diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/fsl-tsec-phy.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/fsl-tsec-phy.txt | 89 |
1 files changed, 89 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt new file mode 100644 index 000000000..047bdf7bd --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,89 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node in booting-without-of.txt for an example +of how to define a PHY. + +Required properties: + - reg : Offset and length of the register set for the device, and optionally + the offset and length of the TBIPA register (TBI PHY address + register). If TBIPA register is not specified, the driver will + attempt to infer it from the register set specified (your mileage may + vary). + - compatible : Should define the compatible device type for the + mdio. Currently supported strings/devices are: + - "fsl,gianfar-tbi" + - "fsl,gianfar-mdio" + - "fsl,etsec2-tbi" + - "fsl,etsec2-mdio" + - "fsl,ucc-mdio" + - "fsl,fman-mdio" + When device_type is "mdio", the following strings are also considered: + - "gianfar" + - "ucc_geth_phy" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". +The TBI PHYs underneath them are similar to normal PHYs, but the reg property +is considered instructive, rather than descriptive. The reg property should +be chosen so it doesn't interfere with other PHYs on the bus. + +* Gianfar-compatible ethernet nodes + +Properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - interrupts : For FEC devices, the first interrupt is the device's + interrupt. For TSEC and eTSEC devices, the first interrupt is + transmit, the second is receive, and the third is error. + - phy-handle : See ethernet.txt file in the same directory. + - fixed-link : See fixed-link.txt in the same directory. + - phy-connection-type : See ethernet.txt file in the same directory. + This property is only really needed if the connection is of type + "rgmii-id", as all other connection types are detected by hardware. + - fsl,magic-packet : If present, indicates that the hardware supports + waking up via magic packet. + - fsl,wake-on-filer : If present, indicates that the hardware supports + waking up by Filer General Purpose Interrupt (FGPI) asserted on the + Rx int line. This is an advanced power management capability allowing + certain packet types (user) defined by filer rules to wake up the system. + - bd-stash : If present, indicates that the hardware supports stashing + buffer descriptors in the L2. + - rx-stash-len : Denotes the number of bytes of a received buffer to stash + in the L2. + - rx-stash-idx : Denotes the index of the first byte from the received + buffer to stash in the L2. + +Example: + ethernet@24000 { + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0> + }; + +* Gianfar PTP clock nodes + +Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt |