1 files changed, 112 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
new file mode 100644
index 000000000..1c94a57a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
@@ -0,0 +1,112 @@
+Marvell ICU Interrupt Controller
+--------------------------------
+
+The Marvell ICU (Interrupt Consolidation Unit) controller is
+responsible for collecting all wired-interrupt sources in the CP and
+communicating them to the GIC in the AP, the unit translates interrupt
+requests on input wires to MSG memory mapped transactions to the GIC.
+These messages will access a different GIC memory area depending on
+their type (NSR, SR, SEI, REI, etc).
+
+Required properties:
+
+- compatible: Should be "marvell,cp110-icu"
+
+- reg: Should contain ICU registers location and length.
+
+Subnodes: Each group of interrupt is declared as a subnode of the ICU,
+with their own compatible.
+
+Required properties for the icu_nsr/icu_sei subnodes:
+
+- compatible: Should be one of:
+              * "marvell,cp110-icu-nsr"
+	      * "marvell,cp110-icu-sr"
+	      * "marvell,cp110-icu-sei"
+	      * "marvell,cp110-icu-rei"
+
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2.
+
+  The 1st cell is the index of the interrupt in the ICU unit.
+
+  The 2nd cell is the type of the interrupt. See arm,gic.txt for
+  details.
+
+- interrupt-controller: Identifies the node as an interrupt
+  controller.
+
+- msi-parent: Should point to the GICP controller, the GIC extension
+  that allows to trigger interrupts using MSG memory mapped
+  transactions.
+
+Note: each 'interrupts' property referring to any 'icu_xxx' node shall
+      have a different number within [0:206].
+
+Example:
+
+icu: interrupt-controller@1e0000 {
+	compatible = "marvell,cp110-icu";
+	reg = <0x1e0000 0x440>;
+
+	CP110_LABEL(icu_nsr): interrupt-controller@10 {
+		compatible = "marvell,cp110-icu-nsr";
+		reg = <0x10 0x20>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		msi-parent = <&gicp>;
+	};
+
+	CP110_LABEL(icu_sei): interrupt-controller@50 {
+		compatible = "marvell,cp110-icu-sei";
+		reg = <0x50 0x10>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		msi-parent = <&sei>;
+	};
+};
+
+node1 {
+	interrupt-parent = <&icu_nsr>;
+	interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+node2 {
+	interrupt-parent = <&icu_sei>;
+	interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+/* Would not work with the above nodes */
+node3 {
+	interrupt-parent = <&icu_nsr>;
+	interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+The legacy bindings were different in this way:
+
+- #interrupt-cells: The value was 3.
+	The 1st cell was the group type of the ICU interrupt. Possible
+	group types were:
+	ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure
+	ICU_GRP_SR  (0x1) : Shared peripheral interrupt, secure
+	ICU_GRP_SEI (0x4) : System error interrupt
+	ICU_GRP_REI (0x5) : RAM error interrupt
+	The 2nd cell was the index of the interrupt in the ICU unit.
+	The 3rd cell was the type of the interrupt. See arm,gic.txt for
+	details.
+
+Example:
+
+icu: interrupt-controller@1e0000 {
+	compatible = "marvell,cp110-icu";
+	reg = <0x1e0000 0x440>;
+
+	#interrupt-cells = <3>;
+	interrupt-controller;
+	msi-parent = <&gicp>;
+};
+
+node1 {
+	interrupt-parent = <&icu>;
+	interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>;
+};