1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
|
# SPDX-License-Identifier: GPL-2.0-only
%YAML 1.2
---
$id: http://devicetree.org/schemas/soc/qcom/qcom,rpmh-rsc.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm RPMH RSC
maintainers:
- Bjorn Andersson <bjorn.andersson@linaro.org>
description: |
Resource Power Manager Hardened (RPMH) is the mechanism for communicating
with the hardened resource accelerators on Qualcomm SoCs. Requests to the
resources can be written to the Trigger Command Set (TCS) registers and
using a (addr, val) pair and triggered. Messages in the TCS are then sent in
sequence over an internal bus.
The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and
active/wake resource requests. Multiple such DRVs can exist in a SoC and can
be written to from Linux. The structure of each DRV follows the same template
with a few variations that are captured by the properties here.
A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
have powered off to facilitate idle power saving. TCS could be classified as::
ACTIVE - Triggered by Linux
SLEEP - Triggered by F/W
WAKE - Triggered by F/W
CONTROL - Triggered by F/W
See also:: <dt-bindings/soc/qcom,rpmh-rsc.h>
The order in which they are described in the DT, should match the hardware
configuration.
Requests can be made for the state of a resource, when the subsystem is
active or idle. When all subsystems like Modem, GPU, CPU are idle, the
resource state will be an aggregate of the sleep votes from each of those
subsystems. Clients may request a sleep value for their shared resources in
addition to the active mode requests.
Drivers that want to use the RSC to communicate with RPMH must specify their
bindings as child nodes of the RSC controllers they wish to communicate with.
properties:
compatible:
const: qcom,rpmh-rsc
interrupts:
minItems: 1
maxItems: 4
description:
The interrupt that trips when a message complete/response is received for
this DRV from the accelerators.
Number of interrupts must match number of DRV blocks.
label:
description:
Name for the RSC. The name would be used in trace logs.
qcom,drv-id:
$ref: /schemas/types.yaml#/definitions/uint32
description:
The ID of the DRV in the RSC block that will be used by this controller.
qcom,tcs-config:
$ref: /schemas/types.yaml#/definitions/uint32-matrix
minItems: 4
maxItems: 4
items:
items:
- description: |
TCS type::
- ACTIVE_TCS
- SLEEP_TCS
- WAKE_TCS
- CONTROL_TCS
enum: [ 0, 1, 2, 3 ]
- description: Number of TCS
description: |
The tuple defining the configuration of TCS. Must have two cells which
describe each TCS type. The order of the TCS must match the hardware
configuration.
qcom,tcs-offset:
$ref: /schemas/types.yaml#/definitions/uint32
description:
The offset of the TCS blocks.
reg:
minItems: 1
maxItems: 4
reg-names:
minItems: 1
items:
- const: drv-0
- const: drv-1
- const: drv-2
- const: drv-3
bcm-voter:
$ref: /schemas/interconnect/qcom,bcm-voter.yaml#
clock-controller:
$ref: /schemas/clock/qcom,rpmhcc.yaml#
power-controller:
$ref: /schemas/power/qcom,rpmpd.yaml#
patternProperties:
'-regulators$':
$ref: /schemas/regulator/qcom,rpmh-regulator.yaml#
required:
- compatible
- interrupts
- qcom,drv-id
- qcom,tcs-config
- qcom,tcs-offset
- reg
- reg-names
additionalProperties: false
examples:
- |
// For a TCS whose RSC base address is 0x179C0000 and is at a DRV id of
// 2, the register offsets for DRV2 start at 0D00, the register
// calculations are like this::
// DRV0: 0x179C0000
// DRV2: 0x179C0000 + 0x10000 = 0x179D0000
// DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000
// TCS-OFFSET: 0xD00
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
rsc@179c0000 {
compatible = "qcom,rpmh-rsc";
reg = <0x179c0000 0x10000>,
<0x179d0000 0x10000>,
<0x179e0000 0x10000>;
reg-names = "drv-0", "drv-1", "drv-2";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
label = "apps_rsc";
qcom,tcs-offset = <0xd00>;
qcom,drv-id = <2>;
qcom,tcs-config = <ACTIVE_TCS 2>,
<SLEEP_TCS 3>,
<WAKE_TCS 3>,
<CONTROL_TCS 1>;
};
- |
// For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
// register offsets for DRV0 start at 01C00, the register calculations are
// like this::
// DRV0: 0xAF20000
// TCS-OFFSET: 0x1C00
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
rsc@af20000 {
compatible = "qcom,rpmh-rsc";
reg = <0xaf20000 0x10000>;
reg-names = "drv-0";
interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
label = "disp_rsc";
qcom,tcs-offset = <0x1c00>;
qcom,drv-id = <0>;
qcom,tcs-config = <ACTIVE_TCS 0>,
<SLEEP_TCS 1>,
<WAKE_TCS 1>,
<CONTROL_TCS 0>;
};
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
rsc@18200000 {
compatible = "qcom,rpmh-rsc";
reg = <0x18200000 0x10000>,
<0x18210000 0x10000>,
<0x18220000 0x10000>;
reg-names = "drv-0", "drv-1", "drv-2";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
label = "apps_rsc";
qcom,tcs-offset = <0xd00>;
qcom,drv-id = <2>;
qcom,tcs-config = <ACTIVE_TCS 2>,
<SLEEP_TCS 3>,
<WAKE_TCS 3>,
<CONTROL_TCS 0>;
clock-controller {
compatible = "qcom,sm8350-rpmh-clk";
#clock-cells = <1>;
clock-names = "xo";
clocks = <&xo_board>;
};
power-controller {
compatible = "qcom,sm8350-rpmhpd";
#power-domain-cells = <1>;
operating-points-v2 = <&rpmhpd_opp_table>;
rpmhpd_opp_table: opp-table {
compatible = "operating-points-v2";
rpmhpd_opp_ret: opp1 {
opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
};
rpmhpd_opp_min_svs: opp2 {
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
};
rpmhpd_opp_low_svs: opp3 {
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
};
rpmhpd_opp_svs: opp4 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
};
rpmhpd_opp_svs_l1: opp5 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
};
rpmhpd_opp_nom: opp6 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
};
rpmhpd_opp_nom_l1: opp7 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
};
rpmhpd_opp_nom_l2: opp8 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
};
rpmhpd_opp_turbo: opp9 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
};
rpmhpd_opp_turbo_l1: opp10 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
};
};
};
bcm-voter {
compatible = "qcom,bcm-voter";
};
};
|
