diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/cpsw.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/cpsw.txt | 132 |
1 files changed, 132 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt new file mode 100644 index 000000000..ef655f386 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -0,0 +1,132 @@ +TI SoC Ethernet Switch Controller Device Tree Bindings +------------------------------------------------------ + +Required properties: +- compatible : Should be one of the below:- + "ti,cpsw" for backward compatible + "ti,am335x-cpsw" for AM335x controllers + "ti,am4372-cpsw" for AM437x controllers + "ti,dra7-cpsw" for DRA7x controllers +- reg : physical base address and size of the cpsw + registers map +- interrupts : property with a value describing the interrupt + number +- cpdma_channels : Specifies number of channels in CPDMA +- ale_entries : Specifies No of entries ALE can hold +- bd_ram_size : Specifies internal descriptor RAM size +- mac_control : Specifies Default MAC control register content + for the specific platform +- slaves : Specifies number for slaves +- active_slave : Specifies the slave to use for time stamping, + ethtool and SIOCGMIIPHY +- cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection + device. See also cpsw-phy-sel.txt for its binding. + Note that in legacy cases cpsw-phy-sel may be + a child device instead of a phandle + (DEPRECATED, use phys property instead). + +Optional properties: +- ti,hwmods : Must be "cpgmac0" +- dual_emac : Specifies Switch to act as Dual EMAC +- syscon : Phandle to the system control device node, which is + the control module device of the am33x +- mode-gpios : Should be added if one/multiple gpio lines are + required to be driven so that cpsw data lines + can be connected to the phy via selective mux. + For example in dra72x-evm, pcf gpio has to be + driven low so that cpsw slave 0 and phy data + lines are connected via mux. +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. + +Slave Properties: +Required properties: +- phy-mode : See ethernet.txt file in the same directory +- phys : phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt) + +Optional properties: +- dual_emac_res_vlan : Specifies VID to be used to segregate the ports +- phy_id : Specifies slave phy id (deprecated, use phy-handle) +- phy-handle : See ethernet.txt file in the same directory + +The MAC address will be determined using the optional properties +defined in ethernet.txt. + +Slave sub-nodes: +- fixed-link : See fixed-link.txt file in the same directory + +Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified. + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mac: ethernet@4a100000 { + compatible = "ti,cpsw"; + reg = <0x4A100000 0x1000>; + interrupts = <55 0x4>; + interrupt-parent = <&intc>; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; + cpsw_emac0: slave@0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1 0>; + }; + cpsw_emac1: slave@1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2 0>; + }; + }; + +(or) + mac: ethernet@4a100000 { + compatible = "ti,cpsw"; + ti,hwmods = "cpgmac0"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; + cpsw_emac0: slave@0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1 0>; + }; + cpsw_emac1: slave@1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2 0>; + }; + }; |