1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
|
# SPDX-License-Identifier: GPL-2.0
# Copyright (C) 2021 Sebastian Reichel
%YAML 1.2
---
$id: http://devicetree.org/schemas/power/supply/bq25890.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Binding for bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger
maintainers:
- Sebastian Reichel <sre@kernel.org>
allOf:
- $ref: power-supply.yaml#
properties:
compatible:
enum:
- ti,bq25890
- ti,bq25892
- ti,bq25895
- ti,bq25896
reg:
maxItems: 1
interrupts:
maxItems: 1
ti,battery-regulation-voltage:
$ref: /schemas/types.yaml#/definitions/uint32
description: maximum charging voltage (in uV)
ti,charge-current:
$ref: /schemas/types.yaml#/definitions/uint32
description: maximum charging current (in uA)
ti,termination-current:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
charge will be terminated when current in constant-voltage phase
drops below this value (in uA)
ti,precharge-current:
$ref: /schemas/types.yaml#/definitions/uint32
description: maximum charge current during precharge phase (in uA)
ti,minimum-sys-voltage:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
when battery is charging and it is below minimum system voltage,
the system will be regulated above minimum-sys-voltage setting (in uV)
ti,boost-voltage:
$ref: /schemas/types.yaml#/definitions/uint32
description: VBUS voltage level in boost mode (in uV)
ti,boost-max-current:
$ref: /schemas/types.yaml#/definitions/uint32
description: maximum allowed current draw in boost mode (in uA)
ti,boost-low-freq:
description: boost mode frequency will be 500kHz, otherwise 1.5MHz
type: boolean
ti,use-ilim-pin:
description: |
ILIM resistor will be used and the input current will be the lower
between the resistor setting and the IINLIM register setting
type: boolean
ti,thermal-regulation-threshold:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
temperature above which the charge current is lowered, to avoid overheating
(in degrees Celsius). If omitted, the default setting will be used (120 degrees)
ti,ibatcomp-micro-ohms:
description: value of a resistor in series with the battery (in Micro Ohms)
ti,ibatcomp-clamp-microvolt:
description: max. charging voltage adjustment due to expected voltage drop on in-series resistor
required:
- compatible
- reg
- interrupts
- ti,battery-regulation-voltage
- ti,charge-current
- ti,termination-current
- ti,precharge-current
- ti,minimum-sys-voltage
- ti,boost-voltage
- ti,boost-max-current
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
i2c0 {
#address-cells = <1>;
#size-cells = <0>;
charger@6a {
compatible = "ti,bq25890";
reg = <0x6a>;
interrupt-parent = <&gpio1>;
interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
ti,battery-regulation-voltage = <4200000>;
ti,charge-current = <1000000>;
ti,termination-current = <50000>;
ti,precharge-current = <128000>;
ti,minimum-sys-voltage = <3600000>;
ti,boost-voltage = <5000000>;
ti,boost-max-current = <1000000>;
ti,use-ilim-pin;
ti,thermal-regulation-threshold = <120>;
};
};
|
