diff options
Diffstat (limited to 'Documentation/devicetree/bindings/ata')
31 files changed, 2168 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-common.yaml b/Documentation/devicetree/bindings/ata/ahci-common.yaml new file mode 100644 index 000000000..94d72aeaa --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-common.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ahci-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Serial ATA AHCI controllers + +maintainers: + - Hans de Goede <hdegoede@redhat.com> + - Damien Le Moal <damien.lemoal@opensource.wdc.com> + +description: + This document defines device tree properties for a common AHCI SATA + controller implementation. It's hardware interface is supposed to + conform to the technical standard defined by Intel (see Serial ATA + Advanced Host Controller Interface specification for details). The + document doesn't constitute a DT-node binding by itself but merely + defines a set of common properties for the AHCI-compatible devices. + +select: false + +allOf: + - $ref: sata-common.yaml# + +properties: + reg: + description: + Generic AHCI registers space conforming to the Serial ATA AHCI + specification. + + reg-names: + description: CSR space IDs + contains: + const: ahci + + interrupts: + description: + Generic AHCI state change interrupt. Can be implemented either as a + single line attached to the controller or as a set of the signals + indicating the particular port events. + minItems: 1 + maxItems: 32 + + ahci-supply: + description: Power regulator for AHCI controller + + target-supply: + description: Power regulator for SATA target device + + phy-supply: + description: Power regulator for SATA PHY + + phys: + description: Reference to the SATA PHY node + maxItems: 1 + + phy-names: + const: sata-phy + + hba-cap: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Bitfield of the HBA generic platform capabilities like Staggered + Spin-up or Mechanical Presence Switch support. It can be used to + appropriately initialize the HWinit fields of the HBA CAP register + in case if the system firmware hasn't done it. + + ports-implemented: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Mask that indicates which ports the HBA supports. Useful if PI is not + programmed by the BIOS, which is true for some embedded SoC's. + +patternProperties: + "^sata-port@[0-9a-f]+$": + $ref: '#/$defs/ahci-port' + description: + It is optionally possible to describe the ports as sub-nodes so + to enable each port independently when dealing with multiple PHYs. + +required: + - reg + - interrupts + +additionalProperties: true + +$defs: + ahci-port: + $ref: /schemas/ata/sata-common.yaml#/$defs/sata-port + + properties: + reg: + description: + AHCI SATA port identifier. By design AHCI controller can't have + more than 32 ports due to the CAP.NP fields and PI register size + constraints. + minimum: 0 + maximum: 31 + + phys: + description: Individual AHCI SATA port PHY + maxItems: 1 + + phy-names: + description: AHCI SATA port PHY ID + const: sata-phy + + target-supply: + description: Power regulator for SATA port target device + + hba-port-cap: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Bitfield of the HBA port-specific platform capabilities like Hot + plugging, eSATA, FIS-based Switching, etc (see AHCI specification + for details). It can be used to initialize the HWinit fields of + the PxCMD register in case if the system firmware hasn't done it. + + required: + - reg + +... diff --git a/Documentation/devicetree/bindings/ata/ahci-da850.txt b/Documentation/devicetree/bindings/ata/ahci-da850.txt new file mode 100644 index 000000000..5f8193417 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-da850.txt @@ -0,0 +1,18 @@ +Device tree binding for the TI DA850 AHCI SATA Controller +--------------------------------------------------------- + +Required properties: + - compatible: must be "ti,da850-ahci" + - reg: physical base addresses and sizes of the two register regions + used by the controller: the register map as defined by the + AHCI 1.1 standard and the Power Down Control Register (PWRDN) + for enabling/disabling the SATA clock receiver + - interrupts: interrupt specifier (refer to the interrupt binding) + +Example: + + sata: sata@218000 { + compatible = "ti,da850-ahci"; + reg = <0x218000 0x2000>, <0x22c018 0x4>; + interrupts = <67>; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-dm816.txt b/Documentation/devicetree/bindings/ata/ahci-dm816.txt new file mode 100644 index 000000000..f8c535f35 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-dm816.txt @@ -0,0 +1,21 @@ +Device tree binding for the TI DM816 AHCI SATA Controller +--------------------------------------------------------- + +Required properties: + - compatible: must be "ti,dm816-ahci" + - reg: physical base address and size of the register region used by + the controller (as defined by the AHCI 1.1 standard) + - interrupts: interrupt specifier (refer to the interrupt binding) + - clocks: list of phandle and clock specifier pairs (or only + phandles for clock providers with '0' defined for + #clock-cells); two clocks must be specified: the functional + clock and an external reference clock + +Example: + + sata: sata@4a140000 { + compatible = "ti,dm816-ahci"; + reg = <0x4a140000 0x10000>; + interrupts = <16>; + clocks = <&sysclk5_ck>, <&sata_refclk>; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt new file mode 100644 index 000000000..7c3ca0e13 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt @@ -0,0 +1,21 @@ +Binding for Freescale QorIQ AHCI SATA Controller + +Required properties: + - reg: Physical base address and size of the controller's register area. + - compatible: Compatibility string. Must be 'fsl,<chip>-ahci', where + chip could be ls1021a, ls1043a, ls1046a, ls1088a, ls2080a etc. + - clocks: Input clock specifier. Refer to common clock bindings. + - interrupts: Interrupt specifier. Refer to interrupt binding. + +Optional properties: + - dma-coherent: Enable AHCI coherent DMA operation. + - reg-names: register area names when there are more than 1 register area. + +Examples: + sata@3200000 { + compatible = "fsl,ls1021a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&platform_clk 1>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-mtk.txt b/Documentation/devicetree/bindings/ata/ahci-mtk.txt new file mode 100644 index 000000000..d2aa696b1 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-mtk.txt @@ -0,0 +1,51 @@ +MediaTek Serial ATA controller + +Required properties: + - compatible : Must be "mediatek,<chip>-ahci", "mediatek,mtk-ahci". + When using "mediatek,mtk-ahci" compatible strings, you + need SoC specific ones in addition, one of: + - "mediatek,mt7622-ahci" + - reg : Physical base addresses and length of register sets. + - interrupts : Interrupt associated with the SATA device. + - interrupt-names : Associated name must be: "hostc". + - clocks : A list of phandle and clock specifier pairs, one for each + entry in clock-names. + - clock-names : Associated names must be: "ahb", "axi", "asic", "rbc", "pm". + - phys : A phandle and PHY specifier pair for the PHY port. + - phy-names : Associated name must be: "sata-phy". + - ports-implemented : See ./ahci-platform.txt for details. + +Optional properties: + - power-domains : A phandle and power domain specifier pair to the power + domain which is responsible for collapsing and restoring + power to the peripheral. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Associated names must be: "axi", "sw", "reg". + - mediatek,phy-mode : A phandle to the system controller, used to enable + SATA function. + +Example: + + sata: sata@1a200000 { + compatible = "mediatek,mt7622-ahci", + "mediatek,mtk-ahci"; + reg = <0 0x1a200000 0 0x1100>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hostc"; + clocks = <&pciesys CLK_SATA_AHB_EN>, + <&pciesys CLK_SATA_AXI_EN>, + <&pciesys CLK_SATA_ASIC_EN>, + <&pciesys CLK_SATA_RBC_EN>, + <&pciesys CLK_SATA_PM_EN>; + clock-names = "ahb", "axi", "asic", "rbc", "pm"; + phys = <&u3port1 PHY_TYPE_SATA>; + phy-names = "sata-phy"; + ports-implemented = <0x1>; + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; + resets = <&pciesys MT7622_SATA_AXI_BUS_RST>, + <&pciesys MT7622_SATA_PHY_SW_RST>, + <&pciesys MT7622_SATA_PHY_REG_RST>; + reset-names = "axi", "sw", "reg"; + mediatek,phy-mode = <&pciesys>; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.yaml b/Documentation/devicetree/bindings/ata/ahci-platform.yaml new file mode 100644 index 000000000..7dc2a2e8f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-platform.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ahci-platform.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AHCI SATA Controller + +description: | + SATA nodes are defined to describe on-chip Serial ATA controllers. + Each SATA controller should have its own node. + + It is possible, but not required, to represent each port as a sub-node. + It allows to enable each port independently when dealing with multiple + PHYs. + +maintainers: + - Hans de Goede <hdegoede@redhat.com> + - Jens Axboe <axboe@kernel.dk> + +select: + properties: + compatible: + contains: + enum: + - brcm,iproc-ahci + - cavium,octeon-7130-ahci + - hisilicon,hisi-ahci + - ibm,476gtr-ahci + - marvell,armada-3700-ahci + - marvell,armada-8k-ahci + - marvell,berlin2q-ahci + required: + - compatible + +allOf: + - $ref: "ahci-common.yaml#" + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,iproc-ahci + - marvell,armada-8k-ahci + - marvell,berlin2-ahci + - marvell,berlin2q-ahci + - const: generic-ahci + - enum: + - cavium,octeon-7130-ahci + - hisilicon,hisi-ahci + - ibm,476gtr-ahci + - marvell,armada-3700-ahci + + reg: + minItems: 1 + maxItems: 2 + + reg-names: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +patternProperties: + "^sata-port@[0-9a-f]+$": + $ref: /schemas/ata/ahci-common.yaml#/$defs/ahci-port + + anyOf: + - required: [ phys ] + - required: [ target-supply ] + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + sata@ffe08000 { + compatible = "snps,spear-ahci"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + }; + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/berlin2q.h> + #include <dt-bindings/ata/ahci.h> + + sata@f7e90000 { + compatible = "marvell,berlin2q-ahci", "generic-ahci"; + reg = <0xf7e90000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + + hba-cap = <HBA_SMPS>; + + sata0: sata-port@0 { + reg = <0>; + + phys = <&sata_phy 0>; + target-supply = <®_sata0>; + + hba-port-cap = <(HBA_PORT_FBSCP | HBA_PORT_ESP)>; + }; + + sata1: sata-port@1 { + reg = <1>; + + phys = <&sata_phy 1>; + target-supply = <®_sata1>; + + hba-port-cap = <(HBA_PORT_HPCP | HBA_PORT_MPSP | HBA_PORT_FBSCP)>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt new file mode 100644 index 000000000..909c99353 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -0,0 +1,35 @@ +STMicroelectronics STi SATA controller + +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,ahci" + - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY port + - phy-names : Associated name must be; "ahci_phy" + +Optional properties: + - resets : The power-down, soft-reset and power-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn", "sw-rst" and "pwr-rst" + +Example: + + /* Example for stih407 family silicon */ + sata0: sata@9b20000 { + compatible = "st,ahci"; + reg = <0x9b20000 0x1000>; + interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&phy_port0 PHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH407_SATA0_POWERDOWN>, + <&softreset STIH407_SATA0_SOFTRESET>, + <&softreset STIH407_SATA0_PWR_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst", "pwr-rst"; + clocks = <&clk_s_c0_flexgen CLK_ICN_REG>; + clock-names = "ahci_clk"; + }; diff --git a/Documentation/devicetree/bindings/ata/allwinner,sun4i-a10-ahci.yaml b/Documentation/devicetree/bindings/ata/allwinner,sun4i-a10-ahci.yaml new file mode 100644 index 000000000..cb530b46b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/allwinner,sun4i-a10-ahci.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/allwinner,sun4i-a10-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 AHCI SATA Controller bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + const: allwinner,sun4i-a10-ahci + + reg: + maxItems: 1 + + clocks: + items: + - description: AHCI Bus Clock + - description: AHCI Module Clock + + interrupts: + maxItems: 1 + + target-supply: + description: Regulator for SATA target power + +required: + - compatible + - reg + - clocks + - interrupts + +additionalProperties: false + +examples: + - | + ahci: sata@1c18000 { + compatible = "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <56>; + clocks = <&pll6 0>, <&ahb_gates 25>; + target-supply = <®_ahci_5v>; + }; diff --git a/Documentation/devicetree/bindings/ata/allwinner,sun8i-r40-ahci.yaml b/Documentation/devicetree/bindings/ata/allwinner,sun8i-r40-ahci.yaml new file mode 100644 index 000000000..e6b42a113 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/allwinner,sun8i-r40-ahci.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/allwinner,sun8i-r40-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner R40 AHCI SATA Controller bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + const: allwinner,sun8i-r40-ahci + + reg: + maxItems: 1 + + clocks: + items: + - description: AHCI Bus Clock + - description: AHCI Module Clock + + interrupts: + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + const: ahci + + ahci-supply: + description: Regulator for the AHCI controller + + phy-supply: + description: Regulator for the SATA PHY power + +required: + - compatible + - reg + - clocks + - interrupts + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-r40-ccu.h> + #include <dt-bindings/reset/sun8i-r40-ccu.h> + + ahci: sata@1c18000 { + compatible = "allwinner,sun8i-r40-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SATA>, <&ccu CLK_SATA>; + resets = <&ccu RST_BUS_SATA>; + reset-names = "ahci"; + ahci-supply = <®_dldo4>; + phy-supply = <®_eldo3>; + }; + +... diff --git a/Documentation/devicetree/bindings/ata/apm-xgene.txt b/Documentation/devicetree/bindings/ata/apm-xgene.txt new file mode 100644 index 000000000..02e690a67 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/apm-xgene.txt @@ -0,0 +1,77 @@ +* APM X-Gene 6.0 Gb/s SATA host controller nodes + +SATA host controller nodes are defined to describe on-chip Serial ATA +controllers. Each SATA controller (pair of ports) have its own node. + +Required properties: +- compatible : Shall contain: + * "apm,xgene-ahci" +- reg : First memory resource shall be the AHCI memory + resource. + Second memory resource shall be the host controller + core memory resource. + Third memory resource shall be the host controller + diagnostic memory resource. + 4th memory resource shall be the host controller + AXI memory resource. + 5th optional memory resource shall be the host + controller MUX memory resource if required. +- interrupts : Interrupt-specifier for SATA host controller IRQ. +- clocks : Reference to the clock entry. +- phys : A list of phandles + phy-specifiers, one for each + entry in phy-names. +- phy-names : Should contain: + * "sata-phy" for the SATA 6.0Gbps PHY + +Optional properties: +- dma-coherent : Present if dma operations are coherent +- status : Shall be "ok" if enabled or "disabled" if disabled. + Default is "ok". + +Example: + sataclk: sataclk { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <100000000>; + clock-output-names = "sataclk"; + }; + + phy2: phy@1f22a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f22a000 0x0 0x100>; + #phy-cells = <1>; + }; + + phy3: phy@1f23a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f23a000 0x0 0x100>; + #phy-cells = <1>; + }; + + sata2: sata@1a400000 { + compatible = "apm,xgene-ahci"; + reg = <0x0 0x1a400000 0x0 0x1000>, + <0x0 0x1f220000 0x0 0x1000>, + <0x0 0x1f22d000 0x0 0x1000>, + <0x0 0x1f22e000 0x0 0x1000>, + <0x0 0x1f227000 0x0 0x1000>; + interrupts = <0x0 0x87 0x4>; + dma-coherent; + clocks = <&sataclk 0>; + phys = <&phy2 0>; + phy-names = "sata-phy"; + }; + + sata3: sata@1a800000 { + compatible = "apm,xgene-ahci-pcie"; + reg = <0x0 0x1a800000 0x0 0x1000>, + <0x0 0x1f230000 0x0 0x1000>, + <0x0 0x1f23d000 0x0 0x1000>, + <0x0 0x1f23e000 0x0 0x1000>, + <0x0 0x1f237000 0x0 0x1000>; + interrupts = <0x0 0x88 0x4>; + dma-coherent; + clocks = <&sataclk 0>; + phys = <&phy3 0>; + phy-names = "sata-phy"; + }; diff --git a/Documentation/devicetree/bindings/ata/atmel-at91_cf.txt b/Documentation/devicetree/bindings/ata/atmel-at91_cf.txt new file mode 100644 index 000000000..c1d22b3ae --- /dev/null +++ b/Documentation/devicetree/bindings/ata/atmel-at91_cf.txt @@ -0,0 +1,19 @@ +Atmel AT91RM9200 CompactFlash + +Required properties: +- compatible : "atmel,at91rm9200-cf". +- reg : should specify localbus address and size used. +- gpios : specifies the gpio pins to control the CF device. Detect + and reset gpio's are mandatory while irq and vcc gpio's are + optional and may be set to 0 if not present. + +Example: +compact-flash@50000000 { + compatible = "atmel,at91rm9200-cf"; + reg = <0x50000000 0x30000000>; + gpios = <&pioC 13 0 /* irq */ + &pioC 15 0 /* detect */ + 0 /* vcc */ + &pioC 5 0 /* reset */ + >; +}; diff --git a/Documentation/devicetree/bindings/ata/baikal,bt1-ahci.yaml b/Documentation/devicetree/bindings/ata/baikal,bt1-ahci.yaml new file mode 100644 index 000000000..9b7ca4759 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/baikal,bt1-ahci.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/baikal,bt1-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 SoC AHCI SATA controller + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + AHCI SATA controller embedded into the Baikal-T1 SoC is based on the + DWC AHCI SATA v4.10a IP-core. + +allOf: + - $ref: snps,dwc-ahci-common.yaml# + +properties: + compatible: + const: baikal,bt1-ahci + + clocks: + items: + - description: Peripheral APB bus clock + - description: Application AXI BIU clock + - description: SATA Ports reference clock + + clock-names: + items: + - const: pclk + - const: aclk + - const: ref + + resets: + items: + - description: Application AXI BIU domain reset + - description: SATA Ports clock domain reset + + reset-names: + items: + - const: arst + - const: ref + + ports-implemented: + maximum: 0x3 + +patternProperties: + "^sata-port@[0-1]$": + $ref: /schemas/ata/snps,dwc-ahci-common.yaml#/$defs/dwc-ahci-port + + properties: + reg: + minimum: 0 + maximum: 1 + + snps,tx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Due to having AXI3 bus interface utilized the maximum Tx DMA + transaction size can't exceed 16 beats (AxLEN[3:0]). + enum: [ 1, 2, 4, 8, 16 ] + + snps,rx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Due to having AXI3 bus interface utilized the maximum Rx DMA + transaction size can't exceed 16 beats (AxLEN[3:0]). + enum: [ 1, 2, 4, 8, 16 ] + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +unevaluatedProperties: false + +examples: + - | + sata@1f050000 { + compatible = "baikal,bt1-ahci"; + reg = <0x1f050000 0x2000>; + #address-cells = <1>; + #size-cells = <0>; + + interrupts = <0 64 4>; + + clocks = <&ccu_sys 1>, <&ccu_axi 2>, <&sata_ref_clk>; + clock-names = "pclk", "aclk", "ref"; + + resets = <&ccu_axi 2>, <&ccu_sys 0>; + reset-names = "arst", "ref"; + + ports-implemented = <0x3>; + + sata-port@0 { + reg = <0>; + + snps,tx-ts-max = <4>; + snps,rx-ts-max = <4>; + }; + + sata-port@1 { + reg = <1>; + + snps,tx-ts-max = <4>; + snps,rx-ts-max = <4>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.yaml b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.yaml new file mode 100644 index 000000000..fe7f091e7 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/brcm,sata-brcm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom SATA3 AHCI Controller + +description: + SATA nodes are defined to describe on-chip Serial ATA controllers. + Each SATA controller should have its own node. + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +allOf: + - $ref: ahci-common.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,bcm7216-ahci + - brcm,bcm7445-ahci + - brcm,bcm7425-ahci + - brcm,bcm63138-ahci + - const: brcm,sata3-ahci + - items: + - const: brcm,bcm-nsp-ahci + + reg: + maxItems: 2 + + reg-names: + items: + - const: ahci + - const: top-ctrl + + interrupts: + maxItems: 1 + +if: + properties: + compatible: + contains: + enum: + - brcm,bcm7216-ahci + - brcm,bcm63138-ahci +then: + properties: + resets: + maxItems: 1 + reset-names: + enum: + - rescal + - ahci + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + +unevaluatedProperties: false + +examples: + - | + sata@f045a000 { + compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci"; + reg = <0xf045a000 0xa9c>, <0xf0458040 0x24>; + reg-names = "ahci", "top-ctrl"; + interrupts = <0 30 0>; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy 0>; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt new file mode 100644 index 000000000..3bacc8e09 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt @@ -0,0 +1,30 @@ +* Compact Flash + +The Cavium Compact Flash device is connected to the Octeon Boot Bus, +and is thus a child of the Boot Bus device. It can read and write +industry standard compact flash devices. + +Properties: +- compatible: "cavium,ebt3000-compact-flash"; + + Compatibility with many Cavium evaluation boards. + +- reg: The base address of the CF chip select banks. Depending on + the device configuration, there may be one or two banks. + +- cavium,bus-width: The width of the connection to the CF devices. Valid + values are 8 and 16. + +- cavium,true-ide: Optional, if present the CF connection is in True IDE mode. + +- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected + to this device. + +Example: + compact-flash@5,0 { + compatible = "cavium,ebt3000-compact-flash"; + reg = <5 0 0x10000>, <6 0 0x10000>; + cavium,bus-width = <16>; + cavium,true-ide; + cavium,dma-engine-handle = <&dma0>; + }; diff --git a/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml b/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml new file mode 100644 index 000000000..71364c608 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml @@ -0,0 +1,189 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ceva,ahci-1v84.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ceva AHCI SATA Controller + +maintainers: + - Piyush Mehta <piyush.mehta@xilinx.com> + +description: | + The Ceva SATA controller mostly conforms to the AHCI interface with some + special extensions to add functionality, is a high-performance dual-port + SATA host controller with an AHCI compliant command layer which supports + advanced features such as native command queuing and frame information + structure (FIS) based switching for systems employing port multipliers. + +properties: + compatible: + const: ceva,ahci-1v84 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + dma-coherent: true + + interrupts: + maxItems: 1 + + iommus: + maxItems: 4 + + power-domains: + maxItems: 1 + + ceva,p0-cominit-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMINIT parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + items: + - description: CINMP - COMINIT Negate Minimum Period. + - description: CIBGN - COMINIT Burst Gap Nominal. + - description: CIBGMX - COMINIT Burst Gap Maximum. + - description: CIBGMN - COMINIT Burst Gap Minimum. + + ceva,p0-comwake-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMWAKE parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + items: + - description: CWBGMN - COMWAKE Burst Gap Minimum. + - description: CWBGMX - COMWAKE Burst Gap Maximum. + - description: CWBGN - COMWAKE Burst Gap Nominal. + - description: CWNMP - COMWAKE Negate Minimum Period. + + ceva,p0-burst-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + Burst timing value for COM parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + items: + - description: BMX - COM Burst Maximum. + - description: BNM - COM Burst Nominal. + - description: SFD - Signal Failure Detection value. + - description: PTST - Partial to Slumber timer value. + + ceva,p0-retry-params: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: | + Retry interval timing value for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-retry-params = /bits/ 16 <RIT RCT>; + items: + - description: RIT - Retry Interval Timer. + - description: RCT - Rate Change Timer. + + ceva,p1-cominit-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMINIT parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + items: + - description: CINMP - COMINIT Negate Minimum Period. + - description: CIBGN - COMINIT Burst Gap Nominal. + - description: CIBGMX - COMINIT Burst Gap Maximum. + - description: CIBGMN - COMINIT Burst Gap Minimum. + + ceva,p1-comwake-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMWAKE parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + items: + - description: CWBGMN - COMWAKE Burst Gap Minimum. + - description: CWBGMX - COMWAKE Burst Gap Maximum. + - description: CWBGN - COMWAKE Burst Gap Nominal. + - description: CWNMP - COMWAKE Negate Minimum Period. + + ceva,p1-burst-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + Burst timing value for COM parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + items: + - description: BMX - COM Burst Maximum. + - description: BNM - COM Burst Nominal. + - description: SFD - Signal Failure Detection value. + - description: PTST - Partial to Slumber timer value. + + ceva,p1-retry-params: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: | + Retry interval timing value for port 1. + The fields for the above parameter must be as shown below:- + ceva,pN-retry-params = /bits/ 16 <RIT RCT>; + items: + - description: RIT - Retry Interval Timer. + - description: RCT - Rate Change Timer. + + ceva,broken-gen2: + $ref: /schemas/types.yaml#/definitions/flag + description: | + limit to gen1 speed instead of gen2. + + phys: + maxItems: 1 + + phy-names: + items: + - const: sata-phy + + resets: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - interrupts + - ceva,p0-cominit-params + - ceva,p0-comwake-params + - ceva,p0-burst-params + - ceva,p0-retry-params + - ceva,p1-cominit-params + - ceva,p1-comwake-params + - ceva,p1-burst-params + - ceva,p1-retry-params + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/xlnx-zynqmp-power.h> + #include <dt-bindings/reset/xlnx-zynqmp-resets.h> + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/phy/phy.h> + + sata: ahci@fd0c0000 { + compatible = "ceva,ahci-1v84"; + reg = <0xfd0c0000 0x200>; + interrupt-parent = <&gic>; + interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zynqmp_clk SATA_REF>; + ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>; + ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>; + ceva,broken-gen2; + phys = <&psgtr 1 PHY_TYPE_SATA 1 1>; + resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; + }; diff --git a/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file mode 100644 index 000000000..529093666 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/cortina,gemini-sata-bridge.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cortina Systems Gemini SATA Bridge + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that + takes two Faraday Technology FTIDE010 PATA controllers and bridges + them in different configurations to two SATA ports. + +properties: + compatible: + const: cortina,gemini-sata-bridge + + reg: + maxItems: 1 + + resets: + maxItems: 2 + description: phandles to the reset lines for both SATA bridges + + reset-names: + items: + - const: sata0 + - const: sata1 + + clocks: + maxItems: 2 + description: phandles to the compulsory peripheral clocks + + clock-names: + items: + - const: SATA0_PCLK + - const: SATA1_PCLK + + syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the global Gemini system controller + + cortina,gemini-ata-muxmode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 + - 1 + - 2 + - 3 + description: | + Tell the desired multiplexing mode for the ATA controller and SATA + bridges. + Mode 0: ata0 master <-> sata0 + ata1 master <-> sata1 + ata0 slave interface brought out on IDE pads + Mode 1: ata0 master <-> sata0 + ata1 master <-> sata1 + ata1 slave interface brought out on IDE pads + Mode 2: ata1 master <-> sata1 + ata1 slave <-> sata0 + ata0 master and slave interfaces brought out on IDE pads + Mode 3: ata0 master <-> sata0 + ata0 slave <-> sata1 + ata1 master and slave interfaces brought out on IDE pads + + cortina,gemini-enable-ide-pins: + type: boolean + description: Enables the PATA to IDE connection. + The muxmode setting decides whether ATA0 or ATA1 is brought out, + and whether master, slave or both interfaces get brought out. + + cortina,gemini-enable-sata-bridge: + type: boolean + description: Enables the PATA to SATA bridge inside the Gemnini SoC. + The Muxmode decides what PATA blocks will be muxed out and how. + +required: + - clocks + - clock-names + - cortina,gemini-ata-muxmode + - resets + - reset-names + - compatible + - reg + - syscon + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/cortina,gemini-clock.h> + sata@46000000 { + compatible = "cortina,gemini-sata-bridge"; + reg = <0x46000000 0x100>; + resets = <&rcon 26>, <&rcon 27>; + reset-names = "sata0", "sata1"; + clocks = <&gcc GEMINI_CLK_GATE_SATA0>, + <&gcc GEMINI_CLK_GATE_SATA1>; + clock-names = "SATA0_PCLK", "SATA1_PCLK"; + syscon = <&syscon>; + cortina,gemini-ata-muxmode = <3>; + cortina,gemini-enable-ide-pins; + cortina,gemini-enable-sata-bridge; + }; diff --git a/Documentation/devicetree/bindings/ata/faraday,ftide010.yaml b/Documentation/devicetree/bindings/ata/faraday,ftide010.yaml new file mode 100644 index 000000000..fa16f3767 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/faraday,ftide010.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/faraday,ftide010.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Faraday Technology FTIDE010 PATA controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + This controller is the first Faraday IDE interface block, used in the + StorLink SL3512 and SL3516, later known as the Cortina Systems Gemini + platform. The controller can do PIO modes 0 through 4, Multi-word DMA + (MWDM) modes 0 through 2 and Ultra DMA modes 0 through 6. + + On the Gemini platform, this PATA block is accompanied by a PATA to + SATA bridge in order to support SATA. This is why a phandle to that + controller is compulsory on that platform. + + The timing properties are unique per-SoC, not per-board. + +properties: + compatible: + oneOf: + - const: faraday,ftide010 + - items: + - const: cortina,gemini-pata + - const: faraday,ftide010 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + + clock-names: + const: PCLK + + sata: + description: + phandle to the Gemini PATA to SATA bridge, if available + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: pata-common.yaml# + + - if: + properties: + compatible: + contains: + const: cortina,gemini-pata + + then: + required: + - sata + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/cortina,gemini-clock.h> + + ide@63000000 { + compatible = "cortina,gemini-pata", "faraday,ftide010"; + reg = <0x63000000 0x100>; + interrupts = <4 IRQ_TYPE_EDGE_RISING>; + clocks = <&gcc GEMINI_CLK_GATE_IDE>; + clock-names = "PCLK"; + sata = <&sata>; + #address-cells = <1>; + #size-cells = <0>; + ide-port@0 { + reg = <0>; + }; + ide-port@1 { + reg = <1>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/ata/fsl-sata.txt b/Documentation/devicetree/bindings/ata/fsl-sata.txt new file mode 100644 index 000000000..fd63bb3be --- /dev/null +++ b/Documentation/devicetree/bindings/ata/fsl-sata.txt @@ -0,0 +1,28 @@ +* Freescale 8xxx/3.0 Gb/s SATA nodes + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA port should have its own node. + +Required properties: +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-sata", where CHIP is the processor + (mpc8315, mpc8379, etc.) and the second is + "fsl,pq-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- cell-index : controller index. + 1 for controller @ 0x18000 + 2 for controller @ 0x19000 + 3 for controller @ 0x1a000 + 4 for controller @ 0x1b000 + +Optional properties: +- reg : <registers mapping> + +Example: + sata@18000 { + compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; + reg = <0x18000 0x1000>; + cell-index = <1>; + interrupts = <2c 8>; + interrupt-parent = < &ipic >; + }; diff --git a/Documentation/devicetree/bindings/ata/imx-pata.txt b/Documentation/devicetree/bindings/ata/imx-pata.txt new file mode 100644 index 000000000..f1172f001 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-pata.txt @@ -0,0 +1,16 @@ +* Freescale i.MX PATA Controller + +Required properties: +- compatible: "fsl,imx27-pata" +- reg: Address range of the PATA Controller +- interrupts: The interrupt of the PATA Controller +- clocks: the clocks for the PATA Controller + +Example: + + pata: pata@83fe0000 { + compatible = "fsl,imx51-pata", "fsl,imx27-pata"; + reg = <0x83fe0000 0x4000>; + interrupts = <70>; + clocks = <&clks 161>; + }; diff --git a/Documentation/devicetree/bindings/ata/imx-sata.yaml b/Documentation/devicetree/bindings/ata/imx-sata.yaml new file mode 100644 index 000000000..68ffb97dd --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-sata.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/imx-sata.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX AHCI SATA Controller + +maintainers: + - Shawn Guo <shawn.guo@linaro.org> + +description: | + The Freescale i.MX SATA controller mostly conforms to the AHCI interface + with some special extensions at integration level. + +properties: + compatible: + enum: + - fsl,imx53-ahci + - fsl,imx6q-ahci + - fsl,imx6qp-ahci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: sata clock + - description: sata reference clock + - description: ahb clock + + clock-names: + items: + - const: sata + - const: sata_ref + - const: ahb + + fsl,transmit-level-mV: + $ref: /schemas/types.yaml#/definitions/uint32 + description: transmit voltage level, in millivolts. + + fsl,transmit-boost-mdB: + $ref: /schemas/types.yaml#/definitions/uint32 + description: transmit boost level, in milli-decibels. + + fsl,transmit-atten-16ths: + $ref: /schemas/types.yaml#/definitions/uint32 + description: transmit attenuation, in 16ths. + + fsl,receive-eq-mdB: + $ref: /schemas/types.yaml#/definitions/uint32 + description: receive equalisation, in milli-decibels. + + fsl,no-spread-spectrum: + $ref: /schemas/types.yaml#/definitions/flag + description: if present, disable spread-spectrum clocking on the SATA link. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + sata@2200000 { + compatible = "fsl,imx6q-ahci"; + reg = <0x02200000 0x4000>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_SATA>, + <&clks IMX6QDL_CLK_SATA_REF_100M>, + <&clks IMX6QDL_CLK_AHB>; + clock-names = "sata", "sata_ref", "ahb"; + }; diff --git a/Documentation/devicetree/bindings/ata/intel,ixp4xx-compact-flash.yaml b/Documentation/devicetree/bindings/ata/intel,ixp4xx-compact-flash.yaml new file mode 100644 index 000000000..52e18600e --- /dev/null +++ b/Documentation/devicetree/bindings/ata/intel,ixp4xx-compact-flash.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/intel,ixp4xx-compact-flash.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel IXP4xx CompactFlash Card Controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The IXP4xx network processors have a CompactFlash interface that presents + a CompactFlash card to the system as a true IDE (parallel ATA) device. The + device is always connected to the expansion bus of the IXP4xx SoCs using one + or two chip select areas and address translating logic on the board. The + node must be placed inside a chip select node on the IXP4xx expansion bus. + +properties: + compatible: + const: intel,ixp4xx-compact-flash + + reg: + items: + - description: Command interface registers + - description: Control interface registers + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: pata-common.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + bus@c4000000 { + compatible = "intel,ixp43x-expansion-bus-controller", "syscon"; + reg = <0xc4000000 0x1000>; + native-endian; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x01000000>, <1 0x0 0x51000000 0x01000000>; + dma-ranges = <0 0x0 0x50000000 0x01000000>, <1 0x0 0x51000000 0x01000000>; + ide@1,0 { + compatible = "intel,ixp4xx-compact-flash"; + reg = <1 0x00000000 0x1000>, <1 0x00040000 0x1000>; + interrupt-parent = <&gpio0>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/ata/marvell.txt b/Documentation/devicetree/bindings/ata/marvell.txt new file mode 100644 index 000000000..b460edd12 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/marvell.txt @@ -0,0 +1,22 @@ +* Marvell Orion SATA + +Required Properties: +- compatibility : "marvell,orion-sata" or "marvell,armada-370-sata" +- reg : Address range of controller +- interrupts : Interrupt controller is using +- nr-ports : Number of SATA ports in use. + +Optional Properties: +- phys : List of phandles to sata phys +- phy-names : Should be "0", "1", etc, one number per phandle + +Example: + + sata@80000 { + compatible = "marvell,orion-sata"; + reg = <0x80000 0x5000>; + interrupts = <21>; + phys = <&sata_phy0>, <&sata_phy1>; + phy-names = "0", "1"; + nr-ports = <2>; + } diff --git a/Documentation/devicetree/bindings/ata/nvidia,tegra-ahci.yaml b/Documentation/devicetree/bindings/ata/nvidia,tegra-ahci.yaml new file mode 100644 index 000000000..3c7a2425f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/nvidia,tegra-ahci.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/nvidia,tegra-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Tegra AHCI SATA Controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jonathan Hunter <jonathanh@nvidia.com> + +properties: + compatible: + enum: + - nvidia,tegra124-ahci + - nvidia,tegra132-ahci + - nvidia,tegra210-ahci + - nvidia,tegra186-ahci + + reg: + minItems: 2 + items: + - description: AHCI registers + - description: SATA configuration and IPFS registers + - description: SATA AUX registers + + interrupts: + maxItems: 1 + + clock-names: + items: + - const: sata + - const: sata-oob + + clocks: + maxItems: 2 + + reset-names: + minItems: 2 + items: + - const: sata + - const: sata-cold + - const: sata-oob + + resets: + minItems: 2 + maxItems: 3 + + iommus: + maxItems: 1 + + interconnect-names: + items: + - const: dma-mem + - const: write + + interconnects: + maxItems: 2 + + power-domains: + items: + - description: SAX power-domain + + phy-names: + items: + - const: sata-0 + + phys: + maxItems: 1 + + hvdd-supply: + description: SATA HVDD regulator supply. + + vddio-supply: + description: SATA VDDIO regulator supply. + + avdd-supply: + description: SATA AVDD regulator supply. + + target-5v-supply: + description: SATA 5V power regulator supply. + + target-12v-supply: + description: SATA 12V power regulator supply. + +required: + - compatible + - reg + - interrupts + - clock-names + - clocks + - reset-names + - resets + +allOf: + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra124-ahci + - nvidia,tegra132-ahci + then: + properties: + reg: + maxItems: 2 + reset-names: + minItems: 3 + resets: + minItems: 3 + required: + - phys + - phy-names + - hvdd-supply + - vddio-supply + - avdd-supply + + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra210-ahci + then: + properties: + reg: + minItems: 3 + reset-names: + minItems: 3 + resets: + minItems: 3 + + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra186-ahci + then: + properties: + reg: + minItems: 3 + reset-names: + maxItems: 2 + resets: + maxItems: 2 + required: + - iommus + - interconnect-names + - interconnects + - power-domains + +additionalProperties: true + +examples: + - | + #include <dt-bindings/clock/tegra210-car.h> + #include <dt-bindings/reset/tegra210-car.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + sata@70020000 { + compatible = "nvidia,tegra210-ahci"; + reg = <0x70027000 0x00002000>, /* AHCI */ + <0x70020000 0x00007000>, /* SATA */ + <0x70001100 0x00010000>; /* SATA AUX */ + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SATA>, + <&tegra_car TEGRA210_CLK_SATA_OOB>; + clock-names = "sata", "sata-oob"; + resets = <&tegra_car 124>, + <&tegra_car 129>, + <&tegra_car 123>; + reset-names = "sata", "sata-cold", "sata-oob"; + }; diff --git a/Documentation/devicetree/bindings/ata/pata-arasan.txt b/Documentation/devicetree/bindings/ata/pata-arasan.txt new file mode 100644 index 000000000..872edc105 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/pata-arasan.txt @@ -0,0 +1,37 @@ +* ARASAN PATA COMPACT FLASH CONTROLLER + +Required properties: +- compatible: "arasan,cf-spear1340" +- reg: Address range of the CF registers +- interrupt: Should contain the CF interrupt number +- clock-frequency: Interface clock rate, in Hz, one of + 25000000 + 33000000 + 40000000 + 50000000 + 66000000 + 75000000 + 100000000 + 125000000 + 150000000 + 166000000 + 200000000 + +Optional properties: +- arasan,broken-udma: if present, UDMA mode is unusable +- arasan,broken-mwdma: if present, MWDMA mode is unusable +- arasan,broken-pio: if present, PIO mode is unusable +- dmas: one DMA channel, as described in bindings/dma/dma.txt + required unless both UDMA and MWDMA mode are broken +- dma-names: the corresponding channel name, must be "data" + +Example: + + cf@fc000000 { + compatible = "arasan,cf-spear1340"; + reg = <0xfc000000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + dmas = <&dma-controller 23>; + dma-names = "data"; + }; diff --git a/Documentation/devicetree/bindings/ata/pata-common.yaml b/Documentation/devicetree/bindings/ata/pata-common.yaml new file mode 100644 index 000000000..2412894a2 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/pata-common.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/pata-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Parallel AT attachment (PATA) controllers + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + This document defines device tree properties common to most Parallel + ATA (PATA, also known as IDE) AT attachment storage devices. + It doesn't constitue a device tree binding specification by itself but is + meant to be referenced by device tree bindings. + + The PATA (IDE) controller-specific device tree bindings are responsible for + defining whether each property is required or optional. + +properties: + $nodename: + pattern: "^ide(@.*)?$" + description: + Specifies the host controller node. PATA host controller nodes are named + "ide". + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^ide-port@[0-1]$": + description: | + DT nodes for ports connected on the PATA host. The master drive will have + ID number 0 and the slave drive will have ID number 1. The PATA port + nodes will be named "ide-port". + type: object + + properties: + reg: + minimum: 0 + maximum: 1 + description: + The ID number of the drive port, 0 for the master port and 1 for the + slave port. + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/ata/qcom-sata.txt b/Documentation/devicetree/bindings/ata/qcom-sata.txt new file mode 100644 index 000000000..094de91cd --- /dev/null +++ b/Documentation/devicetree/bindings/ata/qcom-sata.txt @@ -0,0 +1,48 @@ +* Qualcomm AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, must contain "generic-ahci" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- phys : Must contain exactly one entry as specified + in phy-bindings.txt +- phy-names : Must be "sata-phy" + +Required properties for "qcom,ipq806x-ahci" compatible: +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be: + "slave_iface" - Fabric port AHB clock for SATA + "iface" - AHB clock + "core" - core clock + "rxoob" - RX out-of-band clock + "pmalive" - Power Module Alive clock +- assigned-clocks : Shall be: + SATA_RXOOB_CLK + SATA_PMALIVE_CLK +- assigned-clock-rates : Shall be: + 100Mhz (100000000) for SATA_RXOOB_CLK + 100Mhz (100000000) for SATA_PMALIVE_CLK + +Example: + sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <0 209 0x0>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_iface", "iface", "core", + "rxoob", "pmalive"; + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + }; diff --git a/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml b/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml new file mode 100644 index 000000000..c4e4a9eab --- /dev/null +++ b/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/ata/renesas,rcar-sata.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas R-Car Serial-ATA Interface + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,sata-r8a7779 # R-Car H1 + - items: + - enum: + - renesas,sata-r8a7742 # RZ/G1H + - renesas,sata-r8a7790-es1 # R-Car H2 ES1 + - renesas,sata-r8a7790 # R-Car H2 other than ES1 + - renesas,sata-r8a7791 # R-Car M2-W + - renesas,sata-r8a7793 # R-Car M2-N + - const: renesas,rcar-gen2-sata # generic R-Car Gen2 + - items: + - enum: + - renesas,sata-r8a774b1 # RZ/G2N + - renesas,sata-r8a774e1 # RZ/G2H + - renesas,sata-r8a7795 # R-Car H3 + - renesas,sata-r8a77965 # R-Car M3-N + - const: renesas,rcar-gen3-sata # generic R-Car Gen3 or RZ/G2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + +if: + not: + properties: + compatible: + contains: + const: renesas,sata-r8a7779 +then: + required: + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7791-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7791-sysc.h> + + sata@ee300000 { + compatible = "renesas,sata-r8a7791", "renesas,rcar-gen2-sata"; + reg = <0xee300000 0x200000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 815>; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 815>; + }; diff --git a/Documentation/devicetree/bindings/ata/sata-common.yaml b/Documentation/devicetree/bindings/ata/sata-common.yaml new file mode 100644 index 000000000..58c9342b9 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/sata-common.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/sata-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Serial AT attachment (SATA) controllers + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + This document defines device tree properties common to most Serial + AT attachment (SATA) storage devices. It doesn't constitute a device tree + binding specification by itself but is meant to be referenced by device + tree bindings. + + The SATA controller-specific device tree bindings are responsible for + defining whether each property is required or optional. + +properties: + $nodename: + pattern: "^sata(@.*)?$" + description: + Specifies the host controller node. SATA host controller nodes are named + "sata" + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + dma-coherent: true + +patternProperties: + "^sata-port@[0-9a-e]$": + $ref: '#/$defs/sata-port' + description: | + DT nodes for ports connected on the SATA host. The SATA port + nodes will be named "sata-port". + +additionalProperties: true + +$defs: + sata-port: + type: object + + properties: + reg: + minimum: 0 + description: + The ID number of the SATA port. Aside with being directly used, + each port can have a Port Multiplier attached thus allowing to + access more than one drive by means of a single SATA port. + +... diff --git a/Documentation/devicetree/bindings/ata/sata_highbank.yaml b/Documentation/devicetree/bindings/ata/sata_highbank.yaml new file mode 100644 index 000000000..f23f26a8f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/sata_highbank.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/sata_highbank.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Calxeda AHCI SATA Controller + +description: | + The Calxeda SATA controller mostly conforms to the AHCI interface + with some special extensions to add functionality, to map GPIOs for + activity LEDs and for mapping the ComboPHYs. + +maintainers: + - Andre Przywara <andre.przywara@arm.com> + +properties: + compatible: + const: calxeda,hb-ahci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + dma-coherent: true + + calxeda,pre-clocks: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Indicates the number of additional clock cycles to transmit before + sending an SGPIO pattern. + + calxeda,post-clocks: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Indicates the number of additional clock cycles to transmit after + sending an SGPIO pattern. + + calxeda,led-order: + description: Maps port numbers to offsets within the SGPIO bitstream. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + + calxeda,port-phys: + description: | + phandle-combophy and lane assignment, which maps each SATA port to a + combophy and a lane within that combophy + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 1 + maxItems: 8 + items: + maxItems: 2 + + calxeda,tx-atten: + description: | + Contains TX attenuation override codes, one per port. + The upper 24 bits of each entry are always 0 and thus ignored. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + + calxeda,sgpio-gpio: + maxItems: 3 + description: | + phandle-gpio bank, bit offset, and default on or off, which indicates + that the driver supports SGPIO indicator lights using the indicated + GPIOs. + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + sata@ffe08000 { + compatible = "calxeda,hb-ahci"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + dma-coherent; + calxeda,port-phys = <&combophy5 0>, <&combophy0 0>, <&combophy0 1>, + <&combophy0 2>, <&combophy0 3>; + calxeda,sgpio-gpio =<&gpioh 5 1>, <&gpioh 6 1>, <&gpioh 7 1>; + calxeda,led-order = <4 0 1 2 3>; + calxeda,tx-atten = <0xff 22 0xff 0xff 23>; + calxeda,pre-clocks = <10>; + calxeda,post-clocks = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml new file mode 100644 index 000000000..c14579105 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/snps,dwc-ahci-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DWC AHCI SATA controller properties + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + This document defines device tree schema for the generic Synopsys DWC + AHCI controller properties. + +select: false + +allOf: + - $ref: ahci-common.yaml# + +properties: + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: + Basic DWC AHCI SATA clock sources like application AXI/AHB BIU clock, + PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx) + clock, etc. + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + oneOf: + - description: Application APB/AHB/AXI BIU clock + enum: + - pclk + - aclk + - hclk + - sata + - description: Power Module keep-alive clock + const: pmalive + - description: RxOOB detection clock + const: rxoob + - description: SATA Ports reference clock + const: ref + + resets: + description: + At least basic application and reference clock domains resets are + normally supported by the DWC AHCI SATA controller. + minItems: 1 + maxItems: 4 + + reset-names: + minItems: 1 + maxItems: 4 + items: + oneOf: + - description: Application AHB/AXI BIU clock domain reset control + enum: + - arst + - hrst + - description: Power Module keep-alive clock domain reset control + const: pmalive + - description: RxOOB detection clock domain reset control + const: rxoob + - description: Reference clock domain reset control + const: ref + +patternProperties: + "^sata-port@[0-9a-e]$": + $ref: '#/$defs/dwc-ahci-port' + +additionalProperties: true + +$defs: + dwc-ahci-port: + $ref: /schemas/ata/ahci-common.yaml#/$defs/ahci-port + + properties: + reg: + minimum: 0 + maximum: 7 + + snps,tx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximal size of Tx DMA transactions in FIFO words + enum: [ 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 ] + + snps,rx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximal size of Rx DMA transactions in FIFO words + enum: [ 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 ] + +... diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml new file mode 100644 index 000000000..5afa4b57c --- /dev/null +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/snps,dwc-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DWC AHCI SATA controller + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + This document defines device tree bindings for the generic Synopsys DWC + implementation of the AHCI SATA controller. + +allOf: + - $ref: snps,dwc-ahci-common.yaml# + +properties: + compatible: + oneOf: + - description: Synopsys AHCI SATA-compatible devices + const: snps,dwc-ahci + - description: SPEAr1340 AHCI SATA device + const: snps,spear-ahci + - description: Rockhip RK3568 AHCI controller + items: + - const: rockchip,rk3568-dwc-ahci + - const: snps,dwc-ahci + +patternProperties: + "^sata-port@[0-9a-e]$": + $ref: /schemas/ata/snps,dwc-ahci-common.yaml#/$defs/dwc-ahci-port + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/ata/ahci.h> + + sata@122f0000 { + compatible = "snps,dwc-ahci"; + reg = <0x122F0000 0x1ff>; + #address-cells = <1>; + #size-cells = <0>; + + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clock1>, <&clock2>; + clock-names = "aclk", "ref"; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + + ports-implemented = <0x1>; + + sata-port@0 { + reg = <0>; + + hba-port-cap = <HBA_PORT_FBSCP>; + + snps,tx-ts-max = <512>; + snps,rx-ts-max = <512>; + }; + }; + +... |