diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/xilinx_axienet.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/xilinx_axienet.txt | 99 |
1 files changed, 99 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt new file mode 100644 index 000000000..1aa4c6006 --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -0,0 +1,99 @@ +XILINX AXI ETHERNET Device Tree Bindings +-------------------------------------------------------- + +Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core +provides connectivity to an external ethernet PHY supporting different +interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two +segments of memory for buffering TX and RX, as well as the capability of +offloading TX/RX checksum calculation off the processor. + +Management configuration is done through the AXI interface, while payload is +sent and received through means of an AXI DMA controller. This driver +includes the DMA driver code, so this driver is incompatible with AXI DMA +driver. + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Must be one of "xlnx,axi-ethernet-1.00.a", + "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" +- reg : Address and length of the IO space, as well as the address + and length of the AXI DMA controller IO space, unless + axistream-connected is specified, in which case the reg + attribute of the node referenced by it is used. +- interrupts : Should be a list of 2 or 3 interrupts: TX DMA, RX DMA, + and optionally Ethernet core. If axistream-connected is + specified, the TX/RX DMA interrupts should be on that node + instead, and only the Ethernet core interrupt is optionally + specified here. +- phy-handle : Should point to the external phy device if exists. Pointing + this to the PCS/PMA PHY is deprecated and should be avoided. + See ethernet.txt file in the same directory. +- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware + +Optional properties: +- phy-mode : See ethernet.txt +- xlnx,phy-type : Deprecated, do not use, but still accepted in preference + to phy-mode. +- xlnx,txcsum : 0 or empty for disabling TX checksum offload, + 1 to enable partial TX checksum offload, + 2 to enable full TX checksum offload +- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload +- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to + support both 1000BaseX and SGMII modes. If set, the phy-mode + should be set to match the mode selected on core reset (i.e. + by the basex_or_sgmii core input line). +- clock-names: Tuple listing input clock names. Possible clocks: + s_axi_lite_clk: Clock for AXI register slave interface + axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces + ref_clk: Ethernet reference clock, used by signal delay + primitives and transceivers + mgt_clk: MGT reference clock (used by optional internal + PCS/PMA PHY) + + Note that if s_axi_lite_clk is not specified by name, the + first clock of any name is used for this. If that is also not + specified, the clock rate is auto-detected from the CPU clock + (but only on platforms where this is possible). New device + trees should specify all applicable clocks by name - the + fallbacks to an unnamed clock or to CPU clock are only for + backward compatibility. +- clocks: Phandles to input clocks matching clock-names. Refer to common + clock bindings. +- axistream-connected: Reference to another node which contains the resources + for the AXI DMA controller used by this device. + If this is specified, the DMA-related resources from that + device (DMA registers and DMA TX/RX interrupts) rather + than this one will be used. + - mdio : Child node for MDIO bus. Must be defined if PHY access is + required through the core's MDIO interface (i.e. always, + unless the PHY is accessed through a different bus). + + - pcs-handle: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X + modes, where "pcs-handle" should be used to point + to the PCS/PMA PHY, and "phy-handle" should point to an + external PHY if exists. + +Example: + axi_ethernet_eth: ethernet@40c00000 { + compatible = "xlnx,axi-ethernet-1.00.a"; + device_type = "network"; + interrupt-parent = <µblaze_0_axi_intc>; + interrupts = <2 0 1>; + clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk"; + clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; + phy-mode = "mii"; + reg = <0x40c00000 0x40000 0x50c00000 0x40000>; + xlnx,rxcsum = <0x2>; + xlnx,rxmem = <0x800>; + xlnx,txcsum = <0x2>; + phy-handle = <&phy0>; + axi_ethernetlite_0_mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: phy@0 { + device_type = "ethernet-phy"; + reg = <1>; + }; + }; + }; |