1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
|
// SPDX-License-Identifier: GPL-2.0
/* Driver for the Texas Instruments DP83TD510 PHY
* Copyright (c) 2022 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
*/
#include <linux/bitfield.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
#define DP83TD510E_PHY_ID 0x20000181
/* MDIO_MMD_VEND2 registers */
#define DP83TD510E_PHY_STS 0x10
/* Bit 7 - mii_interrupt, active high. Clears on read.
* Note: Clearing does not necessarily deactivate IRQ pin if interrupts pending.
* This differs from the DP83TD510E datasheet (2020) which states this bit
* clears on write 0.
*/
#define DP83TD510E_STS_MII_INT BIT(7)
#define DP83TD510E_LINK_STATUS BIT(0)
#define DP83TD510E_GEN_CFG 0x11
#define DP83TD510E_GENCFG_INT_POLARITY BIT(3)
#define DP83TD510E_GENCFG_INT_EN BIT(1)
#define DP83TD510E_GENCFG_INT_OE BIT(0)
#define DP83TD510E_INTERRUPT_REG_1 0x12
#define DP83TD510E_INT1_LINK BIT(13)
#define DP83TD510E_INT1_LINK_EN BIT(5)
#define DP83TD510E_AN_STAT_1 0x60c
#define DP83TD510E_MASTER_SLAVE_RESOL_FAIL BIT(15)
#define DP83TD510E_MSE_DETECT 0xa85
#define DP83TD510_SQI_MAX 7
/* Register values are converted to SNR(dB) as suggested by
* "Application Report - DP83TD510E Cable Diagnostics Toolkit":
* SNR(dB) = -10 * log10 (VAL/2^17) - 1.76 dB.
* SQI ranges are implemented according to "OPEN ALLIANCE - Advanced diagnostic
* features for 100BASE-T1 automotive Ethernet PHYs"
*/
static const u16 dp83td510_mse_sqi_map[] = {
0x0569, /* < 18dB */
0x044c, /* 18dB =< SNR < 19dB */
0x0369, /* 19dB =< SNR < 20dB */
0x02b6, /* 20dB =< SNR < 21dB */
0x0227, /* 21dB =< SNR < 22dB */
0x01b6, /* 22dB =< SNR < 23dB */
0x015b, /* 23dB =< SNR < 24dB */
0x0000 /* 24dB =< SNR */
};
static int dp83td510_config_intr(struct phy_device *phydev)
{
int ret;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
DP83TD510E_INTERRUPT_REG_1,
DP83TD510E_INT1_LINK_EN);
if (ret)
return ret;
ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2,
DP83TD510E_GEN_CFG,
DP83TD510E_GENCFG_INT_POLARITY |
DP83TD510E_GENCFG_INT_EN |
DP83TD510E_GENCFG_INT_OE);
} else {
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
DP83TD510E_INTERRUPT_REG_1, 0x0);
if (ret)
return ret;
ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2,
DP83TD510E_GEN_CFG,
DP83TD510E_GENCFG_INT_EN);
if (ret)
return ret;
}
return ret;
}
static irqreturn_t dp83td510_handle_interrupt(struct phy_device *phydev)
{
int ret;
/* Read the current enabled interrupts */
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_INTERRUPT_REG_1);
if (ret < 0) {
phy_error(phydev);
return IRQ_NONE;
} else if (!(ret & DP83TD510E_INT1_LINK_EN) ||
!(ret & DP83TD510E_INT1_LINK)) {
return IRQ_NONE;
}
phy_trigger_machine(phydev);
return IRQ_HANDLED;
}
static int dp83td510_read_status(struct phy_device *phydev)
{
u16 phy_sts;
int ret;
phydev->speed = SPEED_UNKNOWN;
phydev->duplex = DUPLEX_UNKNOWN;
phydev->pause = 0;
phydev->asym_pause = 0;
linkmode_zero(phydev->lp_advertising);
phy_sts = phy_read(phydev, DP83TD510E_PHY_STS);
phydev->link = !!(phy_sts & DP83TD510E_LINK_STATUS);
if (phydev->link) {
/* This PHY supports only one link mode: 10BaseT1L_Full */
phydev->duplex = DUPLEX_FULL;
phydev->speed = SPEED_10;
if (phydev->autoneg == AUTONEG_ENABLE) {
ret = genphy_c45_read_lpa(phydev);
if (ret)
return ret;
phy_resolve_aneg_linkmode(phydev);
}
}
if (phydev->autoneg == AUTONEG_ENABLE) {
ret = genphy_c45_baset1_read_status(phydev);
if (ret < 0)
return ret;
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
DP83TD510E_AN_STAT_1);
if (ret < 0)
return ret;
if (ret & DP83TD510E_MASTER_SLAVE_RESOL_FAIL)
phydev->master_slave_state = MASTER_SLAVE_STATE_ERR;
} else {
return genphy_c45_pma_baset1_read_master_slave(phydev);
}
return 0;
}
static int dp83td510_config_aneg(struct phy_device *phydev)
{
bool changed = false;
int ret;
ret = genphy_c45_pma_baset1_setup_master_slave(phydev);
if (ret < 0)
return ret;
if (phydev->autoneg == AUTONEG_DISABLE)
return genphy_c45_an_disable_aneg(phydev);
ret = genphy_c45_an_config_aneg(phydev);
if (ret < 0)
return ret;
if (ret > 0)
changed = true;
return genphy_c45_check_and_restart_aneg(phydev, changed);
}
static int dp83td510_get_sqi(struct phy_device *phydev)
{
int sqi, ret;
u16 mse_val;
if (!phydev->link)
return 0;
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_MSE_DETECT);
if (ret < 0)
return ret;
mse_val = 0xFFFF & ret;
for (sqi = 0; sqi < ARRAY_SIZE(dp83td510_mse_sqi_map); sqi++) {
if (mse_val >= dp83td510_mse_sqi_map[sqi])
return sqi;
}
return -EINVAL;
}
static int dp83td510_get_sqi_max(struct phy_device *phydev)
{
return DP83TD510_SQI_MAX;
}
static int dp83td510_get_features(struct phy_device *phydev)
{
/* This PHY can't respond on MDIO bus if no RMII clock is enabled.
* In case RMII mode is used (most meaningful mode for this PHY) and
* the PHY do not have own XTAL, and CLK providing MAC is not probed,
* we won't be able to read all needed ability registers.
* So provide it manually.
*/
linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->supported);
linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->supported);
linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
phydev->supported);
return 0;
}
static struct phy_driver dp83td510_driver[] = {
{
PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID),
.name = "TI DP83TD510E",
.config_aneg = dp83td510_config_aneg,
.read_status = dp83td510_read_status,
.get_features = dp83td510_get_features,
.config_intr = dp83td510_config_intr,
.handle_interrupt = dp83td510_handle_interrupt,
.get_sqi = dp83td510_get_sqi,
.get_sqi_max = dp83td510_get_sqi_max,
.suspend = genphy_suspend,
.resume = genphy_resume,
} };
module_phy_driver(dp83td510_driver);
static struct mdio_device_id __maybe_unused dp83td510_tbl[] = {
{ PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID) },
{ }
};
MODULE_DEVICE_TABLE(mdio, dp83td510_tbl);
MODULE_DESCRIPTION("Texas Instruments DP83TD510E PHY driver");
MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
MODULE_LICENSE("GPL v2");
|
