Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

10 files changed, 412 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt
new file mode 100644
index 000000000..624bd76f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt
@@ -0,0 +1,21 @@
+FAIRCHILD SEMICONDUCTOR FSA9480 MICROUSB SWITCH
+
+The FSA9480 is a USB port accessory detector and switch. The FSA9480 is fully
+controlled using I2C and enables USB data, stereo and mono audio, video,
+microphone, and UART data to use a common connector port.
+
+Required properties:
+ - compatible : Must be one of
+   "fcs,fsa9480"
+   "fcs,fsa880"
+ - reg : Specifies i2c slave address. Must be 0x25.
+ - interrupts : Should contain one entry specifying interrupt signal of
+   interrupt parent to which interrupt pin of the chip is connected.
+
+ Example:
+	musb@25 {
+		compatible = "fcs,fsa9480";
+		reg = <0x25>;
+		interrupt-parent = <&gph2>;
+		interrupts = <7 0>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-max3355.txt b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
new file mode 100644
index 000000000..f2288ea9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
@@ -0,0 +1,21 @@
+Maxim Integrated MAX3355 USB OTG chip
+-------------------------------------
+
+MAX3355 integrates a charge pump and comparators to enable a system with an
+integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
+device.
+
+Required properties:
+- compatible: should be "maxim,max3355";
+- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+		    connected to the MAX3355's SHDN# pin;
+- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+	    connected to the MAX3355's ID_OUT pin.
+
+Example:
+
+	usb-otg {
+		compatible = "maxim,max3355";
+		maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-palmas.txt b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt
new file mode 100644
index 000000000..f61d5af44
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt
@@ -0,0 +1,22 @@
+EXTCON FOR PALMAS/TWL CHIPS
+
+PALMAS USB COMPARATOR
+Required Properties:
+ - compatible: should contain one of:
+   * "ti,palmas-usb-vid".
+   * "ti,twl6035-usb-vid".
+   * "ti,palmas-usb" (DEPRECATED - use "ti,palmas-usb-vid").
+   * "ti,twl6035-usb" (DEPRECATED - use "ti,twl6035-usb-vid").
+
+Optional Properties:
+ - ti,wakeup : To enable the wakeup comparator in probe
+ - ti,enable-id-detection: Perform ID detection. If id-gpio is specified
+		it performs id-detection using GPIO else using OTG core.
+ - ti,enable-vbus-detection: Perform VBUS detection.
+ - id-gpio: gpio for GPIO ID detection. See gpio binding.
+ - debounce-delay-ms: debounce delay for GPIO ID pin in milliseconds.
+
+palmas-usb {
+       compatible = "ti,twl6035-usb", "ti,palmas-usb";
+       ti,wakeup;
+};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
new file mode 100644
index 000000000..4b0f41448
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PTN5150 CC (Configuration Channel) Logic device
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  PTN5150 is a small thin low power CC logic chip supporting the USB Type-C
+  connector application with CC control logic detection and indication
+  functions.  It is interfaced to the host controller using an I2C interface.
+
+properties:
+  compatible:
+    const: nxp,ptn5150
+
+  int-gpios:
+    deprecated: true
+    description:
+      GPIO pin (input) connected to the PTN5150's INTB pin.
+      Use "interrupts" instead.
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  vbus-gpios:
+    description:
+      GPIO pin (output) used to control VBUS. If skipped, no such control
+      takes place.
+
+required:
+  - compatible
+  - interrupts
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ptn5150@1d {
+            compatible = "nxp,ptn5150";
+            reg = <0x1d>;
+            interrupt-parent = <&msmgpio>;
+            interrupts = <78 IRQ_TYPE_LEVEL_HIGH>;
+            vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt
new file mode 100644
index 000000000..cfcf455ad
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt
@@ -0,0 +1,23 @@
+
+* Richtek RT8973A - Micro USB Switch device
+
+The Richtek RT8973A is Micro USB Switch with OVP and I2C interface. The RT8973A
+is a USB port accessory detector and switch that is optimized to protect low
+voltage system from abnormal high input voltage (up to 28V) and supports high
+speed USB operation. Also, RT8973A support 'auto-configuration' mode.
+If auto-configuration mode is enabled, RT8973A would control internal h/w patch
+for USB D-/D+ switching.
+
+Required properties:
+- compatible: Should be "richtek,rt8973a-muic"
+- reg: Specifies the I2C slave address of the MUIC block. It should be 0x14
+- interrupts: Interrupt specifiers for detection interrupt sources.
+
+Example:
+
+	rt8973a@14 {
+		compatible = "richtek,rt8973a-muic";
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 0>;
+		reg = <0x14>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt
new file mode 100644
index 000000000..fc3888e09
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt
@@ -0,0 +1,21 @@
+
+* SM5502 MUIC (Micro-USB Interface Controller) device
+
+The Silicon Mitus SM5502 is a MUIC (Micro-USB Interface Controller) device
+which can detect the state of external accessory when external accessory is
+attached or detached and button is pressed or released. It is interfaced to
+the host controller using an I2C interface.
+
+Required properties:
+- compatible: Should be "siliconmitus,sm5502-muic"
+- reg: Specifies the I2C slave address of the MUIC block. It should be 0x25
+- interrupts: Interrupt specifiers for detection interrupt sources.
+
+Example:
+
+	sm5502@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 0>;
+		reg = <0x25>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
new file mode 100644
index 000000000..dfc14f71e
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
@@ -0,0 +1,21 @@
+USB GPIO Extcon device
+
+This is a virtual device used to generate USB cable states from the USB ID pin
+connected to a GPIO pin.
+
+Required properties:
+- compatible: Should be "linux,extcon-usb-gpio"
+
+Either one of id-gpio or vbus-gpio must be present. Both can be present as well.
+- id-gpio: gpio for USB ID pin. See gpio binding.
+- vbus-gpio: gpio for USB VBUS pin.
+
+Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below:
+	extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+	}
+
+	&omap_dwc3_1 {
+		extcon = <&extcon_usb1>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml
new file mode 100644
index 000000000..20e1ccfc8
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-usbc-cros-ec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ChromeOS EC USB Type-C cable and accessories detection
+
+maintainers:
+  - Benson Leung <bleung@chromium.org>
+  - Enric Balletbo i Serra <enric.balletbo@collabora.com>
+
+description: |
+  On ChromeOS systems with USB Type C ports, the ChromeOS Embedded Controller is
+  able to detect the state of external accessories such as display adapters
+  or USB devices when said accessories are attached or detached.
+  The node for this device must be under a cros-ec node like google,cros-ec-spi
+  or google,cros-ec-i2c.
+
+properties:
+  compatible:
+    const: google,extcon-usbc-cros-ec
+
+  google,usb-port-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: the port id
+    minimum: 0
+    maximum: 255
+
+required:
+  - compatible
+  - google,usb-port-id
+
+additionalProperties: false
+
+examples:
+  - |
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        cros-ec@0 {
+            compatible = "google,cros-ec-spi";
+            reg = <0>;
+
+            usbc_extcon0: extcon0 {
+                compatible = "google,extcon-usbc-cros-ec";
+                google,usb-port-id = <0>;
+            };
+
+            usbc_extcon1: extcon1 {
+                compatible = "google,extcon-usbc-cros-ec";
+                google,usb-port-id = <1>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
new file mode 100644
index 000000000..35383adb1
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
@@ -0,0 +1,41 @@
+Qualcomm's PM8941 USB ID Extcon device
+
+Some Qualcomm PMICs have a "misc" module that can be used to detect when
+the USB ID pin has been pulled low or high.
+
+PROPERTIES
+
+- compatible:
+    Usage: required
+    Value type: <string>
+    Definition: Should contain "qcom,pm8941-misc";
+
+- reg:
+    Usage: required
+    Value type: <u32>
+    Definition: Should contain the offset to the misc address space
+
+- interrupts:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: Should contain the usb id interrupt
+
+- interrupt-names:
+    Usage: required
+    Value type: <stringlist>
+    Definition: Should contain the string "usb_id" for the usb id interrupt
+
+Example:
+
+	pmic {
+		usb_id: misc@900 {
+			compatible = "qcom,pm8941-misc";
+			reg = <0x900>;
+			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "usb_id";
+		};
+	}
+
+	usb-controller {
+		extcon = <&usb_id>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml b/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml
new file mode 100644
index 000000000..5fe784f48
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/wlf,arizona.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  These devices are audio SoCs with extensive digital capabilities and a
+  range of analogue I/O.
+
+  This document lists Extcon specific bindings, see the primary binding
+  document ../mfd/arizona.yaml
+
+properties:
+  wlf,hpdet-channel:
+    description:
+      Headphone detection channel.  ARIZONA_ACCDET_MODE_HPL/1 sets the
+      headphone detect mode to HPDETL, ARIZONA_ACCDET_MODE_HPR/2 sets it
+      to HPDETR.  If this node is not included or if the value is unknown,
+      then headphone detection mode is set to HPDETL.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 1
+    maximum: 2
+
+  wlf,use-jd2:
+    description:
+      Use the additional JD input along with JD1 for dual pin jack detection.
+    type: boolean
+
+  wlf,use-jd2-nopull:
+    description:
+      Internal pull on JD2 is disabled when used for jack detection.
+    type: boolean
+
+  wlf,jd-invert:
+    description:
+      Invert the polarity of the jack detection switch.
+    type: boolean
+
+  wlf,micd-software-compare:
+    description:
+      Use a software comparison to determine mic presence.
+    type: boolean
+
+  wlf,micd-detect-debounce:
+    description:
+      Additional software microphone detection debounce specified in
+      milliseconds.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  wlf,micd-pol-gpio:
+    description:
+      GPIO specifier for the GPIO controlling the headset polarity if one
+      exists.
+    maxItems: 1
+
+  wlf,micd-bias-start-time:
+    description:
+      Time allowed for MICBIAS to startup prior to performing microphone
+      detection, specified as per the ARIZONA_MICD_TIME_XXX defines.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 12
+
+  wlf,micd-rate:
+    description:
+      Delay between successive microphone detection measurements, specified
+      as per the ARIZONA_MICD_TIME_XXX defines.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 12
+
+  wlf,micd-dbtime:
+    description:
+      Microphone detection hardware debounces specified as the number of
+      measurements to take.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum: [2, 4]
+
+  wlf,micd-timeout-ms:
+    description:
+      Timeout for microphone detection, specified in milliseconds.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  wlf,micd-force-micbias:
+    description:
+      Force MICBIAS continuously on during microphone detection.
+    type: boolean
+
+  wlf,micd-configs:
+    description:
+      Headset polarity configurations (generally used for detection of
+      CTIA / OMTP headsets), the field can be of variable length but
+      should always be a multiple of 3 cells long, each three cell group
+      represents one polarity configuration.
+    $ref: "/schemas/types.yaml#/definitions/uint32-matrix"
+    items:
+      items:
+        - description:
+            The first cell defines the accessory detection pin, zero
+            will use MICDET1 and 0x2000 will use MICDET2.
+          enum: [ 0, 0x2000 ]
+        - description:
+            The second cell represents the MICBIAS to be used. Zero
+            will use MICVDD, 1-3 will use MICBIASx.
+          minimum: 0
+          maximum: 3
+        - description:
+            The third cell represents the value of the micd-pol-gpio
+            pin.
+          minimum: 0
+          maximum: 1
+
+  wlf,gpsw:
+    description:
+      Settings for the general purpose switch, set as one of the
+      ARIZONA_GPSW_XXX defines.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 3
+
+additionalProperties: true