<5>' + +Optional properties: + - fsl,pen-debounce-ns: Pen debounce time in nanoseconds. + - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value + between 1 and 4096. It is the ratio between the internal reference voltage + and the measured voltage after the plate was precharged. Resistance between + plates and therefore the voltage decreases with pressure so that a smaller + value is equivalent to a higher pressure. + - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before + the actual touch detection to wait for an even charge distribution in the + plate. + +This device includes two conversion queues which can be added as subnodes. +The first queue is for the touchscreen, the second for general purpose ADC. + +Example: + tsc: tcq@50030400 { + compatible = "fsl,imx25-tcq"; + reg = <0x50030400 0x60>; + interrupt-parent = <&tscadc>; + interrupts = <0>; + fsl,wires = <4>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt new file mode 100644 index 000000000..f7e95c52f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt @@ -0,0 +1,43 @@ +Device tree bindings for Goodix GT9xx series touchscreen controller + +Required properties: + + - compatible : Should be "goodix,gt1151" + or "goodix,gt911" + or "goodix,gt9110" + or "goodix,gt912" + or "goodix,gt927" + or "goodix,gt9271" + or "goodix,gt928" + or "goodix,gt967" + - reg : I2C address of the chip. Should be 0x5d or 0x14 + - interrupts : Interrupt to which the chip is connected + +Optional properties: + + - irq-gpios : GPIO pin used for IRQ. The driver uses the + interrupt gpio pin as output to reset the device. + - reset-gpios : GPIO pin used for reset + + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + (swapping is done after inverting the axis) + +Example: + + i2c@00000000 { + /* ... */ + + gt928@5d { + compatible = "goodix,gt928"; + reg = <0x5d>; + interrupt-parent = <&gpio>; + interrupts = <0 0>; + + irq-gpios = <&gpio1 0 0>; + reset-gpios = <&gpio1 1 0>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt new file mode 100644 index 000000000..a47c36190 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt @@ -0,0 +1,41 @@ +* HiDeep Finger and Stylus touchscreen controller + +Required properties: +- compatible : must be "hideep,hideep-ts" +- reg : I2C slave address, (e.g. 0x6C). +- interrupts : Interrupt to which the chip is connected. + +Optional properties: +- vdd-supply : It is the controller supply for controlling + main voltage(3.3V) through the regulator. +- vid-supply : It is the controller supply for controlling + IO voltage(1.8V) through the regulator. +- reset-gpios : Define for reset gpio pin. + It is to use for reset IC. +- touchscreen-size-x : X axis size of touchscreen +- touchscreen-size-y : Y axis size of touchscreen +- linux,keycodes : Specifies an array of numeric keycode values to + be used for reporting button presses. The array can + contain up to 3 entries. + +Example: + +#include "dt-bindings/input/input.h" + +i2c@00000000 { + + /* ... */ + + touchscreen@6c { + compatible = "hideep,hideep-ts"; + reg = <0x6c>; + interrupt-parent = <&gpx1>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&ldo15_reg>; + vid-supply = <&ldo18_reg>; + reset-gpios = <&gpx1 5 0>; + touchscreen-size-x = <1080>; + touchscreen-size-y = <1920>; + linux,keycodes = <KEY_HOME>, <KEY_MENU>, <KEY_BACK>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt new file mode 100644 index 000000000..164915004 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt @@ -0,0 +1,38 @@ +* Freescale i.MX6UL Touch Controller + +Required properties: +- compatible: must be "fsl,imx6ul-tsc". +- reg: this touch controller address and the ADC2 address. +- interrupts: the interrupt of this touch controller and ADC2. +- clocks: the root clock of touch controller and ADC2. +- clock-names; must be "tsc" and "adc". +- xnur-gpio: the X- gpio this controller connect to. + This xnur-gpio returns to low once the finger leave the touch screen (The + last touch event the touch controller capture). + +Optional properties: +- measure-delay-time: the value of measure delay time. + Before X-axis or Y-axis measurement, the screen need some time before + even potential distribution ready. + This value depends on the touch screen. +- pre-charge-time: the touch screen need some time to precharge. + This value depends on the touch screen. +- touchscreen-average-samples: Number of data samples which are averaged for + each read. Valid values are 1, 4, 8, 16 and 32. + +Example: + tsc: tsc@2040000 { + compatible = "fsl,imx6ul-tsc"; + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6UL_CLK_IPG>, + <&clks IMX6UL_CLK_ADC2>; + clock-names = "tsc", "adc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xfff>; + pre-charge-time = <0xffff>; + touchscreen-average-samples = <32>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt new file mode 100644 index 000000000..41cbf4b7a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt @@ -0,0 +1,16 @@ +* NXP LPC32xx SoC Touchscreen Controller (TSC) + +Required properties: +- compatible: must be "nxp,lpc3220-tsc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The TSC/ADC interrupt + +Example: + + tsc@40048000 { + compatible = "nxp,lpc3220-tsc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt new file mode 100644 index 000000000..05e982c34 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt @@ -0,0 +1,17 @@ +* MAXI MAX11801 Resistive touch screen controller with i2c interface + +Required properties: +- compatible: must be "maxim,max11801" +- reg: i2c slave address +- interrupts: touch controller interrupt + +Example: + +&i2c1 { + max11801: touchscreen@48 { + compatible = "maxim,max11801"; + reg = <0x48>; + interrupt-parent = <&gpio3>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt new file mode 100644 index 000000000..b2ab5498e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt @@ -0,0 +1,20 @@ +* MELFAS MIP4 Touchscreen + +Required properties: +- compatible: must be "melfas,mip4_ts" +- reg: I2C slave address of the chip (0x48 or 0x34) +- interrupts: interrupt to which the chip is connected + +Optional properties: +- ce-gpios: GPIO connected to the CE (chip enable) pin of the chip + +Example: + i2c@00000000 { + touchscreen: melfas_mip4@48 { + compatible = "melfas,mip4_ts"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + ce-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt new file mode 100644 index 000000000..2cd954051 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt @@ -0,0 +1,41 @@ +* MELFAS MMS114/MMS152 touchscreen controller + +Required properties: +- compatible: should be one of: + - "melfas,mms114" + - "melfas,mms152" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- touchscreen-size-x: See [1] +- touchscreen-size-y: See [1] + +Optional properties: +- touchscreen-fuzz-x: See [1] +- touchscreen-fuzz-y: See [1] +- touchscreen-fuzz-pressure: See [1] +- touchscreen-inverted-x: See [1] +- touchscreen-inverted-y: See [1] +- touchscreen-swapped-x-y: See [1] + +[1]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupts = <39 0>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; + touchscreen-fuzz-x = <10>; + touchscreen-fuzz-y = <10>; + touchscreen-fuzz-pressure = <10>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file mode 100644 index 000000000..697a3e783 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -0,0 +1,31 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) + +Optional properties: +- reset-gpios: GPIO connected to the RESET line of the chip +- enable-gpios: GPIO connected to the ENABLE line of the chip +- wake-gpios: GPIO connected to the WAKE line of the chip + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + touchscreen-size-x = <800>; + touchscreen-size-y = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.txt b/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.txt new file mode 100644 index 000000000..51456c0e9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.txt @@ -0,0 +1,30 @@ +Generic resistive touchscreen ADC + +Required properties: + + - compatible: must be "resistive-adc-touch" +The device must be connected to an ADC device that provides channels for +position measurement and optional pressure. +Refer to ../iio/iio-bindings.txt for details + - iio-channels: must have at least two channels connected to an ADC device. +These should correspond to the channels exposed by the ADC device and should +have the right index as the ADC device registers them. These channels +represent the relative position on the "x" and "y" axes. + - iio-channel-names: must have all the channels' names. Mandatory channels +are "x" and "y". + +Optional properties: + - iio-channels: The third channel named "pressure" is optional and can be +used if the ADC device also measures pressure besides position. +If this channel is missing, pressure will be ignored and the touchscreen +will only report position. + - iio-channel-names: optional channel named "pressure". + +Example: + + resistive_touch: resistive_touch { + compatible = "resistive-adc-touch"; + touchscreen-min-pressure = <50000>; + io-channels = <&adc 24>, <&adc 25>, <&adc 26>; + io-channel-names = "x", "y", "pressure"; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt new file mode 100644 index 000000000..6805d10d2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt @@ -0,0 +1,32 @@ +* Samsung S6SY761 touchscreen controller + +Required properties: +- compatible : must be "samsung,s6sy761" +- reg : I2C slave address, (e.g. 0x48) +- interrupts : interrupt specification +- avdd-supply : analogic power supply +- vdd-supply : power supply + +Optional properties: +- touchscreen-size-x : see touchscreen.txt. This property is embedded in the + device. If defined it forces a different x resolution. +- touchscreen-size-y : see touchscreen.txt. This property is embedded in the + device. If defined it forces a different y resolution. + +Example: + +i2c@00000000 { + + /* ... */ + + touchscreen@48 { + compatible = "samsung,s6sy761"; + reg = <0x48>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_NONE>; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt new file mode 100644 index 000000000..d67e558e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -0,0 +1,44 @@ +* GSL 1680 touchscreen controller + +Required properties: +- compatible : Must be one of the following, depending on the model: + "silead,gsl1680" + "silead,gsl1688" + "silead,gsl3670" + "silead,gsl3675" + "silead,gsl3692" +- reg : I2C slave address of the chip (0x40) +- interrupts : interrupt specification for the gsl1680 interrupt +- power-gpios : Specification for the pin connected to the gsl1680's + shutdown input. This needs to be driven high to take the + gsl1680 out of its low power state +- touchscreen-size-x : See touchscreen.txt +- touchscreen-size-y : See touchscreen.txt + +Optional properties: +- firmware-name : File basename (string) for board specific firmware +- touchscreen-inverted-x : See touchscreen.txt +- touchscreen-inverted-y : See touchscreen.txt +- touchscreen-swapped-x-y : See touchscreen.txt +- silead,max-fingers : maximum number of fingers the touchscreen can detect +- silead,home-button : Boolean, set to true on devices which have a + capacitive home-button build into the touchscreen +- vddio-supply : regulator phandle for controller VDDIO +- avdd-supply : regulator phandle for controller AVDD + +Example: + +i2c@00000000 { + gsl1680: touchscreen@40 { + compatible = "silead,gsl1680"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + silead,max-fingers = <5>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt new file mode 100644 index 000000000..8f5322e01 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt @@ -0,0 +1,31 @@ +* SiS I2C Multiple Touch Controller + +Required properties: +- compatible: must be "sis,9200-ts" +- reg: i2c slave address +- interrupts: touch controller interrupt (see interrupt + binding [0]) + +Optional properties: +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the + device (see pinctrl binding [1]). +- attn-gpios: the gpio pin used as attention line +- reset-gpios: the gpio pin used to reset the controller +- wakeup-source: touchscreen can be used as a wakeup source + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + + sis9255@5c { + compatible = "sis,9200-ts"; + reg = <0x5c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sis>; + interrupt-parent = <&gpio3>; + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; + irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt new file mode 100644 index 000000000..64ad48b82 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt @@ -0,0 +1,24 @@ +* Sitronix st1232 touchscreen controller + +Required properties: +- compatible: must be "sitronix,st1232" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected + +Optional properties: +- gpios: a phandle to the reset GPIO + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@55 { + compatible = "sitronix,st1232"; + reg = <0x55>; + interrupts = <2 0>; + gpios = <&gpio1 166 0>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt b/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt new file mode 100644 index 000000000..0a5d0cb4a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt @@ -0,0 +1,41 @@ +* ST-Microelectronics FingerTip touchscreen controller + +The ST-Microelectronics FingerTip device provides a basic touchscreen +functionality. Along with it the user can enable the touchkey which can work as +a basic HOME and BACK key for phones. + +The driver supports also hovering as an absolute single touch event with x, y, z +coordinates. + +Required properties: +- compatible : must be "st,stmfts" +- reg : I2C slave address, (e.g. 0x49) +- interrupts : interrupt specification +- avdd-supply : analogic power supply +- vdd-supply : power supply +- touchscreen-size-x : see touchscreen.txt +- touchscreen-size-y : see touchscreen.txt + +Optional properties: +- touch-key-connected : specifies whether the touchkey feature is connected +- ledvdd-supply : power supply to the touch key leds + +Example: + +i2c@00000000 { + + /* ... */ + + touchscreen@49 { + compatible = "st,stmfts"; + reg = <0x49>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_NONE>; + touchscreen-size-x = <1599>; + touchscreen-size-y = <2559>; + touch-key-connected; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + ledvdd-supply = <&ldo33_reg>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt new file mode 100644 index 000000000..127baa31a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -0,0 +1,43 @@ +STMPE Touchscreen +---------------- + +Required properties: + - compatible: "st,stmpe-ts" + +Optional properties: +- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> + 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 + -> 144 clocks), recommended is 4. +- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) +- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external + reference) +- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) +- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 + samples, 3 -> 8 samples) +- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> + 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended + is 3 +- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 + -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 +- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of + the fractional part) recommended is 7 +- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 + mA max, 1 -> 50 mA typical 80 mA max) + +Node name must be stmpe_touchscreen and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt new file mode 100644 index 000000000..4886c4aa2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt @@ -0,0 +1,15 @@ +* Semtech SX8654 I2C Touchscreen Controller + +Required properties: +- compatible: must be "semtech,sx8654" +- reg: i2c slave address +- interrupts: touch controller interrupt + +Example: + + sx8654@48 { + compatible = "semtech,sx8654"; + reg = <0x48>; + interrupt-parent = <&gpio6>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt new file mode 100644 index 000000000..b1163bf97 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -0,0 +1,83 @@ +* TI - TSC ADC (Touschscreen and analog digital converter) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: +- child "tsc" + ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen + support on the platform. + ti,x-plate-resistance: X plate resistance + ti,coordinate-readouts: The sequencer supports a total of 16 + programmable steps each step is used to + read a single coordinate. A single + readout is enough but multiple reads can + increase the quality. + A value of 5 means, 5 reads for X, 5 for + Y and 2 for Z (always). This utilises 12 + of the 16 software steps available. The + remaining 4 can be used by the ADC. + ti,wire-config: Different boards could have a different order for + connecting wires on touchscreen. We need to provide an + 8 bit number where in the 1st four bits represent the + analog lines and the next 4 bits represent positive/ + negative terminal on that input line. Notations to + represent the input lines and terminals resoectively + is as follows: + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + XP = 0, XN = 1, YP = 2, YN = 3. +- child "adc" + ti,adc-channels: List of analog inputs available for ADC. + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + +Optional properties: +- child "tsc" + ti,charge-delay: Length of touch screen charge delay step in terms of + ADC clock cycles. Charge delay value should be large + in order to avoid false pen-up events. This value + effects the overall sampling speed, hence need to be + kept as low as possible, while avoiding false pen-up + event. Start from a lower value, say 0x400, and + increase value until false pen-up events are avoided. + The pen-up detection happens immediately after the + charge step, so this does in fact function as a + hardware knob for adjusting the amount of "settling + time". + +- child "adc" + ti,chan-step-opendelay: List of open delays for each channel of + ADC in the order of ti,adc-channels. The + value corresponds to the number of ADC + clock cycles to wait after applying the + step configuration registers and before + sending the start of ADC conversion. + Maximum value is 0x3FFFF. + ti,chan-step-sampledelay: List of sample delays for each channel + of ADC in the order of ti,adc-channels. + The value corresponds to the number of + ADC clock cycles to sample (to hold + start of conversion high). + Maximum value is 0xFF. + ti,chan-step-avg: Number of averages to be performed for each + channel of ADC. If average is 16 then input + is sampled 16 times and averaged to get more + accurate value. This increases the time taken + by ADC to generate a sample. Valid range is 0 + average to 16 averages. Maximum value is 16. + +Example: + tscadc: tscadc@44e0d000 { + compatible = "ti,am3359-tscadc"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordiante-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + ti,charge-delay = <0x400>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + ti,chan-step-opendelay = <0x098 0x3ffff 0x098 0x0>; + ti,chan-step-sampledelay = <0xff 0x0 0xf 0x0>; + ti,chan-step-avg = <16 2 4 8>; + }; + } diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt new file mode 100644 index 000000000..d092d5d03 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -0,0 +1,37 @@ +General Touchscreen Properties: + +Optional properties for Touchscreens: + - touchscreen-size-x : horizontal resolution of touchscreen + (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen + (in pixels) + - touchscreen-max-pressure : maximum reported pressure (arbitrary range + dependent on the controller) + - touchscreen-min-pressure : minimum pressure on the touchscreen to be + achieved in order for the touchscreen + driver to report a touch event. + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-pressure : pressure noise value of the absolute input + device (arbitrary range dependent on the + controller) + - touchscreen-average-samples : Number of data samples which are averaged + for each read (valid values dependent on the + controller) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + - touchscreen-x-mm : horizontal length in mm of the touchscreen + - touchscreen-y-mm : vertical length in mm of the touchscreen + +Deprecated properties for Touchscreens: + - x-size : deprecated name for touchscreen-size-x + - y-size : deprecated name for touchscreen-size-y + - moving-threshold : deprecated name for a combination of + touchscreen-fuzz-x and touchscreen-fuzz-y + - contact-threshold : deprecated name for touchscreen-fuzz-pressure + - x-invert : deprecated name for touchscreen-inverted-x + - y-invert : deprecated name for touchscreen-inverted-y diff --git a/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt new file mode 100644 index 000000000..4c1c092c2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt @@ -0,0 +1,11 @@ +* TS-4800 Touchscreen bindings + +Required properties: +- compatible: must be "technologic,ts4800-ts" +- reg: physical base address of the controller and length of memory mapped + region. +- syscon: phandle / integers array that points to the syscon node which + describes the FPGA's syscon registers. + - phandle to FPGA's syscon + - offset to the touchscreen register + - offset to the touchscreen enable bit diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt new file mode 100644 index 000000000..b80c04b0e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt @@ -0,0 +1,64 @@ +* Texas Instruments tsc2004 and tsc2005 touchscreen controllers + +Required properties: + - compatible : "ti,tsc2004" or "ti,tsc2005" + - reg : Device address + - interrupts : IRQ specifier + - spi-max-frequency : Maximum SPI clocking speed of the device + (for tsc2005) + +Optional properties: + - vio-supply : Regulator specifier + - reset-gpios : GPIO specifier for the controller reset line + - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates + in ohm (defaults to 280) + - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after + the configured time (in milli seconds), the driver + will reset it. This is disabled by default. + - properties defined in touchscreen.txt + +Example: + +&i2c3 { + tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; + interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>; + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +} + +&mcspi1 { + tsc2005@0 { + compatible = "ti,tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ + interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +} diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt new file mode 100644 index 000000000..ed00f61b8 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt @@ -0,0 +1,39 @@ +* Texas Instruments tsc2007 touchscreen controller + +Required properties: +- compatible: must be "ti,tsc2007". +- reg: I2C address of the chip. +- ti,x-plate-ohms: X-plate resistance in ohms. + +Optional properties: +- gpios: the interrupt gpio the chip is connected to (trough the penirq pin). + The penirq pin goes to low when the panel is touched. + (see GPIO binding[1] for more details). +- interrupts: (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). +- ti,max-rt: maximum pressure. +- ti,fuzzx: specifies the absolute input fuzz x value. + If set, it will permit noise in the data up to +- the value given to the fuzz + parameter, that is used to filter noise from the event stream. +- ti,fuzzy: specifies the absolute input fuzz y value. +- ti,fuzzz: specifies the absolute input fuzz z value. +- ti,poll-period: how much time to wait (in milliseconds) before reading again the + values from the tsc2007. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + tsc2007@49 { + compatible = "ti,tsc2007"; + reg = <0x49>; + interrupt-parent = <&gpio4>; + interrupts = <0x0 0x8>; + gpios = <&gpio4 0 0>; + ti,x-plate-ohms = <180>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt new file mode 100644 index 000000000..27d55a506 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt @@ -0,0 +1,30 @@ +Zeitec ZET6223 I2C touchscreen controller + +Required properties: +- compatible : "zeitec,zet6223" +- reg : I2C slave address of the chip (0x76) +- interrupts : interrupt specification for the zet6223 interrupt + +Optional properties: + +- vio-supply : Specification for VIO supply (1.8V or 3.3V, + depending on system interface needs). +- vcc-supply : Specification for 3.3V VCC supply. +- touchscreen-size-x : See touchscreen.txt +- touchscreen-size-y : See touchscreen.txt +- touchscreen-inverted-x : See touchscreen.txt +- touchscreen-inverted-y : See touchscreen.txt +- touchscreen-swapped-x-y : See touchscreen.txt + +Example: + +i2c@00000000 { + + zet6223: touchscreen@76 { + compatible = "zeitec,zet6223"; + reg = <0x76>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + }; + +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt new file mode 100644 index 000000000..e3c27c4fd --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -0,0 +1,34 @@ +* Neonode infrared touchscreen controller + +Required properties: +- compatible: must be "neonode,zforce" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- reset-gpios: reset gpio the chip is connected to +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- irq-gpios : interrupt gpio the chip is connected to +- vdd-supply: Regulator controlling the controller supply + +Example: + + i2c@00000000 { + /* ... */ + + zforce_ts@50 { + compatible = "neonode,zforce"; + reg = <0x50>; + interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; + + reset-gpios = <&gpio5 9 0>; /* RST */ + irq-gpios = <&gpio5 6 0>; /* IRQ, optional */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; |