summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/igb/e1000_mac.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/intel/igb/e1000_mac.c')
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_mac.c1685
1 files changed, 1685 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_mac.c b/drivers/net/ethernet/intel/igb/e1000_mac.c
new file mode 100644
index 000000000..caf91c6f5
--- /dev/null
+++ b/drivers/net/ethernet/intel/igb/e1000_mac.c
@@ -0,0 +1,1685 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright(c) 2007 - 2018 Intel Corporation. */
+
+#include <linux/if_ether.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+
+#include "e1000_mac.h"
+
+#include "igb.h"
+
+static s32 igb_set_default_fc(struct e1000_hw *hw);
+static void igb_set_fc_watermarks(struct e1000_hw *hw);
+
+/**
+ * igb_get_bus_info_pcie - Get PCIe bus information
+ * @hw: pointer to the HW structure
+ *
+ * Determines and stores the system bus information for a particular
+ * network interface. The following bus information is determined and stored:
+ * bus speed, bus width, type (PCIe), and PCIe function.
+ **/
+s32 igb_get_bus_info_pcie(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ s32 ret_val;
+ u32 reg;
+ u16 pcie_link_status;
+
+ bus->type = e1000_bus_type_pci_express;
+
+ ret_val = igb_read_pcie_cap_reg(hw,
+ PCI_EXP_LNKSTA,
+ &pcie_link_status);
+ if (ret_val) {
+ bus->width = e1000_bus_width_unknown;
+ bus->speed = e1000_bus_speed_unknown;
+ } else {
+ switch (pcie_link_status & PCI_EXP_LNKSTA_CLS) {
+ case PCI_EXP_LNKSTA_CLS_2_5GB:
+ bus->speed = e1000_bus_speed_2500;
+ break;
+ case PCI_EXP_LNKSTA_CLS_5_0GB:
+ bus->speed = e1000_bus_speed_5000;
+ break;
+ default:
+ bus->speed = e1000_bus_speed_unknown;
+ break;
+ }
+
+ bus->width = (enum e1000_bus_width)((pcie_link_status &
+ PCI_EXP_LNKSTA_NLW) >>
+ PCI_EXP_LNKSTA_NLW_SHIFT);
+ }
+
+ reg = rd32(E1000_STATUS);
+ bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT;
+
+ return 0;
+}
+
+/**
+ * igb_clear_vfta - Clear VLAN filter table
+ * @hw: pointer to the HW structure
+ *
+ * Clears the register array which contains the VLAN filter table by
+ * setting all the values to 0.
+ **/
+void igb_clear_vfta(struct e1000_hw *hw)
+{
+ u32 offset;
+
+ for (offset = E1000_VLAN_FILTER_TBL_SIZE; offset--;)
+ hw->mac.ops.write_vfta(hw, offset, 0);
+}
+
+/**
+ * igb_write_vfta - Write value to VLAN filter table
+ * @hw: pointer to the HW structure
+ * @offset: register offset in VLAN filter table
+ * @value: register value written to VLAN filter table
+ *
+ * Writes value at the given offset in the register array which stores
+ * the VLAN filter table.
+ **/
+void igb_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ struct igb_adapter *adapter = hw->back;
+
+ array_wr32(E1000_VFTA, offset, value);
+ wrfl();
+
+ adapter->shadow_vfta[offset] = value;
+}
+
+/**
+ * igb_init_rx_addrs - Initialize receive address's
+ * @hw: pointer to the HW structure
+ * @rar_count: receive address registers
+ *
+ * Setups the receive address registers by setting the base receive address
+ * register to the devices MAC address and clearing all the other receive
+ * address registers to 0.
+ **/
+void igb_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
+{
+ u32 i;
+ u8 mac_addr[ETH_ALEN] = {0};
+
+ /* Setup the receive address */
+ hw_dbg("Programming MAC Address into RAR[0]\n");
+
+ hw->mac.ops.rar_set(hw, hw->mac.addr, 0);
+
+ /* Zero out the other (rar_entry_count - 1) receive addresses */
+ hw_dbg("Clearing RAR[1-%u]\n", rar_count-1);
+ for (i = 1; i < rar_count; i++)
+ hw->mac.ops.rar_set(hw, mac_addr, i);
+}
+
+/**
+ * igb_find_vlvf_slot - find the VLAN id or the first empty slot
+ * @hw: pointer to hardware structure
+ * @vlan: VLAN id to write to VLAN filter
+ * @vlvf_bypass: skip VLVF if no match is found
+ *
+ * return the VLVF index where this VLAN id should be placed
+ *
+ **/
+static s32 igb_find_vlvf_slot(struct e1000_hw *hw, u32 vlan, bool vlvf_bypass)
+{
+ s32 regindex, first_empty_slot;
+ u32 bits;
+
+ /* short cut the special case */
+ if (vlan == 0)
+ return 0;
+
+ /* if vlvf_bypass is set we don't want to use an empty slot, we
+ * will simply bypass the VLVF if there are no entries present in the
+ * VLVF that contain our VLAN
+ */
+ first_empty_slot = vlvf_bypass ? -E1000_ERR_NO_SPACE : 0;
+
+ /* Search for the VLAN id in the VLVF entries. Save off the first empty
+ * slot found along the way.
+ *
+ * pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1
+ */
+ for (regindex = E1000_VLVF_ARRAY_SIZE; --regindex > 0;) {
+ bits = rd32(E1000_VLVF(regindex)) & E1000_VLVF_VLANID_MASK;
+ if (bits == vlan)
+ return regindex;
+ if (!first_empty_slot && !bits)
+ first_empty_slot = regindex;
+ }
+
+ return first_empty_slot ? : -E1000_ERR_NO_SPACE;
+}
+
+/**
+ * igb_vfta_set - enable or disable vlan in VLAN filter table
+ * @hw: pointer to the HW structure
+ * @vlan: VLAN id to add or remove
+ * @vind: VMDq output index that maps queue to VLAN id
+ * @vlan_on: if true add filter, if false remove
+ * @vlvf_bypass: skip VLVF if no match is found
+ *
+ * Sets or clears a bit in the VLAN filter table array based on VLAN id
+ * and if we are adding or removing the filter
+ **/
+s32 igb_vfta_set(struct e1000_hw *hw, u32 vlan, u32 vind,
+ bool vlan_on, bool vlvf_bypass)
+{
+ struct igb_adapter *adapter = hw->back;
+ u32 regidx, vfta_delta, vfta, bits;
+ s32 vlvf_index;
+
+ if ((vlan > 4095) || (vind > 7))
+ return -E1000_ERR_PARAM;
+
+ /* this is a 2 part operation - first the VFTA, then the
+ * VLVF and VLVFB if VT Mode is set
+ * We don't write the VFTA until we know the VLVF part succeeded.
+ */
+
+ /* Part 1
+ * The VFTA is a bitstring made up of 128 32-bit registers
+ * that enable the particular VLAN id, much like the MTA:
+ * bits[11-5]: which register
+ * bits[4-0]: which bit in the register
+ */
+ regidx = vlan / 32;
+ vfta_delta = BIT(vlan % 32);
+ vfta = adapter->shadow_vfta[regidx];
+
+ /* vfta_delta represents the difference between the current value
+ * of vfta and the value we want in the register. Since the diff
+ * is an XOR mask we can just update vfta using an XOR.
+ */
+ vfta_delta &= vlan_on ? ~vfta : vfta;
+ vfta ^= vfta_delta;
+
+ /* Part 2
+ * If VT Mode is set
+ * Either vlan_on
+ * make sure the VLAN is in VLVF
+ * set the vind bit in the matching VLVFB
+ * Or !vlan_on
+ * clear the pool bit and possibly the vind
+ */
+ if (!adapter->vfs_allocated_count)
+ goto vfta_update;
+
+ vlvf_index = igb_find_vlvf_slot(hw, vlan, vlvf_bypass);
+ if (vlvf_index < 0) {
+ if (vlvf_bypass)
+ goto vfta_update;
+ return vlvf_index;
+ }
+
+ bits = rd32(E1000_VLVF(vlvf_index));
+
+ /* set the pool bit */
+ bits |= BIT(E1000_VLVF_POOLSEL_SHIFT + vind);
+ if (vlan_on)
+ goto vlvf_update;
+
+ /* clear the pool bit */
+ bits ^= BIT(E1000_VLVF_POOLSEL_SHIFT + vind);
+
+ if (!(bits & E1000_VLVF_POOLSEL_MASK)) {
+ /* Clear VFTA first, then disable VLVF. Otherwise
+ * we run the risk of stray packets leaking into
+ * the PF via the default pool
+ */
+ if (vfta_delta)
+ hw->mac.ops.write_vfta(hw, regidx, vfta);
+
+ /* disable VLVF and clear remaining bit from pool */
+ wr32(E1000_VLVF(vlvf_index), 0);
+
+ return 0;
+ }
+
+ /* If there are still bits set in the VLVFB registers
+ * for the VLAN ID indicated we need to see if the
+ * caller is requesting that we clear the VFTA entry bit.
+ * If the caller has requested that we clear the VFTA
+ * entry bit but there are still pools/VFs using this VLAN
+ * ID entry then ignore the request. We're not worried
+ * about the case where we're turning the VFTA VLAN ID
+ * entry bit on, only when requested to turn it off as
+ * there may be multiple pools and/or VFs using the
+ * VLAN ID entry. In that case we cannot clear the
+ * VFTA bit until all pools/VFs using that VLAN ID have also
+ * been cleared. This will be indicated by "bits" being
+ * zero.
+ */
+ vfta_delta = 0;
+
+vlvf_update:
+ /* record pool change and enable VLAN ID if not already enabled */
+ wr32(E1000_VLVF(vlvf_index), bits | vlan | E1000_VLVF_VLANID_ENABLE);
+
+vfta_update:
+ /* bit was set/cleared before we started */
+ if (vfta_delta)
+ hw->mac.ops.write_vfta(hw, regidx, vfta);
+
+ return 0;
+}
+
+/**
+ * igb_check_alt_mac_addr - Check for alternate MAC addr
+ * @hw: pointer to the HW structure
+ *
+ * Checks the nvm for an alternate MAC address. An alternate MAC address
+ * can be setup by pre-boot software and must be treated like a permanent
+ * address and must override the actual permanent MAC address. If an
+ * alternate MAC address is found it is saved in the hw struct and
+ * programmed into RAR0 and the function returns success, otherwise the
+ * function returns an error.
+ **/
+s32 igb_check_alt_mac_addr(struct e1000_hw *hw)
+{
+ u32 i;
+ s32 ret_val = 0;
+ u16 offset, nvm_alt_mac_addr_offset, nvm_data;
+ u8 alt_mac_addr[ETH_ALEN];
+
+ /* Alternate MAC address is handled by the option ROM for 82580
+ * and newer. SW support not required.
+ */
+ if (hw->mac.type >= e1000_82580)
+ goto out;
+
+ ret_val = hw->nvm.ops.read(hw, NVM_ALT_MAC_ADDR_PTR, 1,
+ &nvm_alt_mac_addr_offset);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if ((nvm_alt_mac_addr_offset == 0xFFFF) ||
+ (nvm_alt_mac_addr_offset == 0x0000))
+ /* There is no Alternate MAC Address */
+ goto out;
+
+ if (hw->bus.func == E1000_FUNC_1)
+ nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN1;
+ if (hw->bus.func == E1000_FUNC_2)
+ nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN2;
+
+ if (hw->bus.func == E1000_FUNC_3)
+ nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN3;
+ for (i = 0; i < ETH_ALEN; i += 2) {
+ offset = nvm_alt_mac_addr_offset + (i >> 1);
+ ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ alt_mac_addr[i] = (u8)(nvm_data & 0xFF);
+ alt_mac_addr[i + 1] = (u8)(nvm_data >> 8);
+ }
+
+ /* if multicast bit is set, the alternate address will not be used */
+ if (is_multicast_ether_addr(alt_mac_addr)) {
+ hw_dbg("Ignoring Alternate Mac Address with MC bit set\n");
+ goto out;
+ }
+
+ /* We have a valid alternate MAC address, and we want to treat it the
+ * same as the normal permanent MAC address stored by the HW into the
+ * RAR. Do this by mapping this address into RAR0.
+ */
+ hw->mac.ops.rar_set(hw, alt_mac_addr, 0);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_rar_set - Set receive address register
+ * @hw: pointer to the HW structure
+ * @addr: pointer to the receive address
+ * @index: receive address array register
+ *
+ * Sets the receive address array register at index to the address passed
+ * in by addr.
+ **/
+void igb_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ /* HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] |
+ ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ /* If MAC address zero, no need to set the AV bit */
+ if (rar_low || rar_high)
+ rar_high |= E1000_RAH_AV;
+
+ /* Some bridges will combine consecutive 32-bit writes into
+ * a single burst write, which will malfunction on some parts.
+ * The flushes avoid this.
+ */
+ wr32(E1000_RAL(index), rar_low);
+ wrfl();
+ wr32(E1000_RAH(index), rar_high);
+ wrfl();
+}
+
+/**
+ * igb_mta_set - Set multicast filter table address
+ * @hw: pointer to the HW structure
+ * @hash_value: determines the MTA register and bit to set
+ *
+ * The multicast table address is a register array of 32-bit registers.
+ * The hash_value is used to determine what register the bit is in, the
+ * current value is read, the new bit is OR'd in and the new value is
+ * written back into the register.
+ **/
+void igb_mta_set(struct e1000_hw *hw, u32 hash_value)
+{
+ u32 hash_bit, hash_reg, mta;
+
+ /* The MTA is a register array of 32-bit registers. It is
+ * treated like an array of (32*mta_reg_count) bits. We want to
+ * set bit BitArray[hash_value]. So we figure out what register
+ * the bit is in, read it, OR in the new bit, then write
+ * back the new value. The (hw->mac.mta_reg_count - 1) serves as a
+ * mask to bits 31:5 of the hash value which gives us the
+ * register we're modifying. The hash bit within that register
+ * is determined by the lower 5 bits of the hash value.
+ */
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ mta = array_rd32(E1000_MTA, hash_reg);
+
+ mta |= BIT(hash_bit);
+
+ array_wr32(E1000_MTA, hash_reg, mta);
+ wrfl();
+}
+
+/**
+ * igb_hash_mc_addr - Generate a multicast hash value
+ * @hw: pointer to the HW structure
+ * @mc_addr: pointer to a multicast address
+ *
+ * Generates a multicast address hash value which is used to determine
+ * the multicast filter table array address and new table value. See
+ * igb_mta_set()
+ **/
+static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+{
+ u32 hash_value, hash_mask;
+ u8 bit_shift = 1;
+
+ /* Register count multiplied by bits per register */
+ hash_mask = (hw->mac.mta_reg_count * 32) - 1;
+
+ /* For a mc_filter_type of 0, bit_shift is the number of left-shifts
+ * where 0xFF would still fall within the hash mask.
+ */
+ while (hash_mask >> bit_shift != 0xFF && bit_shift < 4)
+ bit_shift++;
+
+ /* The portion of the address that is used for the hash table
+ * is determined by the mc_filter_type setting.
+ * The algorithm is such that there is a total of 8 bits of shifting.
+ * The bit_shift for a mc_filter_type of 0 represents the number of
+ * left-shifts where the MSB of mc_addr[5] would still fall within
+ * the hash_mask. Case 0 does this exactly. Since there are a total
+ * of 8 bits of shifting, then mc_addr[4] will shift right the
+ * remaining number of bits. Thus 8 - bit_shift. The rest of the
+ * cases are a variation of this algorithm...essentially raising the
+ * number of bits to shift mc_addr[5] left, while still keeping the
+ * 8-bit shifting total.
+ *
+ * For example, given the following Destination MAC Address and an
+ * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask),
+ * we can see that the bit_shift for case 0 is 4. These are the hash
+ * values resulting from each mc_filter_type...
+ * [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ *
+ * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563
+ * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6
+ * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163
+ * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634
+ */
+ switch (hw->mac.mc_filter_type) {
+ default:
+ case 0:
+ break;
+ case 1:
+ bit_shift += 1;
+ break;
+ case 2:
+ bit_shift += 2;
+ break;
+ case 3:
+ bit_shift += 4;
+ break;
+ }
+
+ hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) |
+ (((u16) mc_addr[5]) << bit_shift)));
+
+ return hash_value;
+}
+
+/**
+ * igb_i21x_hw_doublecheck - double checks potential HW issue in i21X
+ * @hw: pointer to the HW structure
+ *
+ * Checks if multicast array is wrote correctly
+ * If not then rewrites again to register
+ **/
+static void igb_i21x_hw_doublecheck(struct e1000_hw *hw)
+{
+ int failed_cnt = 3;
+ bool is_failed;
+ int i;
+
+ do {
+ is_failed = false;
+ for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) {
+ if (array_rd32(E1000_MTA, i) != hw->mac.mta_shadow[i]) {
+ is_failed = true;
+ array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
+ wrfl();
+ }
+ }
+ if (is_failed && --failed_cnt <= 0) {
+ hw_dbg("Failed to update MTA_REGISTER, too many retries");
+ break;
+ }
+ } while (is_failed);
+}
+
+/**
+ * igb_update_mc_addr_list - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ *
+ * Updates entire Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+void igb_update_mc_addr_list(struct e1000_hw *hw,
+ u8 *mc_addr_list, u32 mc_addr_count)
+{
+ u32 hash_value, hash_bit, hash_reg;
+ int i;
+
+ /* clear mta_shadow */
+ memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
+
+ /* update mta_shadow from mc_addr_list */
+ for (i = 0; (u32) i < mc_addr_count; i++) {
+ hash_value = igb_hash_mc_addr(hw, mc_addr_list);
+
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ hw->mac.mta_shadow[hash_reg] |= BIT(hash_bit);
+ mc_addr_list += (ETH_ALEN);
+ }
+
+ /* replace the entire MTA table */
+ for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
+ array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
+ wrfl();
+ if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211)
+ igb_i21x_hw_doublecheck(hw);
+}
+
+/**
+ * igb_clear_hw_cntrs_base - Clear base hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the base hardware counters by reading the counter registers.
+ **/
+void igb_clear_hw_cntrs_base(struct e1000_hw *hw)
+{
+ rd32(E1000_CRCERRS);
+ rd32(E1000_SYMERRS);
+ rd32(E1000_MPC);
+ rd32(E1000_SCC);
+ rd32(E1000_ECOL);
+ rd32(E1000_MCC);
+ rd32(E1000_LATECOL);
+ rd32(E1000_COLC);
+ rd32(E1000_DC);
+ rd32(E1000_SEC);
+ rd32(E1000_RLEC);
+ rd32(E1000_XONRXC);
+ rd32(E1000_XONTXC);
+ rd32(E1000_XOFFRXC);
+ rd32(E1000_XOFFTXC);
+ rd32(E1000_FCRUC);
+ rd32(E1000_GPRC);
+ rd32(E1000_BPRC);
+ rd32(E1000_MPRC);
+ rd32(E1000_GPTC);
+ rd32(E1000_GORCL);
+ rd32(E1000_GORCH);
+ rd32(E1000_GOTCL);
+ rd32(E1000_GOTCH);
+ rd32(E1000_RNBC);
+ rd32(E1000_RUC);
+ rd32(E1000_RFC);
+ rd32(E1000_ROC);
+ rd32(E1000_RJC);
+ rd32(E1000_TORL);
+ rd32(E1000_TORH);
+ rd32(E1000_TOTL);
+ rd32(E1000_TOTH);
+ rd32(E1000_TPR);
+ rd32(E1000_TPT);
+ rd32(E1000_MPTC);
+ rd32(E1000_BPTC);
+}
+
+/**
+ * igb_check_for_copper_link - Check for link (Copper)
+ * @hw: pointer to the HW structure
+ *
+ * Checks to see of the link status of the hardware has changed. If a
+ * change in link status has been detected, then we read the PHY registers
+ * to get the current speed/duplex if link exists.
+ **/
+s32 igb_check_for_copper_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ bool link;
+
+ /* We only want to go out to the PHY registers to see if Auto-Neg
+ * has completed and/or if our link status has changed. The
+ * get_link_status flag is set upon receiving a Link Status
+ * Change or Rx Sequence Error interrupt.
+ */
+ if (!mac->get_link_status) {
+ ret_val = 0;
+ goto out;
+ }
+
+ /* First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ */
+ ret_val = igb_phy_has_link(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ goto out; /* No link detected */
+
+ mac->get_link_status = false;
+
+ /* Check if there was DownShift, must be checked
+ * immediately after link-up
+ */
+ igb_check_downshift(hw);
+
+ /* If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!mac->autoneg) {
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ /* Auto-Neg is enabled. Auto Speed Detection takes care
+ * of MAC speed/duplex configuration. So we only need to
+ * configure Collision Distance in the MAC.
+ */
+ igb_config_collision_dist(hw);
+
+ /* Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = igb_config_fc_after_link_up(hw);
+ if (ret_val)
+ hw_dbg("Error configuring flow control\n");
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_setup_link - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+s32 igb_setup_link(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+
+ /* In the case of the phy reset being blocked, we already have a link.
+ * We do not need to set it up again.
+ */
+ if (igb_check_reset_block(hw))
+ goto out;
+
+ /* If requested flow control is set to default, set flow control
+ * based on the EEPROM flow control settings.
+ */
+ if (hw->fc.requested_mode == e1000_fc_default) {
+ ret_val = igb_set_default_fc(hw);
+ if (ret_val)
+ goto out;
+ }
+
+ /* We want to save off the original Flow Control configuration just
+ * in case we get disconnected and then reconnected into a different
+ * hub or switch with different Flow Control capabilities.
+ */
+ hw->fc.current_mode = hw->fc.requested_mode;
+
+ hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode);
+
+ /* Call the necessary media_type subroutine to configure the link. */
+ ret_val = hw->mac.ops.setup_physical_interface(hw);
+ if (ret_val)
+ goto out;
+
+ /* Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ hw_dbg("Initializing the Flow Control address, type and timer regs\n");
+ wr32(E1000_FCT, FLOW_CONTROL_TYPE);
+ wr32(E1000_FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ wr32(E1000_FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ wr32(E1000_FCTTV, hw->fc.pause_time);
+
+ igb_set_fc_watermarks(hw);
+
+out:
+
+ return ret_val;
+}
+
+/**
+ * igb_config_collision_dist - Configure collision distance
+ * @hw: pointer to the HW structure
+ *
+ * Configures the collision distance to the default value and is used
+ * during link setup. Currently no func pointer exists and all
+ * implementations are handled in the generic version of this function.
+ **/
+void igb_config_collision_dist(struct e1000_hw *hw)
+{
+ u32 tctl;
+
+ tctl = rd32(E1000_TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+
+ wr32(E1000_TCTL, tctl);
+ wrfl();
+}
+
+/**
+ * igb_set_fc_watermarks - Set flow control high/low watermarks
+ * @hw: pointer to the HW structure
+ *
+ * Sets the flow control high/low threshold (watermark) registers. If
+ * flow control XON frame transmission is enabled, then set XON frame
+ * tansmission as well.
+ **/
+static void igb_set_fc_watermarks(struct e1000_hw *hw)
+{
+ u32 fcrtl = 0, fcrth = 0;
+
+ /* Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames is not enabled, then these
+ * registers will be set to 0.
+ */
+ if (hw->fc.current_mode & e1000_fc_tx_pause) {
+ /* We need to set up the Receive Threshold high and low water
+ * marks as well as (optionally) enabling the transmission of
+ * XON frames.
+ */
+ fcrtl = hw->fc.low_water;
+ if (hw->fc.send_xon)
+ fcrtl |= E1000_FCRTL_XONE;
+
+ fcrth = hw->fc.high_water;
+ }
+ wr32(E1000_FCRTL, fcrtl);
+ wr32(E1000_FCRTH, fcrth);
+}
+
+/**
+ * igb_set_default_fc - Set flow control default values
+ * @hw: pointer to the HW structure
+ *
+ * Read the EEPROM for the default values for flow control and store the
+ * values.
+ **/
+static s32 igb_set_default_fc(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 lan_offset;
+ u16 nvm_data;
+
+ /* Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ if (hw->mac.type == e1000_i350)
+ lan_offset = NVM_82580_LAN_FUNC_OFFSET(hw->bus.func);
+ else
+ lan_offset = 0;
+
+ ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG + lan_offset,
+ 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc.requested_mode = e1000_fc_none;
+ else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == NVM_WORD0F_ASM_DIR)
+ hw->fc.requested_mode = e1000_fc_tx_pause;
+ else
+ hw->fc.requested_mode = e1000_fc_full;
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_force_mac_fc - Force the MAC's flow control settings
+ * @hw: pointer to the HW structure
+ *
+ * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the
+ * device control register to reflect the adapter settings. TFCE and RFCE
+ * need to be explicitly set by software when a copper PHY is used because
+ * autonegotiation is managed by the PHY rather than the MAC. Software must
+ * also configure these bits when link is forced on a fiber connection.
+ **/
+s32 igb_force_mac_fc(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val = 0;
+
+ ctrl = rd32(E1000_CTRL);
+
+ /* Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc.current_mode" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not receive pause frames).
+ * 3: Both Rx and TX flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+ hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
+
+ switch (hw->fc.current_mode) {
+ case e1000_fc_none:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case e1000_fc_rx_pause:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case e1000_fc_tx_pause:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case e1000_fc_full:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ hw_dbg("Flow control param set incorrectly\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ wr32(E1000_CTRL, ctrl);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_config_fc_after_link_up - Configures flow control after link
+ * @hw: pointer to the HW structure
+ *
+ * Checks the status of auto-negotiation after link up to ensure that the
+ * speed and duplex were not forced. If the link needed to be forced, then
+ * flow control needs to be forced also. If auto-negotiation is enabled
+ * and did not fail, then we configure flow control based on our link
+ * partner.
+ **/
+s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val = 0;
+ u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg;
+ u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
+ u16 speed, duplex;
+
+ /* Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (mac->autoneg_failed) {
+ if (hw->phy.media_type == e1000_media_type_internal_serdes)
+ ret_val = igb_force_mac_fc(hw);
+ } else {
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ret_val = igb_force_mac_fc(hw);
+ }
+
+ if (ret_val) {
+ hw_dbg("Error forcing flow control settings\n");
+ goto out;
+ }
+
+ /* Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) {
+ /* Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS,
+ &mii_status_reg);
+ if (ret_val)
+ goto out;
+ ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS,
+ &mii_status_reg);
+ if (ret_val)
+ goto out;
+
+ if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+ hw_dbg("Copper PHY and Auto Neg has not completed.\n");
+ goto out;
+ }
+
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (Address 4) and the Auto_Negotiation Base
+ * Page Ability Register (Address 5) to determine how
+ * flow control was negotiated.
+ */
+ ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if (ret_val)
+ goto out;
+ ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if (ret_val)
+ goto out;
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_fc_full
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /* Now we need to check if the user selected RX ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
+ hw_dbg("Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = RX PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_tx_pause;
+ hw_dbg("Flow Control = TX PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = RX PAUSE frames only.\n");
+ }
+ /* Per the IEEE spec, at this point flow control should be
+ * disabled. However, we want to consider that we could
+ * be connected to a legacy switch that doesn't advertise
+ * desired flow control, but can be forced on the link
+ * partner. So if we advertised no flow control, that is
+ * what we will resolve to. If we advertised some kind of
+ * receive capability (Rx Pause Only or Full Flow Control)
+ * and the link partner advertised none, we will configure
+ * ourselves to enable Rx Flow Control only. We can do
+ * this safely for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx, no
+ * harm done since we won't be receiving any PAUSE frames
+ * anyway. If the intent on the link partner was to have
+ * flow control enabled, then by us enabling RX only, we
+ * can at least receive pause frames and process them.
+ * This is a good idea because in most cases, since we are
+ * predominantly a server NIC, more times than not we will
+ * be asked to delay transmission of packets than asking
+ * our link partner to pause transmission of frames.
+ */
+ else if ((hw->fc.requested_mode == e1000_fc_none) ||
+ (hw->fc.requested_mode == e1000_fc_tx_pause) ||
+ (hw->fc.strict_ieee)) {
+ hw->fc.current_mode = e1000_fc_none;
+ hw_dbg("Flow Control = NONE.\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = RX PAUSE frames only.\n");
+ }
+
+ /* Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ hw_dbg("Error getting link speed and duplex\n");
+ goto out;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc.current_mode = e1000_fc_none;
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = igb_force_mac_fc(hw);
+ if (ret_val) {
+ hw_dbg("Error forcing flow control settings\n");
+ goto out;
+ }
+ }
+ /* Check for the case where we have SerDes media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_internal_serdes)
+ && mac->autoneg) {
+ /* Read the PCS_LSTS and check to see if AutoNeg
+ * has completed.
+ */
+ pcs_status_reg = rd32(E1000_PCS_LSTAT);
+
+ if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) {
+ hw_dbg("PCS Auto Neg has not completed.\n");
+ return ret_val;
+ }
+
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (PCS_ANADV) and the Auto_Negotiation Base
+ * Page Ability Register (PCS_LPAB) to determine how
+ * flow control was negotiated.
+ */
+ pcs_adv_reg = rd32(E1000_PCS_ANADV);
+ pcs_lp_ability_reg = rd32(E1000_PCS_LPAB);
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (PCS_ANADV) and two bits in the Auto Negotiation Base
+ * Page Ability Register (PCS_LPAB) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | e1000_fc_full
+ *
+ */
+ if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) {
+ /* Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise Rx
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
+ hw_dbg("Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = Rx PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ */
+ else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+ (pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_tx_pause;
+ hw_dbg("Flow Control = Tx PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ */
+ else if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+ !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = Rx PAUSE frames only.\n");
+ } else {
+ /* Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
+ hw->fc.current_mode = e1000_fc_none;
+ hw_dbg("Flow Control = NONE.\n");
+ }
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ pcs_ctrl_reg = rd32(E1000_PCS_LCTL);
+ pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+ wr32(E1000_PCS_LCTL, pcs_ctrl_reg);
+
+ ret_val = igb_force_mac_fc(hw);
+ if (ret_val) {
+ hw_dbg("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_speed_and_duplex_copper - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Read the status register for the current speed/duplex and store the current
+ * speed and duplex for copper connections.
+ **/
+s32 igb_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ u32 status;
+
+ status = rd32(E1000_STATUS);
+ if (status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ hw_dbg("1000 Mbs, ");
+ } else if (status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ hw_dbg("100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ hw_dbg("10 Mbs, ");
+ }
+
+ if (status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ hw_dbg("Full Duplex\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ hw_dbg("Half Duplex\n");
+ }
+
+ return 0;
+}
+
+/**
+ * igb_get_hw_semaphore - Acquire hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the HW semaphore to access the PHY or NVM
+ **/
+s32 igb_get_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+ s32 ret_val = 0;
+ s32 timeout = hw->nvm.word_size + 1;
+ s32 i = 0;
+
+ /* Get the SW semaphore */
+ while (i < timeout) {
+ swsm = rd32(E1000_SWSM);
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+
+ udelay(50);
+ i++;
+ }
+
+ if (i == timeout) {
+ hw_dbg("Driver can't access device - SMBI bit is set.\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+ /* Get the FW semaphore. */
+ for (i = 0; i < timeout; i++) {
+ swsm = rd32(E1000_SWSM);
+ wr32(E1000_SWSM, swsm | E1000_SWSM_SWESMBI);
+
+ /* Semaphore acquired if bit latched */
+ if (rd32(E1000_SWSM) & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ }
+
+ if (i == timeout) {
+ /* Release semaphores */
+ igb_put_hw_semaphore(hw);
+ hw_dbg("Driver can't access the NVM\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_put_hw_semaphore - Release hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Release hardware semaphore used to access the PHY or NVM
+ **/
+void igb_put_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+
+ swsm = rd32(E1000_SWSM);
+
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+
+ wr32(E1000_SWSM, swsm);
+}
+
+/**
+ * igb_get_auto_rd_done - Check for auto read completion
+ * @hw: pointer to the HW structure
+ *
+ * Check EEPROM for Auto Read done bit.
+ **/
+s32 igb_get_auto_rd_done(struct e1000_hw *hw)
+{
+ s32 i = 0;
+ s32 ret_val = 0;
+
+
+ while (i < AUTO_READ_DONE_TIMEOUT) {
+ if (rd32(E1000_EECD) & E1000_EECD_AUTO_RD)
+ break;
+ usleep_range(1000, 2000);
+ i++;
+ }
+
+ if (i == AUTO_READ_DONE_TIMEOUT) {
+ hw_dbg("Auto read by HW from NVM has not completed.\n");
+ ret_val = -E1000_ERR_RESET;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_valid_led_default - Verify a valid default LED config
+ * @hw: pointer to the HW structure
+ * @data: pointer to the NVM (EEPROM)
+ *
+ * Read the EEPROM for the current default LED configuration. If the
+ * LED configuration is not valid, set to a valid LED configuration.
+ **/
+static s32 igb_valid_led_default(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) {
+ switch (hw->phy.media_type) {
+ case e1000_media_type_internal_serdes:
+ *data = ID_LED_DEFAULT_82575_SERDES;
+ break;
+ case e1000_media_type_copper:
+ default:
+ *data = ID_LED_DEFAULT;
+ break;
+ }
+ }
+out:
+ return ret_val;
+}
+
+/**
+ * igb_id_led_init -
+ * @hw: pointer to the HW structure
+ *
+ **/
+s32 igb_id_led_init(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 data, i, temp;
+ const u16 led_mask = 0x0F;
+
+ /* i210 and i211 devices have different LED mechanism */
+ if ((hw->mac.type == e1000_i210) ||
+ (hw->mac.type == e1000_i211))
+ ret_val = igb_valid_led_default_i210(hw, &data);
+ else
+ ret_val = igb_valid_led_default(hw, &data);
+
+ if (ret_val)
+ goto out;
+
+ mac->ledctl_default = rd32(E1000_LEDCTL);
+ mac->ledctl_mode1 = mac->ledctl_default;
+ mac->ledctl_mode2 = mac->ledctl_default;
+
+ for (i = 0; i < 4; i++) {
+ temp = (data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_cleanup_led - Set LED config to default operation
+ * @hw: pointer to the HW structure
+ *
+ * Remove the current LED configuration and set the LED configuration
+ * to the default value, saved from the EEPROM.
+ **/
+s32 igb_cleanup_led(struct e1000_hw *hw)
+{
+ wr32(E1000_LEDCTL, hw->mac.ledctl_default);
+ return 0;
+}
+
+/**
+ * igb_blink_led - Blink LED
+ * @hw: pointer to the HW structure
+ *
+ * Blink the led's which are set to be on.
+ **/
+s32 igb_blink_led(struct e1000_hw *hw)
+{
+ u32 ledctl_blink = 0;
+ u32 i;
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ /* always blink LED0 for PCI-E fiber */
+ ledctl_blink = E1000_LEDCTL_LED0_BLINK |
+ (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
+ } else {
+ /* Set the blink bit for each LED that's "on" (0x0E)
+ * (or "off" if inverted) in ledctl_mode2. The blink
+ * logic in hardware only works when mode is set to "on"
+ * so it must be changed accordingly when the mode is
+ * "off" and inverted.
+ */
+ ledctl_blink = hw->mac.ledctl_mode2;
+ for (i = 0; i < 32; i += 8) {
+ u32 mode = (hw->mac.ledctl_mode2 >> i) &
+ E1000_LEDCTL_LED0_MODE_MASK;
+ u32 led_default = hw->mac.ledctl_default >> i;
+
+ if ((!(led_default & E1000_LEDCTL_LED0_IVRT) &&
+ (mode == E1000_LEDCTL_MODE_LED_ON)) ||
+ ((led_default & E1000_LEDCTL_LED0_IVRT) &&
+ (mode == E1000_LEDCTL_MODE_LED_OFF))) {
+ ledctl_blink &=
+ ~(E1000_LEDCTL_LED0_MODE_MASK << i);
+ ledctl_blink |= (E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_MODE_LED_ON) << i;
+ }
+ }
+ }
+
+ wr32(E1000_LEDCTL, ledctl_blink);
+
+ return 0;
+}
+
+/**
+ * igb_led_off - Turn LED off
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED off.
+ **/
+s32 igb_led_off(struct e1000_hw *hw)
+{
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ wr32(E1000_LEDCTL, hw->mac.ledctl_mode1);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * igb_disable_pcie_master - Disables PCI-express master access
+ * @hw: pointer to the HW structure
+ *
+ * Returns 0 (0) if successful, else returns -10
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
+ * the master requests to be disabled.
+ *
+ * Disables PCI-Express master access and verifies there are no pending
+ * requests.
+ **/
+s32 igb_disable_pcie_master(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 timeout = MASTER_DISABLE_TIMEOUT;
+ s32 ret_val = 0;
+
+ if (hw->bus.type != e1000_bus_type_pci_express)
+ goto out;
+
+ ctrl = rd32(E1000_CTRL);
+ ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
+ wr32(E1000_CTRL, ctrl);
+
+ while (timeout) {
+ if (!(rd32(E1000_STATUS) &
+ E1000_STATUS_GIO_MASTER_ENABLE))
+ break;
+ udelay(100);
+ timeout--;
+ }
+
+ if (!timeout) {
+ hw_dbg("Master requests are pending.\n");
+ ret_val = -E1000_ERR_MASTER_REQUESTS_PENDING;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_validate_mdi_setting - Verify MDI/MDIx settings
+ * @hw: pointer to the HW structure
+ *
+ * Verify that when not using auto-negotitation that MDI/MDIx is correctly
+ * set, which is forced to MDI mode only.
+ **/
+s32 igb_validate_mdi_setting(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+
+ /* All MDI settings are supported on 82580 and newer. */
+ if (hw->mac.type >= e1000_82580)
+ goto out;
+
+ if (!hw->mac.autoneg && (hw->phy.mdix == 0 || hw->phy.mdix == 3)) {
+ hw_dbg("Invalid MDI setting detected\n");
+ hw->phy.mdix = 1;
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_write_8bit_ctrl_reg - Write a 8bit CTRL register
+ * @hw: pointer to the HW structure
+ * @reg: 32bit register offset such as E1000_SCTL
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes an address/data control type register. There are several of these
+ * and they all have the format address << 8 | data and bit 31 is polled for
+ * completion.
+ **/
+s32 igb_write_8bit_ctrl_reg(struct e1000_hw *hw, u32 reg,
+ u32 offset, u8 data)
+{
+ u32 i, regvalue = 0;
+ s32 ret_val = 0;
+
+ /* Set up the address and data */
+ regvalue = ((u32)data) | (offset << E1000_GEN_CTL_ADDRESS_SHIFT);
+ wr32(reg, regvalue);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < E1000_GEN_POLL_TIMEOUT; i++) {
+ udelay(5);
+ regvalue = rd32(reg);
+ if (regvalue & E1000_GEN_CTL_READY)
+ break;
+ }
+ if (!(regvalue & E1000_GEN_CTL_READY)) {
+ hw_dbg("Reg %08x did not indicate ready\n", reg);
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_enable_mng_pass_thru - Enable processing of ARP's
+ * @hw: pointer to the HW structure
+ *
+ * Verifies the hardware needs to leave interface enabled so that frames can
+ * be directed to and from the management interface.
+ **/
+bool igb_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ u32 manc;
+ u32 fwsm, factps;
+ bool ret_val = false;
+
+ if (!hw->mac.asf_firmware_present)
+ goto out;
+
+ manc = rd32(E1000_MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN))
+ goto out;
+
+ if (hw->mac.arc_subsystem_valid) {
+ fwsm = rd32(E1000_FWSM);
+ factps = rd32(E1000_FACTPS);
+
+ if (!(factps & E1000_FACTPS_MNGCG) &&
+ ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT))) {
+ ret_val = true;
+ goto out;
+ }
+ } else {
+ if ((manc & E1000_MANC_SMBUS_EN) &&
+ !(manc & E1000_MANC_ASF_EN)) {
+ ret_val = true;
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}