diff options
Diffstat (limited to 'drivers/tty/serial/8250/8250_lpc18xx.c')
| -rw-r--r-- | drivers/tty/serial/8250/8250_lpc18xx.c | 226 |
1 files changed, 226 insertions, 0 deletions
diff --git a/drivers/tty/serial/8250/8250_lpc18xx.c b/drivers/tty/serial/8250/8250_lpc18xx.c new file mode 100644 index 000000000..eddf11937 --- /dev/null +++ b/drivers/tty/serial/8250/8250_lpc18xx.c @@ -0,0 +1,226 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Serial port driver for NXP LPC18xx/43xx UART + * + * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com> + * + * Based on 8250_mtk.c: + * Copyright (c) 2014 MundoReader S.L. + * Matthias Brugger <matthias.bgg@gmail.com> + */ + +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "8250.h" + +/* Additional LPC18xx/43xx 8250 registers and bits */ +#define LPC18XX_UART_RS485CTRL (0x04c / sizeof(u32)) +#define LPC18XX_UART_RS485CTRL_NMMEN BIT(0) +#define LPC18XX_UART_RS485CTRL_DCTRL BIT(4) +#define LPC18XX_UART_RS485CTRL_OINV BIT(5) +#define LPC18XX_UART_RS485DLY (0x054 / sizeof(u32)) +#define LPC18XX_UART_RS485DLY_MAX 255 + +struct lpc18xx_uart_data { + struct uart_8250_dma dma; + struct clk *clk_uart; + struct clk *clk_reg; + int line; +}; + +static int lpc18xx_rs485_config(struct uart_port *port, + struct serial_rs485 *rs485) +{ + struct uart_8250_port *up = up_to_u8250p(port); + u32 rs485_ctrl_reg = 0; + u32 rs485_dly_reg = 0; + unsigned baud_clk; + + if (rs485->flags & SER_RS485_ENABLED) + memset(rs485->padding, 0, sizeof(rs485->padding)); + else + memset(rs485, 0, sizeof(*rs485)); + + rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | + SER_RS485_RTS_AFTER_SEND; + + if (rs485->flags & SER_RS485_ENABLED) { + rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN | + LPC18XX_UART_RS485CTRL_DCTRL; + + if (rs485->flags & SER_RS485_RTS_ON_SEND) { + rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV; + rs485->flags &= ~SER_RS485_RTS_AFTER_SEND; + } else { + rs485->flags |= SER_RS485_RTS_AFTER_SEND; + } + } + + if (rs485->delay_rts_after_send) { + baud_clk = port->uartclk / up->dl_read(up); + rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send + * baud_clk, MSEC_PER_SEC); + + if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX) + rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX; + + /* Calculate the resulting delay in ms */ + rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC) + / baud_clk; + } + + /* Delay RTS before send not supported */ + rs485->delay_rts_before_send = 0; + + serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg); + serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg); + + port->rs485 = *rs485; + + return 0; +} + +static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value) +{ + /* + * For DMA mode one must ensure that the UART_FCR_DMA_SELECT + * bit is set when FIFO is enabled. Even if DMA is not used + * setting this bit doesn't seem to affect anything. + */ + if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO)) + value |= UART_FCR_DMA_SELECT; + + offset = offset << p->regshift; + writel(value, p->membase + offset); +} + +static int lpc18xx_serial_probe(struct platform_device *pdev) +{ + struct lpc18xx_uart_data *data; + struct uart_8250_port uart; + struct resource *res; + int irq, ret; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "irq not found"); + return irq; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "memory resource not found"); + return -EINVAL; + } + + memset(&uart, 0, sizeof(uart)); + + uart.port.membase = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (!uart.port.membase) + return -ENOMEM; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->clk_uart = devm_clk_get(&pdev->dev, "uartclk"); + if (IS_ERR(data->clk_uart)) { + dev_err(&pdev->dev, "uart clock not found\n"); + return PTR_ERR(data->clk_uart); + } + + data->clk_reg = devm_clk_get(&pdev->dev, "reg"); + if (IS_ERR(data->clk_reg)) { + dev_err(&pdev->dev, "reg clock not found\n"); + return PTR_ERR(data->clk_reg); + } + + ret = clk_prepare_enable(data->clk_reg); + if (ret) { + dev_err(&pdev->dev, "unable to enable reg clock\n"); + return ret; + } + + ret = clk_prepare_enable(data->clk_uart); + if (ret) { + dev_err(&pdev->dev, "unable to enable uart clock\n"); + goto dis_clk_reg; + } + + ret = of_alias_get_id(pdev->dev.of_node, "serial"); + if (ret >= 0) + uart.port.line = ret; + + data->dma.rx_param = data; + data->dma.tx_param = data; + + spin_lock_init(&uart.port.lock); + uart.port.dev = &pdev->dev; + uart.port.irq = irq; + uart.port.iotype = UPIO_MEM32; + uart.port.mapbase = res->start; + uart.port.regshift = 2; + uart.port.type = PORT_16550A; + uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST; + uart.port.uartclk = clk_get_rate(data->clk_uart); + uart.port.private_data = data; + uart.port.rs485_config = lpc18xx_rs485_config; + uart.port.serial_out = lpc18xx_uart_serial_out; + + uart.dma = &data->dma; + uart.dma->rxconf.src_maxburst = 1; + uart.dma->txconf.dst_maxburst = 1; + + ret = serial8250_register_8250_port(&uart); + if (ret < 0) { + dev_err(&pdev->dev, "unable to register 8250 port\n"); + goto dis_uart_clk; + } + + data->line = ret; + platform_set_drvdata(pdev, data); + + return 0; + +dis_uart_clk: + clk_disable_unprepare(data->clk_uart); +dis_clk_reg: + clk_disable_unprepare(data->clk_reg); + return ret; +} + +static int lpc18xx_serial_remove(struct platform_device *pdev) +{ + struct lpc18xx_uart_data *data = platform_get_drvdata(pdev); + + serial8250_unregister_port(data->line); + clk_disable_unprepare(data->clk_uart); + clk_disable_unprepare(data->clk_reg); + + return 0; +} + +static const struct of_device_id lpc18xx_serial_match[] = { + { .compatible = "nxp,lpc1850-uart" }, + { }, +}; +MODULE_DEVICE_TABLE(of, lpc18xx_serial_match); + +static struct platform_driver lpc18xx_serial_driver = { + .probe = lpc18xx_serial_probe, + .remove = lpc18xx_serial_remove, + .driver = { + .name = "lpc18xx-uart", + .of_match_table = lpc18xx_serial_match, + }, +}; +module_platform_driver(lpc18xx_serial_driver); + +MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>"); +MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices"); +MODULE_LICENSE("GPL v2"); |