Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 147 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
new file mode 100644
index 000000000..c666afb12
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+	model = "I2SE Duckbill";
+	compatible = "i2se,duckbill", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	apb@80000000 {
+		apbh@80000000 {
+			ssp0: spi@80010000 {
+				compatible = "fsl,imx28-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc0_4bit_pins_a
+					&mmc0_cd_cfg &mmc0_sck_cfg>;
+				bus-width = <4>;
+				vmmc-supply = <&reg_3p3v>;
+				status = "okay";
+			};
+
+			ssp2: spi@80014000 {
+				compatible = "fsl,imx28-spi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi2_pins_a>;
+				status = "okay";
+			};
+
+			pinctrl@80018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&hog_pins_a>;
+
+				hog_pins_a: hog@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
+				mac0_phy_reset_pin: mac0-phy-reset@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
+				led_pins: leds@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_AUART1_RX__GPIO_3_4
+						MX28_PAD_AUART1_TX__GPIO_3_5
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+			};
+		};
+
+		apbx@80040000 {
+			lradc@80050000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@80058000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins_a>;
+				status = "okay";
+			};
+
+			auart0: serial@8006a000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&auart0_2pins_a>;
+				status = "okay";
+			};
+
+			duart: serial@80074000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&duart_pins_a>;
+				status = "okay";
+			};
+
+			usbphy0: usbphy@8007c000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb0: usb@80080000 {
+			status = "okay";
+			dr_mode = "peripheral";
+		};
+
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+			phy-supply = <&reg_3p3v>;
+			phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+			phy-reset-duration = <25>;
+			status = "okay";
+		};
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		status-red {
+			label = "duckbill:red:status";
+			gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		status-green {
+			label = "duckbill:green:status";
+			gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};