1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/iio/adc/qcom,pm8018-adc.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm's PM8xxx voltage XOADC
maintainers:
- Linus Walleij <linus.walleij@linaro.org>
description: |
The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal
oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921.
properties:
compatible:
enum:
- qcom,pm8018-adc
- qcom,pm8038-adc
- qcom,pm8058-adc
- qcom,pm8921-adc
reg:
maxItems: 1
description:
ADC base address in the PMIC, typically 0x197.
xoadc-ref-supply:
description:
The reference voltage may vary with PMIC variant but is typically
something like 2.2 or 1.8V.
interrupts:
maxItems: 1
"#address-cells":
const: 2
description:
The first cell is the prescaler (on PM8058) or premux (on PM8921)
with two valid bits so legal values are 0x00, 0x01 or 0x02.
The second cell is the main analog mux setting (0x00..0x0f).
The combination of prescaler/premux and analog mux uniquely addresses
a hardware channel on all systems.
"#size-cells":
const: 0
"#io-channel-cells":
const: 2
description:
The cells are precaler or premux followed by the analog muxing line.
additionalProperties: false
required:
- compatible
- reg
- "#io-channel-cells"
- "#address-cells"
- "#size-cells"
- adc-channel@c
- adc-channel@d
- adc-channel@f
patternProperties:
"^(adc-channel@)[0-9a-f]$":
type: object
description: |
ADC channel specific configuration.
Note that channels c, d and f must be present for calibration.
These three nodes are used for absolute and ratiometric calibration
and only need to have these reg values: they are by hardware definition
1:1 ratio converters that sample 625, 1250 and 0 milliV and create
an interpolation calibration for all other ADCs.
properties:
reg:
maxItems: 1
qcom,decimation:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
This parameter is used to decrease the ADC sampling rate.
Quicker measurements can be made by reducing the decimation ratio.
Valid values are 512, 1024, 2048, 4096.
If the property is not found, a default value of 512 will be used.
qcom,ratiometric:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
Channel calibration type. If this property is specified
VADC will use a special voltage references for channel
calibration. The available references are specified in the
as a u32 value setting (see below) and it is compulsory
to also specify this reference if ratiometric calibration
is selected.
If the property is not found, the channel will be
calibrated with the 0.625V and 1.25V reference channels, also
known as an absolute calibration.
The reference voltage pairs when using ratiometric calibration:
0 = XO_IN/XOADC_GND
1 = PMIC_IN/XOADC_GND
2 = PMIC_IN/BMS_CSP
3 (invalid)
4 = XOADC_GND/XOADC_GND
5 = XOADC_VREF/XOADC_GND
additionalProperties: false
required:
- reg
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
pmic {
#address-cells = <1>;
#size-cells = <0>;
adc@197 {
compatible = "qcom,pm8058-adc";
reg = <0x197>;
interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
#address-cells = <2>;
#size-cells = <0>;
#io-channel-cells = <2>;
vcoin: adc-channel@0 {
reg = <0x00 0x00>;
};
vbat: adc-channel@1 {
reg = <0x00 0x01>;
};
dcin: adc-channel@2 {
reg = <0x00 0x02>;
};
ichg: adc-channel@3 {
reg = <0x00 0x03>;
};
vph_pwr: adc-channel@4 {
reg = <0x00 0x04>;
};
usb_vbus: adc-channel@a {
reg = <0x00 0x0a>;
};
die_temp: adc-channel@b {
reg = <0x00 0x0b>;
};
ref_625mv: adc-channel@c {
reg = <0x00 0x0c>;
};
ref_1250mv: adc-channel@d {
reg = <0x00 0x0d>;
};
ref_325mv: adc-channel@e {
reg = <0x00 0x0e>;
};
ref_muxoff: adc-channel@f {
reg = <0x00 0x0f>;
};
};
};
...
|
