Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 484 insertions, 0 deletions

diff --git a/drivers/input/touchscreen/bu21029_ts.c b/drivers/input/touchscreen/bu21029_ts.c
new file mode 100644
index 000000000..392950aa7
--- /dev/null
+++ b/drivers/input/touchscreen/bu21029_ts.c
@@ -0,0 +1,484 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rohm BU21029 touchscreen controller driver
+ *
+ * Copyright (C) 2015-2018 Bosch Sicherheitssysteme GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/touchscreen.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+#include <linux/timer.h>
+
+/*
+ * HW_ID1 Register (PAGE=0, ADDR=0x0E, Reset value=0x02, Read only)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |                                 HW_IDH                                |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * HW_ID2 Register (PAGE=0, ADDR=0x0F, Reset value=0x29, Read only)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |                                 HW_IDL                                |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * HW_IDH: high 8bits of IC's ID
+ * HW_IDL: low  8bits of IC's ID
+ */
+#define BU21029_HWID_REG	(0x0E << 3)
+#define SUPPORTED_HWID		0x0229
+
+/*
+ * CFR0 Register (PAGE=0, ADDR=0x00, Reset value=0x20)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   0    |   0    |  CALIB |  INTRM |   0    |   0    |   0    |   0    |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * CALIB: 0 = not to use calibration result (*)
+ *        1 = use calibration result
+ * INTRM: 0 = INT output depend on "pen down" (*)
+ *        1 = INT output always "0"
+ */
+#define BU21029_CFR0_REG	(0x00 << 3)
+#define CFR0_VALUE		0x00
+
+/*
+ * CFR1 Register (PAGE=0, ADDR=0x01, Reset value=0xA6)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |  MAV   |         AVE[2:0]         |   0    |         SMPL[2:0]        |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * MAV:  0 = median average filter off
+ *       1 = median average filter on (*)
+ * AVE:  AVE+1 = number of average samples for MAV,
+ *               if AVE>SMPL, then AVE=SMPL (=3)
+ * SMPL: SMPL+1 = number of conversion samples for MAV (=7)
+ */
+#define BU21029_CFR1_REG	(0x01 << 3)
+#define CFR1_VALUE		0xA6
+
+/*
+ * CFR2 Register (PAGE=0, ADDR=0x02, Reset value=0x04)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |          INTVL_TIME[3:0]          |          TIME_ST_ADC[3:0]         |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * INTVL_TIME: waiting time between completion of conversion
+ *             and start of next conversion, only usable in
+ *             autoscan mode (=20.480ms)
+ * TIME_ST_ADC: waiting time between application of voltage
+ *              to panel and start of A/D conversion (=100us)
+ */
+#define BU21029_CFR2_REG	(0x02 << 3)
+#define CFR2_VALUE		0xC9
+
+/*
+ * CFR3 Register (PAGE=0, ADDR=0x0B, Reset value=0x72)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |  RM8   | STRETCH|  PU90K |  DUAL  |           PIDAC_OFS[3:0]          |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * RM8: 0 = coordinate resolution is 12bit (*)
+ *      1 = coordinate resolution is 8bit
+ * STRETCH: 0 = SCL_STRETCH function off
+ *          1 = SCL_STRETCH function on (*)
+ * PU90K: 0 = internal pull-up resistance for touch detection is ~50kohms (*)
+ *        1 = internal pull-up resistance for touch detection is ~90kohms
+ * DUAL: 0 = dual touch detection off (*)
+ *       1 = dual touch detection on
+ * PIDAC_OFS: dual touch detection circuit adjustment, it is not necessary
+ *            to change this from initial value
+ */
+#define BU21029_CFR3_REG	(0x0B << 3)
+#define CFR3_VALUE		0x42
+
+/*
+ * LDO Register (PAGE=0, ADDR=0x0C, Reset value=0x00)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   0    |         PVDD[2:0]        |   0    |         AVDD[2:0]        |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * PVDD: output voltage of panel output regulator (=2.000V)
+ * AVDD: output voltage of analog circuit regulator (=2.000V)
+ */
+#define BU21029_LDO_REG		(0x0C << 3)
+#define LDO_VALUE		0x77
+
+/*
+ * Serial Interface Command Byte 1 (CID=1)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   1    |                 CF                |  CMSK  |  PDM   |  STP   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * CF: conversion function, see table 3 in datasheet p6 (=0000, automatic scan)
+ * CMSK: 0 = executes convert function (*)
+ *       1 = reads the convert result
+ * PDM: 0 = power down after convert function stops (*)
+ *      1 = keep power on after convert function stops
+ * STP: 1 = abort current conversion and power down, set to "0" automatically
+ */
+#define BU21029_AUTOSCAN	0x80
+
+/*
+ * The timeout value needs to be larger than INTVL_TIME + tConv4 (sample and
+ * conversion time), where tConv4 is calculated by formula:
+ * tPON + tDLY1 + (tTIME_ST_ADC + (tADC * tSMPL) * 2 + tDLY2) * 3
+ * see figure 8 in datasheet p15 for details of each field.
+ */
+#define PEN_UP_TIMEOUT_MS	50
+
+#define STOP_DELAY_MIN_US	50
+#define STOP_DELAY_MAX_US	1000
+#define START_DELAY_MS		2
+#define BUF_LEN			8
+#define SCALE_12BIT		(1 << 12)
+#define MAX_12BIT		((1 << 12) - 1)
+#define DRIVER_NAME		"bu21029"
+
+struct bu21029_ts_data {
+	struct i2c_client		*client;
+	struct input_dev		*in_dev;
+	struct timer_list		timer;
+	struct regulator		*vdd;
+	struct gpio_desc		*reset_gpios;
+	u32				x_plate_ohms;
+	struct touchscreen_properties	prop;
+};
+
+static void bu21029_touch_report(struct bu21029_ts_data *bu21029, const u8 *buf)
+{
+	u16 x, y, z1, z2;
+	u32 rz;
+	s32 max_pressure = input_abs_get_max(bu21029->in_dev, ABS_PRESSURE);
+
+	/*
+	 * compose upper 8 and lower 4 bits into a 12bit value:
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 * |            ByteH              |            ByteL              |
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 * |b07|b06|b05|b04|b03|b02|b01|b00|b07|b06|b05|b04|b03|b02|b01|b00|
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 * |v11|v10|v09|v08|v07|v06|v05|v04|v03|v02|v01|v00| 0 | 0 | 0 | 0 |
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 */
+	x  = (buf[0] << 4) | (buf[1] >> 4);
+	y  = (buf[2] << 4) | (buf[3] >> 4);
+	z1 = (buf[4] << 4) | (buf[5] >> 4);
+	z2 = (buf[6] << 4) | (buf[7] >> 4);
+
+	if (z1 && z2) {
+		/*
+		 * calculate Rz (pressure resistance value) by equation:
+		 * Rz = Rx * (x/Q) * ((z2/z1) - 1), where
+		 * Rx is x-plate resistance,
+		 * Q  is the touch screen resolution (8bit = 256, 12bit = 4096)
+		 * x, z1, z2 are the measured positions.
+		 */
+		rz  = z2 - z1;
+		rz *= x;
+		rz *= bu21029->x_plate_ohms;
+		rz /= z1;
+		rz  = DIV_ROUND_CLOSEST(rz, SCALE_12BIT);
+		if (rz <= max_pressure) {
+			touchscreen_report_pos(bu21029->in_dev, &bu21029->prop,
+					       x, y, false);
+			input_report_abs(bu21029->in_dev, ABS_PRESSURE,
+					 max_pressure - rz);
+			input_report_key(bu21029->in_dev, BTN_TOUCH, 1);
+			input_sync(bu21029->in_dev);
+		}
+	}
+}
+
+static void bu21029_touch_release(struct timer_list *t)
+{
+	struct bu21029_ts_data *bu21029 = from_timer(bu21029, t, timer);
+
+	input_report_abs(bu21029->in_dev, ABS_PRESSURE, 0);
+	input_report_key(bu21029->in_dev, BTN_TOUCH, 0);
+	input_sync(bu21029->in_dev);
+}
+
+static irqreturn_t bu21029_touch_soft_irq(int irq, void *data)
+{
+	struct bu21029_ts_data *bu21029 = data;
+	u8 buf[BUF_LEN];
+	int error;
+
+	/*
+	 * Read touch data and deassert interrupt (will assert again after
+	 * INTVL_TIME + tConv4 for continuous touch)
+	 */
+	error = i2c_smbus_read_i2c_block_data(bu21029->client, BU21029_AUTOSCAN,
+					      sizeof(buf), buf);
+	if (error < 0)
+		goto out;
+
+	bu21029_touch_report(bu21029, buf);
+
+	/* reset timer for pen up detection */
+	mod_timer(&bu21029->timer,
+		  jiffies + msecs_to_jiffies(PEN_UP_TIMEOUT_MS));
+
+out:
+	return IRQ_HANDLED;
+}
+
+static void bu21029_put_chip_in_reset(struct bu21029_ts_data *bu21029)
+{
+	if (bu21029->reset_gpios) {
+		gpiod_set_value_cansleep(bu21029->reset_gpios, 1);
+		usleep_range(STOP_DELAY_MIN_US, STOP_DELAY_MAX_US);
+	}
+}
+
+static int bu21029_start_chip(struct input_dev *dev)
+{
+	struct bu21029_ts_data *bu21029 = input_get_drvdata(dev);
+	struct i2c_client *i2c = bu21029->client;
+	struct {
+		u8 reg;
+		u8 value;
+	} init_table[] = {
+		{BU21029_CFR0_REG, CFR0_VALUE},
+		{BU21029_CFR1_REG, CFR1_VALUE},
+		{BU21029_CFR2_REG, CFR2_VALUE},
+		{BU21029_CFR3_REG, CFR3_VALUE},
+		{BU21029_LDO_REG,  LDO_VALUE}
+	};
+	int error, i;
+	__be16 hwid;
+
+	error = regulator_enable(bu21029->vdd);
+	if (error) {
+		dev_err(&i2c->dev, "failed to power up chip: %d", error);
+		return error;
+	}
+
+	/* take chip out of reset */
+	if (bu21029->reset_gpios) {
+		gpiod_set_value_cansleep(bu21029->reset_gpios, 0);
+		msleep(START_DELAY_MS);
+	}
+
+	error = i2c_smbus_read_i2c_block_data(i2c, BU21029_HWID_REG,
+					      sizeof(hwid), (u8 *)&hwid);
+	if (error < 0) {
+		dev_err(&i2c->dev, "failed to read HW ID\n");
+		goto err_out;
+	}
+
+	if (be16_to_cpu(hwid) != SUPPORTED_HWID) {
+		dev_err(&i2c->dev,
+			"unsupported HW ID 0x%x\n", be16_to_cpu(hwid));
+		error = -ENODEV;
+		goto err_out;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(init_table); ++i) {
+		error = i2c_smbus_write_byte_data(i2c,
+						  init_table[i].reg,
+						  init_table[i].value);
+		if (error < 0) {
+			dev_err(&i2c->dev,
+				"failed to write %#02x to register %#02x: %d\n",
+				init_table[i].value, init_table[i].reg,
+				error);
+			goto err_out;
+		}
+	}
+
+	error = i2c_smbus_write_byte(i2c, BU21029_AUTOSCAN);
+	if (error < 0) {
+		dev_err(&i2c->dev, "failed to start autoscan\n");
+		goto err_out;
+	}
+
+	enable_irq(bu21029->client->irq);
+	return 0;
+
+err_out:
+	bu21029_put_chip_in_reset(bu21029);
+	regulator_disable(bu21029->vdd);
+	return error;
+}
+
+static void bu21029_stop_chip(struct input_dev *dev)
+{
+	struct bu21029_ts_data *bu21029 = input_get_drvdata(dev);
+
+	disable_irq(bu21029->client->irq);
+	del_timer_sync(&bu21029->timer);
+
+	bu21029_put_chip_in_reset(bu21029);
+	regulator_disable(bu21029->vdd);
+}
+
+static int bu21029_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct bu21029_ts_data *bu21029;
+	struct input_dev *in_dev;
+	int error;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_WRITE_BYTE |
+				     I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+		dev_err(&client->dev,
+			"i2c functionality support is not sufficient\n");
+		return -EIO;
+	}
+
+	bu21029 = devm_kzalloc(&client->dev, sizeof(*bu21029), GFP_KERNEL);
+	if (!bu21029)
+		return -ENOMEM;
+
+	error = device_property_read_u32(&client->dev, "rohm,x-plate-ohms",
+					 &bu21029->x_plate_ohms);
+	if (error) {
+		dev_err(&client->dev,
+			"invalid 'x-plate-ohms' supplied: %d\n", error);
+		return error;
+	}
+
+	bu21029->vdd = devm_regulator_get(&client->dev, "vdd");
+	if (IS_ERR(bu21029->vdd)) {
+		error = PTR_ERR(bu21029->vdd);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"failed to acquire 'vdd' supply: %d\n", error);
+		return error;
+	}
+
+	bu21029->reset_gpios = devm_gpiod_get_optional(&client->dev,
+						       "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(bu21029->reset_gpios)) {
+		error = PTR_ERR(bu21029->reset_gpios);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"failed to acquire 'reset' gpio: %d\n", error);
+		return error;
+	}
+
+	in_dev = devm_input_allocate_device(&client->dev);
+	if (!in_dev) {
+		dev_err(&client->dev, "unable to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	bu21029->client = client;
+	bu21029->in_dev = in_dev;
+	timer_setup(&bu21029->timer, bu21029_touch_release, 0);
+
+	in_dev->name		= DRIVER_NAME;
+	in_dev->id.bustype	= BUS_I2C;
+	in_dev->open		= bu21029_start_chip;
+	in_dev->close		= bu21029_stop_chip;
+
+	input_set_capability(in_dev, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(in_dev, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(in_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(in_dev, ABS_PRESSURE, 0, MAX_12BIT, 0, 0);
+	touchscreen_parse_properties(in_dev, false, &bu21029->prop);
+
+	input_set_drvdata(in_dev, bu21029);
+
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, bu21029_touch_soft_irq,
+					  IRQF_ONESHOT | IRQF_NO_AUTOEN,
+					  DRIVER_NAME, bu21029);
+	if (error) {
+		dev_err(&client->dev,
+			"unable to request touch irq: %d\n", error);
+		return error;
+	}
+
+	error = input_register_device(in_dev);
+	if (error) {
+		dev_err(&client->dev,
+			"unable to register input device: %d\n", error);
+		return error;
+	}
+
+	i2c_set_clientdata(client, bu21029);
+
+	return 0;
+}
+
+static int __maybe_unused bu21029_suspend(struct device *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct bu21029_ts_data *bu21029 = i2c_get_clientdata(i2c);
+
+	if (!device_may_wakeup(dev)) {
+		mutex_lock(&bu21029->in_dev->mutex);
+		if (input_device_enabled(bu21029->in_dev))
+			bu21029_stop_chip(bu21029->in_dev);
+		mutex_unlock(&bu21029->in_dev->mutex);
+	}
+
+	return 0;
+}
+
+static int __maybe_unused bu21029_resume(struct device *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct bu21029_ts_data *bu21029 = i2c_get_clientdata(i2c);
+
+	if (!device_may_wakeup(dev)) {
+		mutex_lock(&bu21029->in_dev->mutex);
+		if (input_device_enabled(bu21029->in_dev))
+			bu21029_start_chip(bu21029->in_dev);
+		mutex_unlock(&bu21029->in_dev->mutex);
+	}
+
+	return 0;
+}
+static SIMPLE_DEV_PM_OPS(bu21029_pm_ops, bu21029_suspend, bu21029_resume);
+
+static const struct i2c_device_id bu21029_ids[] = {
+	{ DRIVER_NAME, 0 },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, bu21029_ids);
+
+#ifdef CONFIG_OF
+static const struct of_device_id bu21029_of_ids[] = {
+	{ .compatible = "rohm,bu21029" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, bu21029_of_ids);
+#endif
+
+static struct i2c_driver bu21029_driver = {
+	.driver	= {
+		.name		= DRIVER_NAME,
+		.of_match_table	= of_match_ptr(bu21029_of_ids),
+		.pm		= &bu21029_pm_ops,
+	},
+	.id_table	= bu21029_ids,
+	.probe		= bu21029_probe,
+};
+module_i2c_driver(bu21029_driver);
+
+MODULE_AUTHOR("Zhu Yi <yi.zhu5@cn.bosch.com>");
+MODULE_DESCRIPTION("Rohm BU21029 touchscreen controller driver");
+MODULE_LICENSE("GPL v2");