Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 199 insertions, 0 deletions

diff --git a/Documentation/hwmon/w83792d.rst b/Documentation/hwmon/w83792d.rst
new file mode 100644
index 000000000..92c4bfe49
--- /dev/null
+++ b/Documentation/hwmon/w83792d.rst
@@ -0,0 +1,199 @@
+Kernel driver w83792d
+=====================
+
+Supported chips:
+
+  * Winbond W83792D
+
+    Prefix: 'w83792d'
+
+    Addresses scanned: I2C 0x2c - 0x2f
+
+    Datasheet: http://www.winbond.com.tw
+
+Author: Shane Huang (Winbond)
+Updated: Roger Lucas
+
+
+Module Parameters
+-----------------
+
+* init int
+    (default 1)
+
+    Use 'init=0' to bypass initializing the chip.
+    Try this if your computer crashes when you load the module.
+
+* force_subclients=bus,caddr,saddr,saddr
+    This is used to force the i2c addresses for subclients of
+    a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b`
+    to force the subclients of chip 0x2f on bus 0 to i2c addresses
+    0x4a and 0x4b.
+
+
+Description
+-----------
+
+This driver implements support for the Winbond W83792AD/D.
+
+Detection of the chip can sometimes be foiled because it can be in an
+internal state that allows no clean access (Bank with ID register is not
+currently selected). If you know the address of the chip, use a 'force'
+parameter; this will put it into a more well-behaved state first.
+
+The driver implements three temperature sensors, seven fan rotation speed
+sensors, nine voltage sensors, and two automatic fan regulation
+strategies called: Smart Fan I (Thermal Cruise mode) and Smart Fan II.
+
+The driver also implements up to seven fan control outputs: pwm1-7.  Pwm1-7
+can be configured to PWM output or Analogue DC output via their associated
+pwmX_mode. Outputs pwm4 through pwm7 may or may not be present depending on
+how the W83792AD/D was configured by the BIOS.
+
+Automatic fan control mode is possible only for fan1-fan3.
+
+For all pwmX outputs, a value of 0 means minimum fan speed and a value of
+255 means maximum fan speed.
+
+Temperatures are measured in degrees Celsius and measurement resolution is 1
+degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
+the temperature gets higher than the Overtemperature Shutdown value; it stays
+on until the temperature falls below the Hysteresis value.
+
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. Fan
+readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or
+128) to give the readings more range or accuracy.
+
+Voltage sensors (also known as IN sensors) report their values in millivolts.
+An alarm is triggered if the voltage has crossed a programmable minimum
+or maximum limit.
+
+Alarms are provided as output from "realtime status register". Following bits
+are defined:
+
+==== ==========
+bit   alarm on
+==== ==========
+0    in0
+1    in1
+2    temp1
+3    temp2
+4    temp3
+5    fan1
+6    fan2
+7    fan3
+8    in2
+9    in3
+10   in4
+11   in5
+12   in6
+13   VID change
+14   chassis
+15   fan7
+16   tart1
+17   tart2
+18   tart3
+19   in7
+20   in8
+21   fan4
+22   fan5
+23   fan6
+==== ==========
+
+Tart will be asserted while target temperature cannot be achieved after 3 minutes
+of full speed rotation of corresponding fan.
+
+In addition to the alarms described above, there is a CHAS alarm on the chips
+which triggers if your computer case is open (This one is latched, contrary
+to realtime alarms).
+
+The chips only update values each 3 seconds; reading them more often will
+do no harm, but will return 'old' values.
+
+
+W83792D PROBLEMS
+----------------
+Known problems:
+	- This driver is only for Winbond W83792D C version device, there
+	  are also some motherboards with B version W83792D device. The
+	  calculation method to in6-in7(measured value, limits) is a little
+	  different between C and B version. C or B version can be identified
+	  by CR[0x49h].
+	- The function of vid and vrm has not been finished, because I'm NOT
+	  very familiar with them. Adding support is welcome.
+	- The function of chassis open detection needs more tests.
+	- If you have ASUS server board and chip was not found: Then you will
+	  need to upgrade to latest (or beta) BIOS. If it does not help please
+	  contact us.
+
+Fan control
+-----------
+
+Manual mode
+-----------
+
+Works as expected. You just need to specify desired PWM/DC value (fan speed)
+in appropriate pwm# file.
+
+Thermal cruise
+--------------
+
+In this mode, W83792D provides the Smart Fan system to automatically control
+fan speed to keep the temperatures of CPU and the system within specific
+range. At first a wanted temperature and interval must be set. This is done
+via thermal_cruise# file. The tolerance# file serves to create T +- tolerance
+interval. The fan speed will be lowered as long as the current temperature
+remains below the thermal_cruise# +- tolerance# value. Once the temperature
+exceeds the high limit (T+tolerance), the fan will be turned on with a
+specific speed set by pwm# and automatically controlled its PWM duty cycle
+with the temperature varying. Three conditions may occur:
+
+(1) If the temperature still exceeds the high limit, PWM duty
+cycle will increase slowly.
+
+(2) If the temperature goes below the high limit, but still above the low
+limit (T-tolerance), the fan speed will be fixed at the current speed because
+the temperature is in the target range.
+
+(3) If the temperature goes below the low limit, PWM duty cycle will decrease
+slowly to 0 or a preset stop value until the temperature exceeds the low
+limit. (The preset stop value handling is not yet implemented in driver)
+
+Smart Fan II
+------------
+
+W83792D also provides a special mode for fan. Four temperature points are
+available. When related temperature sensors detects the temperature in preset
+temperature region (sf2_point@_fan# +- tolerance#) it will cause fans to run
+on programmed value from sf2_level@_fan#. You need to set four temperatures
+for each fan.
+
+
+/sys files
+----------
+
+pwm[1-7]
+	- this file stores PWM duty cycle or DC value (fan speed) in range:
+
+	    0 (stop) to 255 (full)
+pwm[1-3]_enable
+	- this file controls mode of fan/temperature control:
+
+	    * 0 Disabled
+	    * 1 Manual mode
+	    * 2 Smart Fan II
+	    * 3 Thermal Cruise
+pwm[1-7]_mode
+	- Select PWM or DC mode
+
+	    * 0 DC
+	    * 1 PWM
+thermal_cruise[1-3]
+	- Selects the desired temperature for cruise (degC)
+tolerance[1-3]
+	- Value in degrees of Celsius (degC) for +- T
+sf2_point[1-4]_fan[1-3]
+	- four temperature points for each fan for Smart Fan II
+sf2_level[1-3]_fan[1-3]
+	- three PWM/DC levels for each fan for Smart Fan II