Merging upstream version 6.1.85.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

7 files changed, 44 insertions, 22 deletions

diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index dca1abe36..55451ff84 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -714,6 +714,7 @@ static void exar_pci_remove(struct pci_dev *pcidev)
 	for (i = 0; i < priv->nr; i++)
 		serial8250_unregister_port(priv->line[i]);
 
+	/* Ensure that every init quirk is properly torn down */
 	if (priv->board->exit)
 		priv->board->exit(pcidev);
 }
@@ -728,10 +729,6 @@ static int __maybe_unused exar_suspend(struct device *dev)
 		if (priv->line[i] >= 0)
 			serial8250_suspend_port(priv->line[i]);
 
-	/* Ensure that every init quirk is properly torn down */
-	if (priv->board->exit)
-		priv->board->exit(pcidev);
-
 	return 0;
 }
 
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 8efe31448..c744feabd 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1377,9 +1377,6 @@ static void autoconfig_irq(struct uart_8250_port *up)
 		inb_p(ICP);
 	}
 
-	if (uart_console(port))
-		console_lock();
-
 	/* forget possible initially masked and pending IRQ */
 	probe_irq_off(probe_irq_on());
 	save_mcr = serial8250_in_MCR(up);
@@ -1410,9 +1407,6 @@ static void autoconfig_irq(struct uart_8250_port *up)
 	if (port->flags & UPF_FOURPORT)
 		outb_p(save_ICP, ICP);
 
-	if (uart_console(port))
-		console_unlock();
-
 	port->irq = (irq > 0) ? irq : 0;
 }
 
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index c5a9b89c4..f94c78263 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -2213,9 +2213,12 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	lpuart32_write(&sport->port, bd, UARTBAUD);
 	lpuart32_serial_setbrg(sport, baud);
-	lpuart32_write(&sport->port, modem, UARTMODIR);
-	lpuart32_write(&sport->port, ctrl, UARTCTRL);
+	/* disable CTS before enabling UARTCTRL_TE to avoid pending idle preamble */
+	lpuart32_write(&sport->port, modem & ~UARTMODIR_TXCTSE, UARTMODIR);
 	/* restore control register */
+	lpuart32_write(&sport->port, ctrl, UARTCTRL);
+	/* re-enable the CTS if needed */
+	lpuart32_write(&sport->port, modem, UARTMODIR);
 
 	if ((ctrl & (UARTCTRL_PE | UARTCTRL_M)) == UARTCTRL_PE)
 		sport->is_cs7 = true;
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index f8962a3d4..573bf7e9b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -496,8 +496,7 @@ static void imx_uart_stop_tx(struct uart_port *port)
 	}
 }
 
-/* called with port.lock taken and irqs off */
-static void imx_uart_stop_rx(struct uart_port *port)
+static void imx_uart_stop_rx_with_loopback_ctrl(struct uart_port *port, bool loopback)
 {
 	struct imx_port *sport = (struct imx_port *)port;
 	u32 ucr1, ucr2, ucr4, uts;
@@ -519,7 +518,7 @@ static void imx_uart_stop_rx(struct uart_port *port)
 	/* See SER_RS485_ENABLED/UTS_LOOP comment in imx_uart_probe() */
 	if (port->rs485.flags & SER_RS485_ENABLED &&
 	    port->rs485.flags & SER_RS485_RTS_ON_SEND &&
-	    sport->have_rtscts && !sport->have_rtsgpio) {
+	    sport->have_rtscts && !sport->have_rtsgpio && loopback) {
 		uts = imx_uart_readl(sport, imx_uart_uts_reg(sport));
 		uts |= UTS_LOOP;
 		imx_uart_writel(sport, uts, imx_uart_uts_reg(sport));
@@ -532,6 +531,16 @@ static void imx_uart_stop_rx(struct uart_port *port)
 }
 
 /* called with port.lock taken and irqs off */
+static void imx_uart_stop_rx(struct uart_port *port)
+{
+	/*
+	 * Stop RX and enable loopback in order to make sure RS485 bus
+	 * is not blocked. Se comment in imx_uart_probe().
+	 */
+	imx_uart_stop_rx_with_loopback_ctrl(port, true);
+}
+
+/* called with port.lock taken and irqs off */
 static void imx_uart_enable_ms(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
@@ -719,8 +728,13 @@ static void imx_uart_start_tx(struct uart_port *port)
 				imx_uart_rts_inactive(sport, &ucr2);
 			imx_uart_writel(sport, ucr2, UCR2);
 
+			/*
+			 * Since we are about to transmit we can not stop RX
+			 * with loopback enabled because that will make our
+			 * transmitted data being just looped to RX.
+			 */
 			if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
-				imx_uart_stop_rx(port);
+				imx_uart_stop_rx_with_loopback_ctrl(port, false);
 
 			sport->tx_state = WAIT_AFTER_RTS;
 
diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
index 163a89f84..d409ef388 100644
--- a/drivers/tty/serial/max310x.c
+++ b/drivers/tty/serial/max310x.c
@@ -1459,7 +1459,7 @@ static int max310x_probe(struct device *dev, const struct max310x_devtype *devty
 	if (!ret)
 		return 0;
 
-	dev_err(dev, "Unable to reguest IRQ %i\n", irq);
+	dev_err(dev, "Unable to request IRQ %i\n", irq);
 
 out_uart:
 	for (i = 0; i < devtype->nr; i++) {
@@ -1633,13 +1633,16 @@ static unsigned short max310x_i2c_slave_addr(unsigned short addr,
 
 static int max310x_i2c_probe(struct i2c_client *client)
 {
-	const struct max310x_devtype *devtype =
-			device_get_match_data(&client->dev);
+	const struct max310x_devtype *devtype;
 	struct i2c_client *port_client;
 	struct regmap *regmaps[4];
 	unsigned int i;
 	u8 port_addr;
 
+	devtype = device_get_match_data(&client->dev);
+	if (!devtype)
+		return dev_err_probe(&client->dev, -ENODEV, "Failed to match device\n");
+
 	if (client->addr < devtype->slave_addr.min ||
 		client->addr > devtype->slave_addr.max)
 		return dev_err_probe(&client->dev, -EINVAL,
diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c
index aa2c51b84..589daed19 100644
--- a/drivers/tty/serial/samsung_tty.c
+++ b/drivers/tty/serial/samsung_tty.c
@@ -996,11 +996,10 @@ static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
 		if ((ufstat & info->tx_fifomask) != 0 ||
 		    (ufstat & info->tx_fifofull))
 			return 0;
-
-		return 1;
+		return TIOCSER_TEMT;
 	}
 
-	return s3c24xx_serial_txempty_nofifo(port);
+	return s3c24xx_serial_txempty_nofifo(port) ? TIOCSER_TEMT : 0;
 }
 
 /* no modem control lines */
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index f0ed30d0a..fe3f1d655 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -2561,7 +2561,12 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 			port->type = PORT_UNKNOWN;
 			flags |= UART_CONFIG_TYPE;
 		}
+		/* Synchronize with possible boot console. */
+		if (uart_console(port))
+			console_lock();
 		port->ops->config_port(port, flags);
+		if (uart_console(port))
+			console_unlock();
 	}
 
 	if (port->type != PORT_UNKNOWN) {
@@ -2569,6 +2574,10 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 
 		uart_report_port(drv, port);
 
+		/* Synchronize with possible boot console. */
+		if (uart_console(port))
+			console_lock();
+
 		/* Power up port for set_mctrl() */
 		uart_change_pm(state, UART_PM_STATE_ON);
 
@@ -2585,6 +2594,9 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 
 		uart_rs485_config(port);
 
+		if (uart_console(port))
+			console_unlock();
+
 		/*
 		 * If this driver supports console, and it hasn't been
 		 * successfully registered yet, try to re-register it.