Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 91 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
new file mode 100644
index 000000000..f591ab782
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
@@ -0,0 +1,91 @@
+APM X-Gene SoC Ethernet nodes
+
+Ethernet nodes are defined to describe on-chip ethernet interfaces in
+APM X-Gene SoC.
+
+Required properties for all the ethernet interfaces:
+- compatible: Should state binding information from the following list,
+  - "apm,xgene-enet":    RGMII based 1G interface
+  - "apm,xgene1-sgenet": SGMII based 1G interface
+  - "apm,xgene1-xgenet": XFI based 10G interface
+- reg: Address and length of the register set for the device. It contains the
+  information of registers in the same order as described by reg-names
+- reg-names: Should contain the register set names
+  - "enet_csr": Ethernet control and status register address space
+  - "ring_csr": Descriptor ring control and status register address space
+  - "ring_cmd": Descriptor ring command register address space
+- interrupts: Two interrupt specifiers can be specified.
+  - First is the Rx interrupt.  This irq is mandatory.
+  - Second is the Tx completion interrupt.
+    This is supported only on SGMII based 1GbE and 10GbE interfaces.
+- channel: Ethernet to CPU, start channel (prefetch buffer) number
+  - Must map to the first irq and irqs must be sequential
+- port-id: Port number (0 or 1)
+- clocks: Reference to the clock entry.
+- local-mac-address: MAC address assigned to this device
+- phy-connection-type: Interface type between ethernet device and PHY device
+
+Required properties for ethernet interfaces that have external PHY:
+- phy-handle: Reference to a PHY node connected to this device
+
+- mdio: Device tree subnode with the following required properties:
+  - compatible: Must be "apm,xgene-mdio".
+  - #address-cells: Must be <1>.
+  - #size-cells: Must be <0>.
+
+  For the phy on the mdio bus, there must be a node with the following fields:
+  - compatible: PHY identifier.  Please refer ./phy.txt for the format.
+  - reg: The ID number for the phy.
+
+Optional properties:
+- status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok".
+- tx-delay: Delay value for RGMII bridge TX clock.
+	    Valid values are between 0 to 7, that maps to
+	    417, 717, 1020, 1321, 1611, 1913, 2215, 2514 ps
+	    Default value is 4, which corresponds to 1611 ps
+- rx-delay: Delay value for RGMII bridge RX clock.
+	    Valid values are between 0 to 7, that maps to
+	    273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps
+	    Default value is 2, which corresponds to 899 ps
+- rxlos-gpios: Input gpio from SFP+ module to indicate availability of
+	       incoming signal.
+
+
+Example:
+	menetclk: menetclk {
+		compatible = "apm,xgene-device-clock";
+		clock-output-names = "menetclk";
+		status = "ok";
+	};
+
+	menet: ethernet@17020000 {
+		compatible = "apm,xgene-enet";
+		status = "disabled";
+		reg = <0x0 0x17020000 0x0 0xd100>,
+		      <0x0 0x17030000 0x0 0x400>,
+		      <0x0 0x10000000 0x0 0x200>;
+		reg-names = "enet_csr", "ring_csr", "ring_cmd";
+		interrupts = <0x0 0x3c 0x4>;
+		port-id = <0>;
+		clocks = <&menetclk 0>;
+		local-mac-address = [00 01 73 00 00 01];
+		phy-connection-type = "rgmii";
+		phy-handle = <&menetphy>;
+		mdio {
+			compatible = "apm,xgene-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			menetphy: menetphy@3 {
+				compatible = "ethernet-phy-id001c.c915";
+				reg = <0x3>;
+			};
+
+		};
+	};
+
+/* Board-specific peripheral configurations */
+&menet {
+	tx-delay = <4>;
+	rx-delay = <2>;
+        status = "ok";
+};