1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
Binding for Samsung S5M8767 regulator block
===========================================
This is a part of device tree bindings for S5M family multi-function devices.
More information can be found in bindings/mfd/sec-core.txt file.
The S5M8767 device provide buck and LDO regulators.
To register these with regulator framework instantiate under main device node
a sub-node named "regulators" with more sub-nodes for each regulator using the
common regulator binding documented in:
- Documentation/devicetree/bindings/regulator/regulator.txt
Required properties of the main device node (the parent!):
- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
[1] If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
property is specified, then all the eight voltage values for the
's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
Optional properties of the main device node (the parent!):
- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
units for buck2 when changing voltage using gpio dvs. Refer to [1] below
for additional information.
- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
units for buck3 when changing voltage using gpio dvs. Refer to [1] below
for additional information.
- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
units for buck4 when changing voltage using gpio dvs. Refer to [1] below
for additional information.
- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
Additional properties required if either of the optional properties are used:
- s5m8767,pmic-buck-default-dvs-idx: Default voltage setting selected from
the possible 8 options selectable by the dvs gpios. The value of this
property should be between 0 and 7. If not specified or if out of range, the
default value of this property is set to 0.
- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
for dvs. The format of the gpio specifier depends in the gpio controller.
Names of regulators supported by S5M8767 device:
- LDOn
- valid values for n are 1 to 28
- Example: LDO1, LDO2, LDO28
- BUCKn
- valid values for n are 1 to 9.
- Example: BUCK1, BUCK2, BUCK9
Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
as per the datasheet of device.
Optional properties of the nodes under "regulators" sub-node:
- op_mode: describes the different operating modes of the LDO's with
power mode change in SOC. The different possible values are,
0 - always off mode
1 - on in normal mode
2 - low power mode
3 - suspend mode
- s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
GPIO controlling this regulator
(enable/disable); This is valid only
for buck9.
Example:
s5m8767_pmic@66 {
compatible = "samsung,s5m8767-pmic";
reg = <0x66>;
s5m8767,pmic-buck2-uses-gpio-dvs;
s5m8767,pmic-buck3-uses-gpio-dvs;
s5m8767,pmic-buck4-uses-gpio-dvs;
s5m8767,pmic-buck-default-dvs-idx = <0>;
s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
<&gpx0 1 0>, /* DVS2 */
<&gpx0 2 0>; /* DVS3 */
s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
<&gpx2 4 0>, /* SET2 */
<&gpx2 5 0>; /* SET3 */
s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
<1250000>, <1200000>,
<1150000>, <1100000>,
<1000000>, <950000>;
s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
<1100000>, <1100000>,
<1000000>, <1000000>,
<1000000>, <1000000>;
s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>;
regulators {
ldo1_reg: LDO1 {
regulator-name = "VDD_ABB_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
op_mode = <1>; /* Normal Mode */
};
ldo2_reg: LDO2 {
regulator-name = "VDD_ALIVE_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
buck1_reg: BUCK1 {
regulator-name = "VDD_MIF_1.2V";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
vemmc_reg: BUCK9 {
regulator-name = "VMEM_VDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
op_mode = <3>; /* Standby Mode */
s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
};
};
};
|
