diff options
Diffstat (limited to 'Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt | 137 |
1 files changed, 137 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt b/Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt new file mode 100644 index 000000000..9b86d1eff --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt @@ -0,0 +1,137 @@ +RPMH RSC: +------------ + +Resource Power Manager Hardened (RPMH) is the mechanism for communicating with +the hardened resource accelerators on Qualcomm SoCs. Requests to the resources +can be written to the Trigger Command Set (TCS) registers and using a (addr, +val) pair and triggered. Messages in the TCS are then sent in sequence over an +internal bus. + +The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity +(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and +active/wake resource requests. Multiple such DRVs can exist in a SoC and can +be written to from Linux. The structure of each DRV follows the same template +with a few variations that are captured by the properties here. + +A TCS may be triggered from Linux or triggered by the F/W after all the CPUs +have powered off to facilitate idle power saving. TCS could be classified as - + + ACTIVE /* Triggered by Linux */ + SLEEP /* Triggered by F/W */ + WAKE /* Triggered by F/W */ + CONTROL /* Triggered by F/W */ + +The order in which they are described in the DT, should match the hardware +configuration. + +Requests can be made for the state of a resource, when the subsystem is active +or idle. When all subsystems like Modem, GPU, CPU are idle, the resource state +will be an aggregate of the sleep votes from each of those subsystems. Clients +may request a sleep value for their shared resources in addition to the active +mode requests. + +Properties: + +- compatible: + Usage: required + Value type: <string> + Definition: Should be "qcom,rpmh-rsc". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: The first register specifies the base address of the + DRV(s). The number of DRVs in the dependent on the RSC. + The tcs-offset specifies the start address of the + TCS in the DRVs. + +- reg-names: + Usage: required + Value type: <string> + Definition: Maps the register specified in the reg property. Must be + "drv-0", "drv-1", "drv-2" etc and "tcs-offset". The + +- interrupts: + Usage: required + Value type: <prop-encoded-interrupt> + Definition: The interrupt that trips when a message complete/response + is received for this DRV from the accelerators. + +- qcom,drv-id: + Usage: required + Value type: <u32> + Definition: The id of the DRV in the RSC block that will be used by + this controller. + +- qcom,tcs-config: + Usage: required + Value type: <prop-encoded-array> + Definition: The tuple defining the configuration of TCS. + Must have 2 cells which describe each TCS type. + <type number_of_tcs>. + The order of the TCS must match the hardware + configuration. + - Cell #1 (TCS Type): TCS types to be specified - + ACTIVE_TCS + SLEEP_TCS + WAKE_TCS + CONTROL_TCS + - Cell #2 (Number of TCS): <u32> + +- label: + Usage: optional + Value type: <string> + Definition: Name for the RSC. The name would be used in trace logs. + +Drivers that want to use the RSC to communicate with RPMH must specify their +bindings as child nodes of the RSC controllers they wish to communicate with. + +Example 1: + +For a TCS whose RSC base address is is 0x179C0000 and is at a DRV id of 2, the +register offsets for DRV2 start at 0D00, the register calculations are like +this - +DRV0: 0x179C0000 +DRV2: 0x179C0000 + 0x10000 = 0x179D0000 +DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000 +TCS-OFFSET: 0xD00 + + apps_rsc: rsc@179c0000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x179c0000 0x10000>, + <0x179d0000 0x10000>, + <0x179e0000 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 2>, + <SLEEP_TCS 3>, + <WAKE_TCS 3>, + <CONTROL_TCS 1>; + }; + +Example 2: + +For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the +register offsets for DRV0 start at 01C00, the register calculations are like +this - +DRV0: 0xAF20000 +TCS-OFFSET: 0x1C00 + + disp_rsc: rsc@af20000 { + label = "disp_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0xaf20000 0x10000>; + reg-names = "drv-0"; + interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0x1c00>; + qcom,drv-id = <0>; + qcom,tcs-config = <ACTIVE_TCS 0>, + <SLEEP_TCS 1>, + <WAKE_TCS 1>, + <CONTROL_TCS 0>; + }; |