diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/realtek.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/realtek.yaml | 386 |
1 files changed, 386 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml new file mode 100644 index 000000000..1a7d45a8a --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml @@ -0,0 +1,386 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/realtek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek switches for unmanaged switches + +allOf: + - $ref: dsa.yaml# + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + Realtek advertises these chips as fast/gigabit switches or unmanaged + switches. They can be controlled using different interfaces, like SMI, + MDIO or SPI. + + The SMI "Simple Management Interface" is a two-wire protocol using + bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does + not use the MDIO protocol. This binding defines how to specify the + SMI-based Realtek devices. The realtek-smi driver is a platform driver + and it must be inserted inside a platform node. + + The MDIO-connected switches use MDIO protocol to access their registers. + The realtek-mdio driver is an MDIO driver and it must be inserted inside + an MDIO node. + + The compatible string is only used to identify which (silicon) family the + switch belongs to. Roughly speaking, a family is any set of Realtek switches + whose chip identification register(s) have a common location and semantics. + The different models in a given family can be automatically disambiguated by + parsing the chip identification register(s) according to the given family, + avoiding the need for a unique compatible string for each model. + +properties: + compatible: + enum: + - realtek,rtl8365mb + - realtek,rtl8366rb + description: | + realtek,rtl8365mb: + Use with models RTL8363NB, RTL8363NB-VB, RTL8363SC, RTL8363SC-VB, + RTL8364NB, RTL8364NB-VB, RTL8365MB, RTL8366SC, RTL8367RB-VB, RTL8367S, + RTL8367SB, RTL8370MB, RTL8310SR + realtek,rtl8366rb: + Use with models RTL8366RB, RTL8366S + + mdc-gpios: + description: GPIO line for the MDC clock line. + maxItems: 1 + + mdio-gpios: + description: GPIO line for the MDIO data line. + maxItems: 1 + + reset-gpios: + description: GPIO to be used to reset the whole device + maxItems: 1 + + realtek,disable-leds: + type: boolean + description: | + if the LED drivers are not used in the hardware design, + this will disable them so they are not turned on + and wasting power. + + interrupt-controller: + type: object + description: | + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the Realtek switch chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + + properties: + + interrupt-controller: true + + interrupts: + maxItems: 1 + description: + A single IRQ line from the switch, either active LOW or HIGH + + '#address-cells': + const: 0 + + '#interrupt-cells': + const: 1 + + required: + - interrupt-controller + - '#address-cells' + - '#interrupt-cells' + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + const: realtek,smi-mdio + +if: + required: + - reg + +then: + $ref: /schemas/spi/spi-peripheral-props.yaml# + not: + required: + - mdc-gpios + - mdio-gpios + - mdio + + properties: + mdc-gpios: false + mdio-gpios: false + mdio: false + +else: + required: + - mdc-gpios + - mdio-gpios + - mdio + - reset-gpios + +required: + - compatible + + # - mdc-gpios + # - mdio-gpios + # - reset-gpios + # - mdio + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc1: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc1>; + interrupts = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc1>; + interrupts = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc1>; + interrupts = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc1>; + interrupts = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc1>; + interrupts = <12>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8365mb"; + mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + + switch_intc2: interrupt-controller { + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "swp0"; + phy-handle = <ðphy0>; + }; + port@1 { + reg = <1>; + label = "swp1"; + phy-handle = <ðphy1>; + }; + port@2 { + reg = <2>; + label = "swp2"; + phy-handle = <ðphy2>; + }; + port@3 { + reg = <3>; + label = "swp3"; + phy-handle = <ðphy3>; + }; + port@6 { + reg = <6>; + ethernet = <&fec1>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc2>; + interrupts = <0>; + }; + ethphy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc2>; + interrupts = <1>; + }; + ethphy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc2>; + interrupts = <2>; + }; + ethphy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc2>; + interrupts = <3>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@29 { + compatible = "realtek,rtl8365mb"; + reg = <29>; + + reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; + + switch_intc3: interrupt-controller { + interrupt-parent = <&gpio0>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@7 { + reg = <7>; + ethernet = <ðernet>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; |