diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power/supply')
43 files changed, 1556 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt new file mode 100644 index 000000000..f181e46d8 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt @@ -0,0 +1,16 @@ +=== AB8500 Battery Temperature Monitor Driver === + +The properties below describes the node for btemp driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-btemp" +- battery = Shall be battery specific information + + Example: + ab8500_btemp { + compatible = "stericsson,ab8500-btemp"; + battery = <&ab8500_battery>; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt new file mode 100644 index 000000000..56636f927 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt @@ -0,0 +1,16 @@ +=== AB8500 Charging Algorithm Driver === + +The properties below describes the node for chargalg driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-chargalg" +- battery = Shall be battery specific information + +Example: +ab8500_chargalg { + compatible = "stericsson,ab8500-chargalg"; + battery = <&ab8500_battery>; +}; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt new file mode 100644 index 000000000..24ada03e0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt @@ -0,0 +1,25 @@ +=== AB8500 Charger Driver === + +Required Properties: +- compatible = Shall be "stericsson,ab8500-charger" +- battery = Shall be battery specific information + Example: + ab8500_charger { + compatible = "stericsson,ab8500-charger"; + battery = <&ab8500_battery>; + }; + +- vddadc-supply: Supply for USB and Main charger + Example: + ab8500-charger { + vddadc-supply = <&ab8500_ldo_tvout_reg>; + } +- autopower_cfg: + Boolean value depicting the presence of 'automatic poweron after powerloss' + Example: + ab8500-charger { + autopower_cfg; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt new file mode 100644 index 000000000..ccafcb911 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt @@ -0,0 +1,58 @@ +=== AB8500 Fuel Gauge Driver === + +AB8500 is a mixed signal multimedia and power management +device comprising: power and energy-management-module, +wall-charger, usb-charger, audio codec, general purpose adc, +tvout, clock management and sim card interface. + +Fuelgauge support is part of energy-management-modules, other +components of this module are: +main-charger, usb-combo-charger and battery-temperature-monitoring. + +The properties below describes the node for fuelgauge driver. + +Required Properties: +- compatible = This shall be: "stericsson,ab8500-fg" +- battery = Shall be battery specific information + Example: + ab8500_fg { + compatible = "stericsson,ab8500-fg"; + battery = <&ab8500_battery>; + }; + +dependent node: + ab8500_battery: ab8500_battery { + }; + This node will provide information on 'thermistor interface' and + 'battery technology type' used. + +Properties of this node are: +thermistor-on-batctrl: + A boolean value indicating thermistor interface to battery + + Note: + 'btemp' and 'batctrl' are the pins interfaced for battery temperature + measurement, 'btemp' signal is used when NTC(negative temperature + coefficient) resister is interfaced external to battery whereas + 'batctrl' pin is used when NTC resister is internal to battery. + + Example: + ab8500_battery: ab8500_battery { + thermistor-on-batctrl; + }; + indicates: NTC resister is internal to battery, 'batctrl' is used + for thermal measurement. + + The absence of property 'thermal-on-batctrl' indicates + NTC resister is external to battery and 'btemp' signal is used + for thermal measurement. + +battery-type: + This shall be the battery manufacturing technology type, + allowed types are: + "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn" + Example: + ab8500_battery: ab8500_battery { + stericsson,battery-type = "LIPO"; + } + diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt new file mode 100644 index 000000000..c7dfb7cec --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt @@ -0,0 +1,44 @@ +Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a-charger". + - active-semi,chglev-gpios: charge current level phandle with args + as described in ../gpio/gpio.txt. + - active-semi,lbo-gpios: specify the low battery voltage detect phandle + with args as as described in ../gpio/gpio.txt. + - interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. + +Optional properties: + - active-semi,input-voltage-threshold-microvolt: unit: mV; + Specifies the charger's input over-voltage threshold value; + The value can be: 6600, 7000, 7500, 8000; default: 6600 + - active-semi,precondition-timeout: unit: minutes; + Specifies the charger's PRECONDITION safety timer setting value; + The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; + default: 40. + - active-semi,total-timeout: unit: hours; + Specifies the charger's total safety timer setting value; + The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; + default: 3. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt new file mode 100644 index 000000000..826e8a879 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt @@ -0,0 +1,22 @@ +AXP20X and AXP22X PMICs' AC power supply + +Required Properties: + - compatible: One of: + "x-powers,axp202-ac-power-supply" + "x-powers,axp221-ac-power-supply" + +This node is a subnode of the axp20x PMIC. + +The AXP20X can read the current current and voltage supplied by AC by +reading ADC channels from the AXP20X ADC. + +The AXP22X is only able to tell if an AC power supply is present and +usable. + +Example: + +&axp209 { + ac_power_supply: ac-power-supply { + compatible = "x-powers,axp202-ac-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt new file mode 100644 index 000000000..41916f699 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt @@ -0,0 +1,20 @@ +AXP20x and AXP22x battery power supply + +Required Properties: + - compatible, one of: + "x-powers,axp209-battery-power-supply" + "x-powers,axp221-battery-power-supply" + "x-powers,axp813-battery-power-supply" + +This node is a subnode of its respective PMIC DT node. + +The supported devices can read the battery voltage, charge and discharge +currents of the battery by reading ADC channels from the ADC. + +Example: + +&axp209 { + battery_power_supply: battery-power-supply { + compatible = "x-powers,axp209-battery-power-supply"; + } +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt new file mode 100644 index 000000000..ba8d35f66 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt @@ -0,0 +1,40 @@ +AXP20x USB power supply + +Required Properties: +-compatible: One of: "x-powers,axp202-usb-power-supply" + "x-powers,axp221-usb-power-supply" + "x-powers,axp223-usb-power-supply" + +The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight +variations such as the former being able to set the VBUS power supply max +current to 100mA, unlike the latter. + +This node is a subnode of the axp20x PMIC. + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + ... + }; + + usb-power-supply: usb-power-supply { + compatible = "x-powers,axp202-usb-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt new file mode 100644 index 000000000..f4d3b4a10 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/battery.txt @@ -0,0 +1,57 @@ +Battery Characteristics + +The devicetree battery node provides static battery characteristics. +In smart batteries, these are typically stored in non-volatile memory +on a fuel gauge chip. The battery node should be used where there is +no appropriate non-volatile memory, or it is unprogrammed/incorrect. + +Upstream dts files should not include battery nodes, unless the battery +represented cannot easily be replaced in the system by one of a +different type. This prevents unpredictable, potentially harmful, +behavior should a replacement that changes the battery type occur +without a corresponding update to the dtb. + +Required Properties: + - compatible: Must be "simple-battery" + +Optional Properties: + - voltage-min-design-microvolt: drained battery voltage + - energy-full-design-microwatt-hours: battery design energy + - charge-full-design-microamp-hours: battery design capacity + - precharge-current-microamp: current for pre-charge phase + - charge-term-current-microamp: current for charge termination phase + - constant-charge-current-max-microamp: maximum constant input current + - constant-charge-voltage-max-microvolt: maximum constant input voltage + +Battery properties are named, where possible, for the corresponding +elements in enum power_supply_property, defined in +https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h + +Batteries must be referenced by chargers and/or fuel-gauges +using a phandle. The phandle's property should be named +"monitored-battery". + +Example: + + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + constant-charge-current-max-microamp = <900000>; + constant-charge-voltage-max-microvolt = <4200000>; + }; + + charger: charger@11 { + .... + monitored-battery = <&bat>; + ... + }; + + fuel_gauge: fuel-gauge@22 { + .... + monitored-battery = <&bat>; + ... + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq2415x.txt b/Documentation/devicetree/bindings/power/supply/bq2415x.txt new file mode 100644 index 000000000..d0327f0b5 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq2415x.txt @@ -0,0 +1,47 @@ +Binding for TI bq2415x Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24150" + * "ti,bq24150" + * "ti,bq24150a" + * "ti,bq24151" + * "ti,bq24151a" + * "ti,bq24152" + * "ti,bq24153" + * "ti,bq24153a" + * "ti,bq24155" + * "ti,bq24156" + * "ti,bq24156a" + * "ti,bq24158" +- reg: integer, i2c address of the device. +- ti,current-limit: integer, initial maximum current charger can pull + from power supply in mA. +- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV. + The chip will use slow precharge if battery voltage + is below this value. +- ti,battery-regulation-voltage: integer, maximum charging voltage in mV. +- ti,charge-current: integer, maximum charging current in mA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in mA). +- ti,resistor-sense: integer, value of sensing resistor in milliohm. + +Optional properties: +- ti,usb-charger-detection: phandle to usb charger detection device. + (required for auto mode) + +Example from Nokia N900: + +bq24150a { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt new file mode 100644 index 000000000..9e517d307 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24190.txt @@ -0,0 +1,51 @@ +TI BQ24190 Li-Ion Battery Charger + +Required properties: +- compatible: contains one of the following: + * "ti,bq24190" + * "ti,bq24192i" +- reg: integer, I2C address of the charger. +- interrupts[-extended]: configuration for charger INT pin. + +Optional properties: +- monitored-battery: phandle of battery characteristics devicetree node + The charger uses the following battery properties: + + precharge-current-microamp: maximum charge current during precharge + phase (typically 20% of battery capacity). + + charge-term-current-microamp: a charge cycle terminates when the + battery voltage is above recharge threshold, and the current is below + this setting (typically 10% of battery capacity). + See also Documentation/devicetree/bindings/power/supply/battery.txt +- ti,system-minimum-microvolt: when power is connected and the battery is below + minimum system voltage, the system will be regulated above this setting. + +Notes: +- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default + charge current on USB SDP ports, among other features). To simulate this on + boards that wire the pin to a GPIO, set a gpio-hog. + +Example: + + bat: battery { + compatible = "simple-battery"; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + // etc. + }; + + bq24190: charger@6a { + compatible = "ti,bq24190"; + reg = <0x6a>; + interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>; + monitored-battery = <&bat>; + ti,system-minimum-microvolt = <3200000>; + }; + + &twl_gpio { + otg { + gpio-hog; + gpios = <6 0>; + output-high; + line-name = "otg-gpio"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt new file mode 100644 index 000000000..f8f5a1685 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24257.txt @@ -0,0 +1,62 @@ +Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24250" + * "ti,bq24251" + * "ti,bq24257" +- reg: integer, i2c address of the device. +- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in + conjunction with "interrupt-parent". +- ti,battery-regulation-voltage: integer, maximum charging voltage in uV. +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Optional properties: +- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. +- ti,current-limit: The maximum current to be drawn from the charger's input + (in uA). If this property is not specified, the input limit current is + set automatically using USB D+/D- signal based charger type detection. + If the hardware does not support the D+/D- based detection, a default + of 500,000 is used (=500mA) instead. +- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If + not specified a default of 6,5000,000 (=6.5V) is used. +- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic + power path management (in uV). If not specified a default of 4,360,000 + (=4.36V) is used. + +Example: + +bq24257 { + compatible = "ti,bq24257"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; +}; + +Example: + +bq24250 { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt new file mode 100644 index 000000000..c9dd17d14 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt @@ -0,0 +1,46 @@ +Binding for TI bq25890 Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq25890" +- reg: integer, i2c address of the device. +- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV); +- ti,charge-current: integer, maximum charging current (in uA); +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA); +- ti,precharge-current: integer, maximum charge current during precharge + phase (in uA); +- ti,minimum-sys-voltage: integer, when battery is charging and it is below + minimum system voltage, the system will be regulated above + minimum-sys-voltage setting (in uV); +- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV); +- ti,boost-max-current: integer, maximum allowed current draw in boost mode + (in uA). + +Optional properties: +- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz, + otherwise 1.5MHz; +- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the + input current will be the lower between the resistor setting and the IINLIM + register setting; +- ti,thermal-regulation-threshold: integer, temperature above which the charge + current is lowered, to avoid overheating (in degrees Celsius). If omitted, + the default setting will be used (120 degrees); + +Example: + +bq25890 { + compatible = "ti,bq25890"; + reg = <0x6a>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; + ti,precharge-current = <128000>; + ti,minimum-sys-voltage = <3600000>; + ti,boost-voltage = <5000000>; + ti,boost-max-current = <1000000>; + + ti,use-ilim-pin; + ti,thermal-regulation-threshold = <120>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt new file mode 100644 index 000000000..37994fdb1 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -0,0 +1,55 @@ +TI BQ27XXX fuel gauge family + +Required properties: +- compatible: contains one of the following: + * "ti,bq27200" - BQ27200 + * "ti,bq27210" - BQ27210 + * "ti,bq27500" - deprecated, use revision specific property below + * "ti,bq27510" - deprecated, use revision specific property below + * "ti,bq27520" - deprecated, use revision specific property below + * "ti,bq27500-1" - BQ27500/1 + * "ti,bq27510g1" - BQ27510-g1 + * "ti,bq27510g2" - BQ27510-g2 + * "ti,bq27510g3" - BQ27510-g3 + * "ti,bq27520g1" - BQ27520-g1 + * "ti,bq27520g2" - BQ27520-g2 + * "ti,bq27520g3" - BQ27520-g3 + * "ti,bq27520g4" - BQ27520-g4 + * "ti,bq27521" - BQ27521 + * "ti,bq27530" - BQ27530 + * "ti,bq27531" - BQ27531 + * "ti,bq27541" - BQ27541 + * "ti,bq27542" - BQ27542 + * "ti,bq27546" - BQ27546 + * "ti,bq27742" - BQ27742 + * "ti,bq27545" - BQ27545 + * "ti,bq27421" - BQ27421 + * "ti,bq27425" - BQ27425 + * "ti,bq27426" - BQ27426 + * "ti,bq27441" - BQ27441 + * "ti,bq27621" - BQ27621 +- reg: integer, I2C address of the fuel gauge. + +Optional properties: +- monitored-battery: phandle of battery characteristics node + The fuel gauge uses the following battery properties: + + energy-full-design-microwatt-hours + + charge-full-design-microamp-hours + + voltage-min-design-microvolt + Both or neither of the *-full-design-*-hours properties must be set. + See Documentation/devicetree/bindings/power/supply/battery.txt + +Example: + + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + }; + + bq27510g3: fuel-gauge@55 { + compatible = "ti,bq27510g3"; + reg = <0x55>; + monitored-battery = <&bat>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/charger-manager.txt b/Documentation/devicetree/bindings/power/supply/charger-manager.txt new file mode 100644 index 000000000..ec4fe9de3 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/charger-manager.txt @@ -0,0 +1,81 @@ +charger-manager bindings +~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "charger-manager" + - <>-supply : for regulator consumer + - cm-num-chargers : number of chargers + - cm-chargers : name of chargers + - cm-fuel-gauge : name of battery fuel gauge + - subnode <regulator> : + - cm-regulator-name : name of charger regulator + - subnode <cable> : + - cm-cable-name : name of charger cable + - cm-cable-extcon : name of extcon dev +(optional) - cm-cable-min : minimum current of cable +(optional) - cm-cable-max : maximum current of cable + +Optional properties : + - cm-name : charger manager's name (default : "battery") + - cm-poll-mode : polling mode (enum polling_modes) + - cm-poll-interval : polling interval + - cm-battery-stat : battery status (enum data_source) + - cm-fullbatt-* : data for full battery checking + - cm-thermal-zone : name of external thermometer's thermal zone + - cm-battery-* : threshold battery temperature for charging + -cold : critical cold temperature of battery for charging + -cold-in-minus : flag that cold temperature is in minus degrees + -hot : critical hot temperature of battery for charging + -temp-diff : temperature difference to allow recharging + - cm-dis/charging-max = limits of charging duration + +Example : + charger-manager@0 { + compatible = "charger-manager"; + chg-reg-supply = <&charger_regulator>; + + cm-name = "battery"; + /* Always polling ON : 30s */ + cm-poll-mode = <1>; + cm-poll-interval = <30000>; + + cm-fullbatt-vchkdrop-ms = <30000>; + cm-fullbatt-vchkdrop-volt = <150000>; + cm-fullbatt-soc = <100>; + + cm-battery-stat = <3>; + + cm-num-chargers = <3>; + cm-chargers = "charger0", "charger1", "charger2"; + + cm-fuel-gauge = "fuelgauge0"; + + cm-thermal-zone = "thermal_zone.1" + /* in deci centigrade */ + cm-battery-cold = <50>; + cm-battery-cold-in-minus; + cm-battery-hot = <800>; + cm-battery-temp-diff = <100>; + + /* Allow charging for 5hr */ + cm-charging-max = <18000000>; + /* Allow discharging for 2hr */ + cm-discharging-max = <7200000>; + + regulator@0 { + cm-regulator-name = "chg-reg"; + cable@0 { + cm-cable-name = "USB"; + cm-cable-extcon = "extcon-dev.0"; + cm-cable-min = <475000>; + cm-cable-max = <500000>; + }; + cable@1 { + cm-cable-name = "TA"; + cm-cable-extcon = "extcon-dev.0"; + cm-cable-min = <650000>; + cm-cable-max = <675000>; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt new file mode 100644 index 000000000..a04efa22d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt @@ -0,0 +1,31 @@ +Motorola CPCAP PMIC battery driver binding + +Required properties: +- compatible: Shall be "motorola,cpcap-battery" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "lowbph", "lowbpl", "chrgcurr1", "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "chg_isense", "batti" +- power-supplies: List of phandles for power-supplying devices, as + described in power_supply.txt. Typically a reference + to cpcap_charger. + +Example: + +cpcap_battery: battery { + compatible = "motorola,cpcap-battery"; + interrupts-extended = < + &cpcap 5 0 &cpcap 3 0 + &cpcap 20 0 &cpcap 54 0 + >; + interrupt-names = + "lowbph", "lowbpl", + "chrgcurr1", "battdetb"; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 5 &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "chg_isense", "batti"; + power-supplies = <&cpcap_charger>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt new file mode 100644 index 000000000..80bd873c3 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt @@ -0,0 +1,37 @@ +Motorola CPCAP PMIC battery charger binding + +Required properties: +- compatible: Shall be "motorola,mapphone-cpcap-charger" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr1", "vbusvld", "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "vbus", "chg_isense", "batti" + +Optional properties: +- mode-gpios: Optionally CPCAP charger can have a companion wireless + charge controller that is controlled with two GPIOs + that are active low. + +Example: + +cpcap_charger: charger { + compatible = "motorola,mapphone-cpcap-charger"; + interrupts-extended = < + &cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0 + &cpcap 22 0 &cpcap 20 0 &cpcap 19 0 &cpcap 54 0 + >; + interrupt-names = + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr1", "vbusvld", "battdetb"; + mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW + &gpio3 23 GPIO_ACTIVE_LOW>; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 2 &cpcap_adc 5 + &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "vbus", "chg_isense", + "batti"; +}; diff --git a/Documentation/devicetree/bindings/power/supply/da9150-charger.txt b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt new file mode 100644 index 000000000..f3906663c --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt @@ -0,0 +1,26 @@ +Dialog Semiconductor DA9150 Charger Power Supply bindings + +Required properties: +- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply + +Optional properties: +- io-channels: List of phandle and IIO specifier pairs +- io-channel-names: List of channel names used by charger + ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"] + (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info) + + +Example: + + da9150-charger { + compatible = "dlg,da9150-charger"; + + io-channels = <&gpadc 0>, + <&gpadc 2>, + <&gpadc 8>, + <&gpadc 5>; + io-channel-names = "CHAN_IBUS", + "CHAN_VBUS", + "CHAN_TJUNC", + "CHAN_VBAT"; + }; diff --git a/Documentation/devicetree/bindings/power/supply/da9150-fg.txt b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt new file mode 100644 index 000000000..00236fe3e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt @@ -0,0 +1,23 @@ +Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings + +Required properties: +- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply + +Optional properties: +- dlg,update-interval: Interval time (milliseconds) between battery level checks. +- dlg,warn-soc-level: Battery discharge level (%) where warning event raised. + [1 - 100] +- dlg,crit-soc-level: Battery discharge level (%) where critical event raised. + This value should be lower than the warning level. + [1 - 100] + + +Example: + + fuel-gauge { + compatible = "dlg,da9150-fuel-gauge"; + + dlg,update-interval = <10000>; + dlg,warn-soc-level = /bits/ 8 <15>; + dlg,crit-soc-level = /bits/ 8 <5>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/gpio-charger.txt b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt new file mode 100644 index 000000000..adbb5dc5b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt @@ -0,0 +1,27 @@ +gpio-charger + +Required properties : + - compatible : "gpio-charger" + - gpios : GPIO indicating the charger presence. + See GPIO binding in bindings/gpio/gpio.txt . + - charger-type : power supply type, one of + unknown + battery + ups + mains + usb-sdp (USB standard downstream port) + usb-dcp (USB dedicated charging port) + usb-cdp (USB charging downstream port) + usb-aca (USB accessory charger adapter) + +Example: + + usb_charger: charger { + compatible = "gpio-charger"; + charger-type = "usb-sdp"; + gpios = <&gpf0 2 0 0 0>; + } + + battery { + power-supplies = <&usb_charger>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/isp1704.txt b/Documentation/devicetree/bindings/power/supply/isp1704.txt new file mode 100644 index 000000000..fa3596907 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/isp1704.txt @@ -0,0 +1,17 @@ +Binding for NXP ISP1704 USB Charger Detection + +Required properties: +- compatible: Should contain one of the following: + * "nxp,isp1704" +- nxp,enable-gpio: Should contain a phandle + gpio-specifier + to the GPIO pin connected to the chip's enable pin. +- usb-phy: Should contain a phandle to the USB PHY + the ISP1704 is connected to. + +Example: + +isp1704 { + compatible = "nxp,isp1704"; + nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>; + usb-phy = <&usb2_phy>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt new file mode 100644 index 000000000..5485633b1 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt @@ -0,0 +1,21 @@ +LEGO MINDSTORMS EV3 Battery +~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery. +It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is +detected by a key switch in the battery compartment. + +Required properties: + - compatible: Must be "lego,ev3-battery" + - io-channels: phandles to analog inputs for reading voltage and current + - io-channel-names: Must be "voltage", "current" + - rechargeable-gpios: phandle to the rechargeable battery indication gpio + +Example: + + battery { + compatible = "lego,ev3-battery"; + io-channels = <&adc 4>, <&adc 3>; + io-channel-names = "voltage", "current"; + rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt new file mode 100644 index 000000000..0355a4b68 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt @@ -0,0 +1,43 @@ +Binding for TI/National Semiconductor LP8727 Charger + +Required properties: +- compatible: "ti,lp8727" +- reg: I2C slave address 27h + +Optional properties: +- interrupts: interrupt specifier (see interrupt binding[0]) +- debounce-ms: interrupt debounce time. (u32) + +AC and USB charging parameters +- charger-type: "ac" or "usb" (string) +- eoc-level: value of 'enum lp8727_eoc_level' (u8) +- charging-current: value of 'enum lp8727_ichg' (u8) + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example) + +lp8727@27 { + compatible = "ti,lp8727"; + reg = <0x27>; + + /* GPIO 134 is used for LP8728 interrupt pin */ + interrupt-parent = <&gpio5>; /* base = 128 */ + interrupts = <6 0x2>; /* offset = 6, falling edge type */ + + debounce-ms = <300>; + + /* AC charger: 5% EOC and 500mA charging current */ + ac { + charger-type = "ac"; + eoc-level = /bits/ 8 <0>; + charging-current = /bits/ 8 <4>; + }; + + /* USB charger: 10% EOC and 400mA charging current */ + usb { + charger-type = "usb"; + eoc-level = /bits/ 8 <1>; + charging-current = /bits/ 8 <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt new file mode 100644 index 000000000..3b9ba147b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt @@ -0,0 +1,28 @@ +binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges + +All chips measure battery capacity. +The LTC2942 is pin compatible with the LTC2941, it adds voltage and +temperature monitoring, and is runtime detected. LTC2943 and LTC2944 +is software compatible, uses a slightly different conversion formula +for the charge counter and adds voltage, current and temperature monitoring. + +Required properties: +- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943" + or "lltc,ltc2944" which also indicates the type of I2C chip attached. +- reg: The 7-bit I2C address. +- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit + negative value when the battery has been connected to the wrong end of the + resistor. +- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet. + This determines the range and accuracy of the gauge. The value is programmed + into the chip only if it differs from the current setting. The setting is + lost when the battery is disconnected. + +Example from the Topic Miami Florida board: + + fuelgauge: ltc2943@64 { + compatible = "lltc,ltc2943"; + reg = <0x64>; + lltc,resistor-sense = <15>; + lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ + }; diff --git a/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt new file mode 100644 index 000000000..71f2840e8 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt @@ -0,0 +1,27 @@ +ltc3651-charger + +Required properties: + - compatible: "lltc,ltc3651-charger" + - lltc,acpr-gpios: Connect to ACPR output. See remark below. + +Optional properties: + - lltc,fault-gpios: Connect to FAULT output. See remark below. + - lltc,chrg-gpios: Connect to CHRG output. See remark below. + +The ltc3651 outputs are open-drain type and active low. The driver assumes the +GPIO reports "active" when the output is asserted, so if the pins have been +connected directly, the GPIO flags should be set to active low also. + +The driver will attempt to aquire interrupts for all GPIOs to detect changes in +line state. If the system is not capabale of providing interrupts, the driver +cannot report changes and userspace will need to periodically read the sysfs +attributes to detect changes. + +Example: + + charger: battery-charger { + compatible = "lltc,ltc3651-charger"; + lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>; + lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>; + lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max17042_battery.txt b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt new file mode 100644 index 000000000..3f3894aae --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt @@ -0,0 +1,31 @@ +max17042_battery +~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "maxim,max17042" + +Optional properties : + - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms + (datasheet-recommended value is 10000). + Defining this property enables current-sense functionality. + +Optional threshold properties : + If skipped the condition won't be reported. + - maxim,cold-temp : Temperature threshold to report battery + as cold (in tenths of degree Celsius). + - maxim,over-heat-temp : Temperature threshold to report battery + as over heated (in tenths of degree Celsius). + - maxim,dead-volt : Voltage threshold to report battery + as dead (in mV). + - maxim,over-volt : Voltage threshold to report battery + as over voltage (in mV). + +Example: + + battery-charger@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4300>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt new file mode 100644 index 000000000..bab947fef --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt @@ -0,0 +1,24 @@ +Maxim Semiconductor MAX8903 Battery Charger bindings + +Required properties: +- compatible: "maxim,max8903" for MAX8903 Battery Charger +- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided +- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided + +Optional properties: +- cen-gpios: Charge enable pin (active low, output) +- chg-gpios: Charger status pin (active low, input) +- flt-gpios: Fault pin (active low, output) +- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output) +- usus-gpios: USB suspend pin (active high, output) + + +Example: + + max8903-charger { + compatible = "maxim,max8903"; + dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; + cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max8925_battery.txt b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt new file mode 100644 index 000000000..d7e3e0c0f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt @@ -0,0 +1,18 @@ +max8925-battery bindings +~~~~~~~~~~~~~~~~ + +Optional properties : + - batt-detect: whether support battery detect + - topoff-threshold: set charging current in topoff mode + - fast-charge: set charging current in fast mode + - no-temp-support: whether support temperature protection detect + - no-insert-detect: whether support insert detect + +Example: + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt new file mode 100644 index 000000000..55967a0be --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt @@ -0,0 +1,26 @@ +Devicetree bindings for Maxim DS2760 +==================================== + +The ds2760 is a w1 slave device and must hence have its sub-node in DT +under a w1 bus master node. + +The device exposes a power supply, so the details described in +Documentation/devicetree/bindings/power/supply/power_supply.txt apply. + +Required properties: +- compatible: must be "maxim,ds2760" + +Optional properties: +- power-supplies: Refers to one or more power supplies connected to + this battery. +- maxim,pmod-enabled: This boolean property enables the DS2760 to enter + sleep mode when the DQ line goes low for greater + than 2 seconds and leave sleep Mode when the DQ + line goes high. +- maxim,cache-time-ms: Time im milliseconds to cache the data for. When + this time expires, the values are read again from + the hardware. Defaults to 1000. +- rated-capacity-microamp-hours: + The rated capacity of the battery, in mAh. + If not specified, the value stored in the + non-volatile chip memory is used. diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt new file mode 100644 index 000000000..f956247d4 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt @@ -0,0 +1,23 @@ +Maxim MAX14656 / AL32 USB Charger Detector + +Required properties : +- compatible : "maxim,max14656"; +- reg: i2c slave address +- interrupts: interrupt line + +Example: + +&i2c2 { + clock-frequency = <50000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + + max14656@35 { + compatible = "maxim,max14656"; + reg = <0x35>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_detect>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/olpc_battery.txt b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt new file mode 100644 index 000000000..c8901b399 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt @@ -0,0 +1,5 @@ +OLPC battery +~~~~~~~~~~~~ + +Required properties: + - compatible : "olpc,xo1-battery" diff --git a/Documentation/devicetree/bindings/power/supply/power_supply.txt b/Documentation/devicetree/bindings/power/supply/power_supply.txt new file mode 100644 index 000000000..8391bfa0e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/power_supply.txt @@ -0,0 +1,23 @@ +Power Supply Core Support + +Optional Properties: + - power-supplies : This property is added to a supply in order to list the + devices which supply it power, referenced by their phandles. + +Example: + + usb-charger: power@e { + compatible = "some,usb-charger"; + ... + }; + + ac-charger: power@c { + compatible = "some,ac-charger"; + ... + }; + + battery@b { + compatible = "some,battery"; + ... + power-supplies = <&usb-charger>, <&ac-charger>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt new file mode 100644 index 000000000..747899223 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt @@ -0,0 +1,48 @@ +Qualcomm Coincell Charger: + +The hardware block controls charging for a coincell or capacitor that is +used to provide power backup for certain features of the power management +IC (PMIC) + +- compatible: + Usage: required + Value type: <string> + Definition: must be: "qcom,pm8941-coincell" + +- reg: + Usage: required + Value type: <u32> + Definition: base address of the coincell charger registers + +- qcom,rset-ohms: + Usage: required + Value type: <u32> + Definition: resistance (in ohms) for current-limiting resistor + must be one of: 800, 1200, 1700, 2100 + +- qcom,vset-millivolts: + Usage: required + Value type: <u32> + Definition: voltage (in millivolts) to apply for charging + must be one of: 2500, 3000, 3100, 3200 + +- qcom,charger-disable: + Usage: optional + Value type: <boolean> + Definition: defining this property disables charging + +This charger is a sub-node of one of the 8941 PMIC blocks, and is specified +as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and +../mfd/qcom-pm8xxx.txt + +Example: + + pm8941@0 { + coincell@2800 { + compatible = "qcom,pm8941-coincell"; + reg = <0x2800>; + + qcom,rset-ohms = <2100>; + qcom,vset-millivolts = <3000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt new file mode 100644 index 000000000..06f8a5ddb --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt @@ -0,0 +1,150 @@ +Qualcomm Switch-Mode Battery Charger and Boost + +PROPERTIES +- compatible: + Usage: required + Value type: <stringlist> + Description: Must be one of: + - "qcom,pm8941-charger" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Description: Base address of registers for SMBB block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Description: The format of the specifier is defined by the binding document + describing the node's interrupt parent. Must contain one + specifier for each of the following interrupts, in order: + - charge done + - charge fast mode + - charge trickle mode + - battery temperature ok + - battery present + - charger disconnected + - USB-in valid + - DC-in valid + +- interrupt-names: + Usage: required + Value type: <stringlist> + Description: Must contain the following list, strictly ordered: + "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid" + +- qcom,fast-charge-current-limit: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum charge current; May be clamped to safety limits. + +- qcom,fast-charge-low-threshold-voltage: + Usage: optional (default: 3.2V, or pre-configured value) + Value type: <u32>; uV; range [2.1V : 3.6V] + Description: Battery voltage limit above which fast charging may operate; + Below this value linear or switch-mode auto-trickle-charging + will operate. + +- qcom,fast-charge-high-threshold-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which fast charging may operate; + The fast charger will attempt to charge the battery to this + voltage. May be clamped to safety limits. + +- qcom,fast-charge-safe-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Maximum safe battery voltage; May be pre-set by bootloader, in + which case, setting this will harmlessly fail. The property + 'fast-charge-high-watermark' will be clamped by this value. + +- qcom,fast-charge-safe-current: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum safe battery charge current; May pre-set by bootloader, + in which case, setting this will harmlessly fail. The property + 'qcom,fast-charge-current-limit' will be clamped by this value. + +- qcom,auto-recharge-threshold-voltage: + Usage: optional (default: 4.1V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which auto-recharge functionality + will restart charging after end-of-charge; The high cutoff + limit for auto-recharge is 5% above this value. + +- qcom,minimum-input-voltage: + Usage: optional (default: 4.3V, or pre-configured value) + Value type: <u32>; uV; range [4.2V : 9.6V] + Description: Input voltage level above which charging may operate + +- qcom,dc-current-limit: + Usage: optional (default: 100mA, or pre-configured value) + Value type: <u32>; uA; range [100mA : 2.5A] + Description: Default DC charge current limit + +- qcom,disable-dc: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Disable DC charger + +- qcom,jeita-extended-temp-range: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Enable JEITA extended temperature range; This does *not* + adjust the maximum charge voltage or current in the extended + temperature range. It only allows charging when the battery + is in the extended temperature range. Voltage/current + regulation must be done externally to fully comply with + the JEITA safety guidelines if this flag is set. + +- usb_otg_in-supply: + Usage: optional + Value type: <phandle> + Description: Reference to the regulator supplying power to the USB_OTG_IN + pin. + +child nodes: +- otg-vbus: + Usage: optional + Description: This node defines a regulator used to control the direction + of VBUS voltage - specifically: whether to supply voltage + to VBUS for host mode operation of the OTG port, or allow + input voltage from external VBUS for charging. In the + hardware, the supply for this regulator comes from + usb_otg_in-supply. + +EXAMPLE +charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000 0x700>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + + qcom,fast-charge-current-limit = <1000000>; + qcom,dc-charge-current-limit = <1000000>; + usb_otg_in-supply = <&pm8941_5vs1>; + + otg-vbus {}; +}; diff --git a/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt new file mode 100644 index 000000000..1e6107c75 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt @@ -0,0 +1,46 @@ +Binding for Richtek rt9455 battery charger + +Required properties: +- compatible: it should contain one of the following: + "richtek,rt9455". +- reg: integer, i2c address of the device. +- interrupts: interrupt mapping for GPIO IRQ, it should be + configured with IRQ_TYPE_LEVEL_LOW flag. +- richtek,output-charge-current: integer, output current from the charger to the + battery, in uA. +- richtek,end-of-charge-percentage: integer, percent of the output charge current. + When the current in constant-voltage phase drops + below output_charge_current x end-of-charge-percentage, + charge is terminated. +- richtek,battery-regulation-voltage: integer, maximum battery voltage in uV. +- richtek,boost-output-voltage: integer, maximum voltage provided to consumer + devices, when the charger is in boost mode, in uV. + +Optional properties: +- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to + decrease voltage level when the over current + of the input power source occurs. + This prevents input voltage drop due to insufficient + current provided by the power source. + Default: 4500000 uV (4.5V) +- richtek,avg-input-current-regulation: integer, input current value in uA drained by the + charger from the power source. + Default: 500000 uA (500mA) + +Example: + +rt9455@22 { + compatible = "richtek,rt9455"; + reg = <0x22>; + + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + richtek,output-charge-current = <500000>; + richtek,end-of-charge-percentage = <10>; + richtek,battery-regulation-voltage = <4200000>; + richtek,boost-output-voltage = <5050000>; + + richtek,min-input-voltage-regulation = <4500000>; + richtek,avg-input-current-regulation = <500000>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/rx51-battery.txt b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt new file mode 100644 index 000000000..90438453d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt @@ -0,0 +1,25 @@ +Binding for Nokia N900 battery + +The Nokia N900 battery status can be read via the TWL4030's A/D converter. + +Required properties: +- compatible: Should contain one of the following: + * "nokia,n900-battery" +- io-channels: Should contain IIO channel specifiers + for each element in io-channel-names. +- io-channel-names: Should contain the following values: + * "temp" - The ADC channel for temperature reading + * "bsi" - The ADC channel for battery size identification + * "vbat" - The ADC channel to measure the battery voltage + +Example from Nokia N900: + +battery: n900-battery { + compatible = "nokia,n900-battery"; + io-channels = <&twl4030_madc 0>, + <&twl4030_madc 4>, + <&twl4030_madc 12>; + io-channel-names = "temp", + "bsi", + "vbat"; +}; diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt new file mode 100644 index 000000000..4b2195571 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt @@ -0,0 +1,66 @@ +Binding for sbs-manager + +Required properties: +- compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. +- reg: integer, i2c address of the device. Should be <0xa>. +Optional properties: +- gpio-controller: Marks the port as GPIO controller. + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- #gpio-cells: Should be <2>. The first cell is the pin number, the second cell + is used to specify optional parameters: + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. + +From OS view the device is basically an i2c-mux used to communicate with up to +four smart battery devices at address 0xb. The driver actually implements this +behaviour. So standard i2c-mux nodes can be used to register up to four slave +batteries. Channels will be numerated starting from 1 to 4. + +Example: + +batman@a { + compatible = "lltc,ltc1760", "sbs,sbs-manager"; + reg = <0x0a>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + battery@b { + compatible = "ti,bq2060", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 1 1>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + battery@b { + compatible = "ti,bq2060", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 2 1>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + battery@b { + compatible = "ti,bq2060", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 3 1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt new file mode 100644 index 000000000..4e78e5101 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt @@ -0,0 +1,27 @@ +SBS sbs-battery +~~~~~~~~~~ + +Required properties : + - compatible: "<vendor>,<part-number>", "sbs,sbs-battery" as fallback. The + part number compatible string might be used in order to take care of + vendor specific registers. + Known <vendor>,<part-number>: + ti,bq20z75 + +Optional properties : + - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c + IO failure. + - sbs,poll-retry-count : The number of times to try looking for new status + after an external change notification. + - sbs,battery-detect-gpios : The gpio which signals battery detection and + a flag specifying its polarity. + +Example: + + battery@b { + compatible = "ti,bq20z75", "sbs,sbs-battery"; + reg = <0xb>; + sbs,i2c-retry-count = <2>; + sbs,poll-retry-count = <10>; + sbs,battery-detect-gpios = <&gpio-controller 122 1>; + } diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt new file mode 100644 index 000000000..84e74151e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt @@ -0,0 +1,21 @@ +SBS sbs-charger +~~~~~~~~~~ + +Required properties: + - compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. + +Optional properties: +- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with + "interrupt-parent". If an interrupt is not provided the driver will switch + automatically to polling. + +Example: + + ltc4100@9 { + compatible = "lltc,ltc4100", "sbs,sbs-charger"; + reg = <0x9>; + interrupt-parent = <&gpio6>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt new file mode 100644 index 000000000..de45e1a2a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt @@ -0,0 +1,39 @@ +TI BQ24735 Charge Controller +~~~~~~~~~~ + +Required properties : + - compatible : "ti,bq24735" + +Optional properties : + - interrupts : Specify the interrupt to be used to trigger when the AC + adapter is either plugged in or removed. + - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter + status. This is a Host GPIO that is configured as an input and connected + to the ACOK pin on the bq24735. Note: for backwards compatibility reasons, + the GPIO must be active on AC adapter absence despite ACOK being active + (high) on AC adapter presence. + - ti,charge-current : Used to control and set the charging current. This value + must be between 128mA and 8.128A with a 64mA step resolution. The POR value + is 0x0000h. This number is in mA (e.g. 8192), see spec for more information + about the ChargeCurrent (0x14h) register. + - ti,charge-voltage : Used to control and set the charging voltage. This value + must be between 1.024V and 19.2V with a 16mV step resolution. The POR value + is 0x0000h. This number is in mV (e.g. 19200), see spec for more information + about the ChargeVoltage (0x15h) register. + - ti,input-current : Used to control and set the charger input current. This + value must be between 128mA and 8.064A with a 128mA step resolution. The + POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for + more information about the InputCurrent (0x3fh) register. + - ti,external-control : Indicates that the charger is configured externally + and that the host should not attempt to enable/disable charging or set the + charge voltage/current. + - poll-interval : In case 'interrupts' is not specified, poll AC adapter + presence with this interval (milliseconds). + +Example: + + bq24735@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + ti,ac-detect-gpios = <&gpio 72 0x1>; + } diff --git a/Documentation/devicetree/bindings/power/supply/tps65090.txt b/Documentation/devicetree/bindings/power/supply/tps65090.txt new file mode 100644 index 000000000..8e5e0d391 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65090.txt @@ -0,0 +1,17 @@ +TPS65090 Frontend PMU with Switchmode Charger + +Required Properties: +-compatible: "ti,tps65090-charger" + +Optional Properties: +-ti,enable-low-current-chrg: Enables charging when a low current is detected + while the default logic is to stop charging. + +This node is a subnode of the tps65090 PMIC. + +Example: + + tps65090-charger { + compatible = "ti,tps65090-charger"; + ti,enable-low-current-chrg; + }; diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt new file mode 100644 index 000000000..a11072c5a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt @@ -0,0 +1,17 @@ +TPS65217 Charger + +Required Properties: +-compatible: "ti,tps65217-charger" +-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change. + Should be <0> for the USB charger and <1> for the AC adapter. +-interrupt-names: Should be "USB" and "AC" + +This node is a subnode of the tps65217 PMIC. + +Example: + + tps65217-charger { + compatible = "ti,tps65217-charger"; + interrupts = <0>, <1>; + interrupt-names = "USB", "AC"; + }; diff --git a/Documentation/devicetree/bindings/power/supply/twl-charger.txt b/Documentation/devicetree/bindings/power/supply/twl-charger.txt new file mode 100644 index 000000000..3b4ea1b73 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/twl-charger.txt @@ -0,0 +1,30 @@ +TWL BCI (Battery Charger Interface) + +The battery charger needs to interact with the USB phy in order +to know when charging is permissible, and when there is a connection +or disconnection. + +The choice of phy cannot be configured at a hardware level, so there +is no value in explicit configuration in device-tree. Rather +if there is a sibling of the BCI node which is compatible with +"ti,twl4030-usb", then that is used to determine when and how +use USB power for charging. + +Required properties: +- compatible: + - "ti,twl4030-bci" +- interrupts: two interrupt lines from the TWL SIH (secondary + interrupt handler) - interrupts 9 and 2. + +Optional properties: +- ti,bb-uvolt: microvolts for charging the backup battery. +- ti,bb-uamp: microamps for charging the backup battery. + +Examples: + +bci { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; |