summaryrefslogtreecommitdiffstats
path: root/drivers/clk/bcm/clk-iproc.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/clk/bcm/clk-iproc.h')
-rw-r--r--drivers/clk/bcm/clk-iproc.h214
1 files changed, 214 insertions, 0 deletions
diff --git a/drivers/clk/bcm/clk-iproc.h b/drivers/clk/bcm/clk-iproc.h
new file mode 100644
index 000000000..0151d6ae1
--- /dev/null
+++ b/drivers/clk/bcm/clk-iproc.h
@@ -0,0 +1,214 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2014 Broadcom Corporation */
+
+#ifndef _CLK_IPROC_H
+#define _CLK_IPROC_H
+
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/of.h>
+#include <linux/clk-provider.h>
+
+#define IPROC_CLK_NAME_LEN 25
+#define IPROC_CLK_INVALID_OFFSET 0xffffffff
+#define bit_mask(width) ((1 << (width)) - 1)
+
+/* clocks that should not be disabled at runtime */
+#define IPROC_CLK_AON BIT(0)
+
+/* PLL that requires gating through ASIU */
+#define IPROC_CLK_PLL_ASIU BIT(1)
+
+/* PLL that has fractional part of the NDIV */
+#define IPROC_CLK_PLL_HAS_NDIV_FRAC BIT(2)
+
+/*
+ * Some of the iProc PLL/clocks may have an ASIC bug that requires read back
+ * of the same register following the write to flush the write transaction into
+ * the intended register
+ */
+#define IPROC_CLK_NEEDS_READ_BACK BIT(3)
+
+/*
+ * Some PLLs require the PLL SW override bit to be set before changes can be
+ * applied to the PLL
+ */
+#define IPROC_CLK_PLL_NEEDS_SW_CFG BIT(4)
+
+/*
+ * Some PLLs use a different way to control clock power, via the PWRDWN bit in
+ * the PLL control register
+ */
+#define IPROC_CLK_EMBED_PWRCTRL BIT(5)
+
+/*
+ * Some PLLs have separate registers for Status and Control. Identify this to
+ * let the driver know if additional registers need to be used
+ */
+#define IPROC_CLK_PLL_SPLIT_STAT_CTRL BIT(6)
+
+/*
+ * Some PLLs have an additional divide by 2 in master clock calculation;
+ * MCLK = VCO_freq / (Mdiv * 2). Identify this to let the driver know
+ * of modified calculations
+ */
+#define IPROC_CLK_MCLK_DIV_BY_2 BIT(7)
+
+/*
+ * Some PLLs provide a look up table for the leaf clock frequencies and
+ * auto calculates VCO frequency parameters based on the provided leaf
+ * clock frequencies. They have a user mode that allows the divider
+ * controls to be determined by the user
+ */
+#define IPROC_CLK_PLL_USER_MODE_ON BIT(8)
+
+/*
+ * Some PLLs have an active low reset
+ */
+#define IPROC_CLK_PLL_RESET_ACTIVE_LOW BIT(9)
+
+/*
+ * Calculate the PLL parameters are runtime, instead of using table
+ */
+#define IPROC_CLK_PLL_CALC_PARAM BIT(10)
+
+/*
+ * Parameters for VCO frequency configuration
+ *
+ * VCO frequency =
+ * ((ndiv_int + ndiv_frac / 2^20) * (ref frequency / pdiv)
+ */
+struct iproc_pll_vco_param {
+ unsigned long rate;
+ unsigned int ndiv_int;
+ unsigned int ndiv_frac;
+ unsigned int pdiv;
+};
+
+struct iproc_clk_reg_op {
+ unsigned int offset;
+ unsigned int shift;
+ unsigned int width;
+};
+
+/*
+ * Clock gating control at the top ASIU level
+ */
+struct iproc_asiu_gate {
+ unsigned int offset;
+ unsigned int en_shift;
+};
+
+/*
+ * Control of powering on/off of a PLL
+ *
+ * Before powering off a PLL, input isolation (ISO) needs to be enabled
+ */
+struct iproc_pll_aon_pwr_ctrl {
+ unsigned int offset;
+ unsigned int pwr_width;
+ unsigned int pwr_shift;
+ unsigned int iso_shift;
+};
+
+/*
+ * Control of the PLL reset
+ */
+struct iproc_pll_reset_ctrl {
+ unsigned int offset;
+ unsigned int reset_shift;
+ unsigned int p_reset_shift;
+};
+
+/*
+ * Control of the Ki, Kp, and Ka parameters
+ */
+struct iproc_pll_dig_filter_ctrl {
+ unsigned int offset;
+ unsigned int ki_shift;
+ unsigned int ki_width;
+ unsigned int kp_shift;
+ unsigned int kp_width;
+ unsigned int ka_shift;
+ unsigned int ka_width;
+};
+
+/*
+ * To enable SW control of the PLL
+ */
+struct iproc_pll_sw_ctrl {
+ unsigned int offset;
+ unsigned int shift;
+};
+
+struct iproc_pll_vco_ctrl {
+ unsigned int u_offset;
+ unsigned int l_offset;
+};
+
+/*
+ * Main PLL control parameters
+ */
+struct iproc_pll_ctrl {
+ unsigned long flags;
+ struct iproc_pll_aon_pwr_ctrl aon;
+ struct iproc_asiu_gate asiu;
+ struct iproc_pll_reset_ctrl reset;
+ struct iproc_pll_dig_filter_ctrl dig_filter;
+ struct iproc_pll_sw_ctrl sw_ctrl;
+ struct iproc_clk_reg_op ndiv_int;
+ struct iproc_clk_reg_op ndiv_frac;
+ struct iproc_clk_reg_op pdiv;
+ struct iproc_pll_vco_ctrl vco_ctrl;
+ struct iproc_clk_reg_op status;
+ struct iproc_clk_reg_op macro_mode;
+};
+
+/*
+ * Controls enabling/disabling a PLL derived clock
+ */
+struct iproc_clk_enable_ctrl {
+ unsigned int offset;
+ unsigned int enable_shift;
+ unsigned int hold_shift;
+ unsigned int bypass_shift;
+};
+
+/*
+ * Main clock control parameters for clocks derived from the PLLs
+ */
+struct iproc_clk_ctrl {
+ unsigned int channel;
+ unsigned long flags;
+ struct iproc_clk_enable_ctrl enable;
+ struct iproc_clk_reg_op mdiv;
+};
+
+/*
+ * Divisor of the ASIU clocks
+ */
+struct iproc_asiu_div {
+ unsigned int offset;
+ unsigned int en_shift;
+ unsigned int high_shift;
+ unsigned int high_width;
+ unsigned int low_shift;
+ unsigned int low_width;
+};
+
+void iproc_armpll_setup(struct device_node *node);
+void iproc_pll_clk_setup(struct device_node *node,
+ const struct iproc_pll_ctrl *pll_ctrl,
+ const struct iproc_pll_vco_param *vco,
+ unsigned int num_vco_entries,
+ const struct iproc_clk_ctrl *clk_ctrl,
+ unsigned int num_clks);
+void iproc_asiu_setup(struct device_node *node,
+ const struct iproc_asiu_div *div,
+ const struct iproc_asiu_gate *gate,
+ unsigned int num_clks);
+
+#endif /* _CLK_IPROC_H */