Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 427 insertions, 0 deletions

diff --git a/drivers/edac/r82600_edac.c b/drivers/edac/r82600_edac.c
new file mode 100644
index 000000000..d0aef83dc
--- /dev/null
+++ b/drivers/edac/r82600_edac.c
@@ -0,0 +1,427 @@
+/*
+ * Radisys 82600 Embedded chipset Memory Controller kernel module
+ * (C) 2005 EADS Astrium
+ * This file may be distributed under the terms of the
+ * GNU General Public License.
+ *
+ * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
+ * Harbaugh, Dan Hollis <goemon at anime dot net> and others.
+ *
+ * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
+ *
+ * Written with reference to 82600 High Integration Dual PCI System
+ * Controller Data Book:
+ * www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
+ * references to this document given in []
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/edac.h>
+#include "edac_module.h"
+
+#define EDAC_MOD_STR	"r82600_edac"
+
+#define r82600_printk(level, fmt, arg...) \
+	edac_printk(level, "r82600", fmt, ##arg)
+
+#define r82600_mc_printk(mci, level, fmt, arg...) \
+	edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)
+
+/* Radisys say "The 82600 integrates a main memory SDRAM controller that
+ * supports up to four banks of memory. The four banks can support a mix of
+ * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
+ * each of which can be any size from 16MB to 512MB. Both registered (control
+ * signals buffered) and unbuffered DIMM types are supported. Mixing of
+ * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
+ * is not allowed. The 82600 SDRAM interface operates at the same frequency as
+ * the CPU bus, 66MHz, 100MHz or 133MHz."
+ */
+
+#define R82600_NR_CSROWS 4
+#define R82600_NR_CHANS  1
+#define R82600_NR_DIMMS  4
+
+#define R82600_BRIDGE_ID  0x8200
+
+/* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
+#define R82600_DRAMC	0x57	/* Various SDRAM related control bits
+				 * all bits are R/W
+				 *
+				 * 7    SDRAM ISA Hole Enable
+				 * 6    Flash Page Mode Enable
+				 * 5    ECC Enable: 1=ECC 0=noECC
+				 * 4    DRAM DIMM Type: 1=
+				 * 3    BIOS Alias Disable
+				 * 2    SDRAM BIOS Flash Write Enable
+				 * 1:0  SDRAM Refresh Rate: 00=Disabled
+				 *          01=7.8usec (256Mbit SDRAMs)
+				 *          10=15.6us 11=125usec
+				 */
+
+#define R82600_SDRAMC	0x76	/* "SDRAM Control Register"
+				 * More SDRAM related control bits
+				 * all bits are R/W
+				 *
+				 * 15:8 Reserved.
+				 *
+				 * 7:5  Special SDRAM Mode Select
+				 *
+				 * 4    Force ECC
+				 *
+				 *        1=Drive ECC bits to 0 during
+				 *          write cycles (i.e. ECC test mode)
+				 *
+				 *        0=Normal ECC functioning
+				 *
+				 * 3    Enhanced Paging Enable
+				 *
+				 * 2    CAS# Latency 0=3clks 1=2clks
+				 *
+				 * 1    RAS# to CAS# Delay 0=3 1=2
+				 *
+				 * 0    RAS# Precharge     0=3 1=2
+				 */
+
+#define R82600_EAP	0x80	/* ECC Error Address Pointer Register
+				 *
+				 * 31    Disable Hardware Scrubbing (RW)
+				 *        0=Scrub on corrected read
+				 *        1=Don't scrub on corrected read
+				 *
+				 * 30:12 Error Address Pointer (RO)
+				 *        Upper 19 bits of error address
+				 *
+				 * 11:4  Syndrome Bits (RO)
+				 *
+				 * 3     BSERR# on multibit error (RW)
+				 *        1=enable 0=disable
+				 *
+				 * 2     NMI on Single Bit Eror (RW)
+				 *        1=NMI triggered by SBE n.b. other
+				 *          prerequeists
+				 *        0=NMI not triggered
+				 *
+				 * 1     MBE (R/WC)
+				 *        read 1=MBE at EAP (see above)
+				 *        read 0=no MBE, or SBE occurred first
+				 *        write 1=Clear MBE status (must also
+				 *          clear SBE)
+				 *        write 0=NOP
+				 *
+				 * 1     SBE (R/WC)
+				 *        read 1=SBE at EAP (see above)
+				 *        read 0=no SBE, or MBE occurred first
+				 *        write 1=Clear SBE status (must also
+				 *          clear MBE)
+				 *        write 0=NOP
+				 */
+
+#define R82600_DRBA	0x60	/* + 0x60..0x63 SDRAM Row Boundary Address
+				 *  Registers
+				 *
+				 * 7:0  Address lines 30:24 - upper limit of
+				 * each row [p57]
+				 */
+
+struct r82600_error_info {
+	u32 eapr;
+};
+
+static bool disable_hardware_scrub;
+
+static struct edac_pci_ctl_info *r82600_pci;
+
+static void r82600_get_error_info(struct mem_ctl_info *mci,
+				struct r82600_error_info *info)
+{
+	struct pci_dev *pdev;
+
+	pdev = to_pci_dev(mci->pdev);
+	pci_read_config_dword(pdev, R82600_EAP, &info->eapr);
+
+	if (info->eapr & BIT(0))
+		/* Clear error to allow next error to be reported [p.62] */
+		pci_write_bits32(pdev, R82600_EAP,
+				 ((u32) BIT(0) & (u32) BIT(1)),
+				 ((u32) BIT(0) & (u32) BIT(1)));
+
+	if (info->eapr & BIT(1))
+		/* Clear error to allow next error to be reported [p.62] */
+		pci_write_bits32(pdev, R82600_EAP,
+				 ((u32) BIT(0) & (u32) BIT(1)),
+				 ((u32) BIT(0) & (u32) BIT(1)));
+}
+
+static int r82600_process_error_info(struct mem_ctl_info *mci,
+				struct r82600_error_info *info,
+				int handle_errors)
+{
+	int error_found;
+	u32 eapaddr, page;
+	u32 syndrome;
+
+	error_found = 0;
+
+	/* bits 30:12 store the upper 19 bits of the 32 bit error address */
+	eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
+	/* Syndrome in bits 11:4 [p.62]       */
+	syndrome = (info->eapr >> 4) & 0xFF;
+
+	/* the R82600 reports at less than page *
+	 * granularity (upper 19 bits only)     */
+	page = eapaddr >> PAGE_SHIFT;
+
+	if (info->eapr & BIT(0)) {	/* CE? */
+		error_found = 1;
+
+		if (handle_errors)
+			edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci, 1,
+					     page, 0, syndrome,
+					     edac_mc_find_csrow_by_page(mci, page),
+					     0, -1,
+					     mci->ctl_name, "");
+	}
+
+	if (info->eapr & BIT(1)) {	/* UE? */
+		error_found = 1;
+
+		if (handle_errors)
+			/* 82600 doesn't give enough info */
+			edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci, 1,
+					     page, 0, 0,
+					     edac_mc_find_csrow_by_page(mci, page),
+					     0, -1,
+					     mci->ctl_name, "");
+	}
+
+	return error_found;
+}
+
+static void r82600_check(struct mem_ctl_info *mci)
+{
+	struct r82600_error_info info;
+
+	r82600_get_error_info(mci, &info);
+	r82600_process_error_info(mci, &info, 1);
+}
+
+static inline int ecc_enabled(u8 dramcr)
+{
+	return dramcr & BIT(5);
+}
+
+static void r82600_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev,
+			u8 dramcr)
+{
+	struct csrow_info *csrow;
+	struct dimm_info *dimm;
+	int index;
+	u8 drbar;		/* SDRAM Row Boundary Address Register */
+	u32 row_high_limit, row_high_limit_last;
+	u32 reg_sdram, ecc_on, row_base;
+
+	ecc_on = ecc_enabled(dramcr);
+	reg_sdram = dramcr & BIT(4);
+	row_high_limit_last = 0;
+
+	for (index = 0; index < mci->nr_csrows; index++) {
+		csrow = mci->csrows[index];
+		dimm = csrow->channels[0]->dimm;
+
+		/* find the DRAM Chip Select Base address and mask */
+		pci_read_config_byte(pdev, R82600_DRBA + index, &drbar);
+
+		edac_dbg(1, "Row=%d DRBA = %#0x\n", index, drbar);
+
+		row_high_limit = ((u32) drbar << 24);
+/*		row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */
+
+		edac_dbg(1, "Row=%d, Boundary Address=%#0x, Last = %#0x\n",
+			 index, row_high_limit, row_high_limit_last);
+
+		/* Empty row [p.57] */
+		if (row_high_limit == row_high_limit_last)
+			continue;
+
+		row_base = row_high_limit_last;
+
+		csrow->first_page = row_base >> PAGE_SHIFT;
+		csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;
+
+		dimm->nr_pages = csrow->last_page - csrow->first_page + 1;
+		/* Error address is top 19 bits - so granularity is      *
+		 * 14 bits                                               */
+		dimm->grain = 1 << 14;
+		dimm->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
+		/* FIXME - check that this is unknowable with this chipset */
+		dimm->dtype = DEV_UNKNOWN;
+
+		/* Mode is global on 82600 */
+		dimm->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
+		row_high_limit_last = row_high_limit;
+	}
+}
+
+static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
+{
+	struct mem_ctl_info *mci;
+	struct edac_mc_layer layers[2];
+	u8 dramcr;
+	u32 eapr;
+	u32 scrub_disabled;
+	u32 sdram_refresh_rate;
+	struct r82600_error_info discard;
+
+	edac_dbg(0, "\n");
+	pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
+	pci_read_config_dword(pdev, R82600_EAP, &eapr);
+	scrub_disabled = eapr & BIT(31);
+	sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
+	edac_dbg(2, "sdram refresh rate = %#0x\n", sdram_refresh_rate);
+	edac_dbg(2, "DRAMC register = %#0x\n", dramcr);
+	layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
+	layers[0].size = R82600_NR_CSROWS;
+	layers[0].is_virt_csrow = true;
+	layers[1].type = EDAC_MC_LAYER_CHANNEL;
+	layers[1].size = R82600_NR_CHANS;
+	layers[1].is_virt_csrow = false;
+	mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers, 0);
+	if (mci == NULL)
+		return -ENOMEM;
+
+	edac_dbg(0, "mci = %p\n", mci);
+	mci->pdev = &pdev->dev;
+	mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
+	mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
+	/* FIXME try to work out if the chip leads have been used for COM2
+	 * instead on this board? [MA6?] MAYBE:
+	 */
+
+	/* On the R82600, the pins for memory bits 72:65 - i.e. the   *
+	 * EC bits are shared with the pins for COM2 (!), so if COM2  *
+	 * is enabled, we assume COM2 is wired up, and thus no EDAC   *
+	 * is possible.                                               */
+	mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
+
+	if (ecc_enabled(dramcr)) {
+		if (scrub_disabled)
+			edac_dbg(3, "mci = %p - Scrubbing disabled! EAP: %#0x\n",
+				 mci, eapr);
+	} else
+		mci->edac_cap = EDAC_FLAG_NONE;
+
+	mci->mod_name = EDAC_MOD_STR;
+	mci->ctl_name = "R82600";
+	mci->dev_name = pci_name(pdev);
+	mci->edac_check = r82600_check;
+	mci->ctl_page_to_phys = NULL;
+	r82600_init_csrows(mci, pdev, dramcr);
+	r82600_get_error_info(mci, &discard);	/* clear counters */
+
+	/* Here we assume that we will never see multiple instances of this
+	 * type of memory controller.  The ID is therefore hardcoded to 0.
+	 */
+	if (edac_mc_add_mc(mci)) {
+		edac_dbg(3, "failed edac_mc_add_mc()\n");
+		goto fail;
+	}
+
+	/* get this far and it's successful */
+
+	if (disable_hardware_scrub) {
+		edac_dbg(3, "Disabling Hardware Scrub (scrub on error)\n");
+		pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31));
+	}
+
+	/* allocating generic PCI control info */
+	r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
+	if (!r82600_pci) {
+		printk(KERN_WARNING
+			"%s(): Unable to create PCI control\n",
+			__func__);
+		printk(KERN_WARNING
+			"%s(): PCI error report via EDAC not setup\n",
+			__func__);
+	}
+
+	edac_dbg(3, "success\n");
+	return 0;
+
+fail:
+	edac_mc_free(mci);
+	return -ENODEV;
+}
+
+/* returns count (>= 0), or negative on error */
+static int r82600_init_one(struct pci_dev *pdev,
+			   const struct pci_device_id *ent)
+{
+	edac_dbg(0, "\n");
+
+	/* don't need to call pci_enable_device() */
+	return r82600_probe1(pdev, ent->driver_data);
+}
+
+static void r82600_remove_one(struct pci_dev *pdev)
+{
+	struct mem_ctl_info *mci;
+
+	edac_dbg(0, "\n");
+
+	if (r82600_pci)
+		edac_pci_release_generic_ctl(r82600_pci);
+
+	if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
+		return;
+
+	edac_mc_free(mci);
+}
+
+static const struct pci_device_id r82600_pci_tbl[] = {
+	{
+	 PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)
+	 },
+	{
+	 0,
+	 }			/* 0 terminated list. */
+};
+
+MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);
+
+static struct pci_driver r82600_driver = {
+	.name = EDAC_MOD_STR,
+	.probe = r82600_init_one,
+	.remove = r82600_remove_one,
+	.id_table = r82600_pci_tbl,
+};
+
+static int __init r82600_init(void)
+{
+       /* Ensure that the OPSTATE is set correctly for POLL or NMI */
+       opstate_init();
+
+	return pci_register_driver(&r82600_driver);
+}
+
+static void __exit r82600_exit(void)
+{
+	pci_unregister_driver(&r82600_driver);
+}
+
+module_init(r82600_init);
+module_exit(r82600_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
+		"on behalf of EADS Astrium");
+MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");
+
+module_param(disable_hardware_scrub, bool, 0644);
+MODULE_PARM_DESC(disable_hardware_scrub,
+		 "If set, disable the chipset's automatic scrub for CEs");
+
+module_param(edac_op_state, int, 0444);
+MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");