Adding upstream version 5.10.209.upstream/5.10.209

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 464 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
new file mode 100644
index 000000000..d8326a5c6
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -0,0 +1,464 @@
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Cubietech Cubietruck Plus";
+	compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "cubietruck-plus:blue:usr";
+			gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
+		};
+
+		orange {
+			label = "cubietruck-plus:orange:usr";
+			gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */
+		};
+
+		white {
+			label = "cubietruck-plus:white:usr";
+			gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */
+		};
+
+		green {
+			label = "cubietruck-plus:green:usr";
+			gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
+		};
+	};
+
+	usb-hub {
+		/* I2C is not connected */
+		compatible = "smsc,usb3503";
+		initial-mode = <1>; /* initialize in HUB mode */
+		disabled-ports = <1>;
+		intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
+		connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+		refclk-frequency = <19200000>;
+	};
+
+	reg_usb1_vbus: reg-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
+	};
+
+	reg_usb2_vbus: reg-usb2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "On-board SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "ext_clock";
+		/* The WiFi low power clock must be 32768 Hz */
+		assigned-clocks = <&ac100_rtc 1>;
+		assigned-clock-rates = <32768>;
+		/* enables internal regulator and de-asserts reset */
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu100 {
+	cpu-supply = <&reg_dcdc3>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	/* GL830 USB-to-SATA bridge here */
+	status = "okay";
+};
+
+&ehci1 {
+	/* USB3503 HSIC USB 2.0 hub here */
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_dldo4>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mdio {
+	rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_sw>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp81x: pmic@3a3 {
+		compatible = "x-powers,axp818", "x-powers,axp813";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		swin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
+	};
+
+	ac100: codec@e89 {
+		compatible = "x-powers,ac100";
+		reg = <0xe89>;
+
+		ac100_codec: codec {
+			compatible = "x-powers,ac100-codec";
+			interrupt-parent = <&r_pio>;
+			interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+			#clock-cells = <0>;
+			clock-output-names = "4M_adda";
+		};
+
+		ac100_rtc: rtc {
+			compatible = "x-powers,ac100-rtc";
+			interrupt-parent = <&r_intc>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&ac100_codec>;
+			#clock-cells = <1>;
+			clock-output-names = "cko1_rtc",
+					     "cko2_rtc",
+					     "cko3_rtc";
+		};
+	};
+};
+
+#include "axp81x.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1v8";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dram-pll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+	/*
+	 * The schematics say this should be 3.3V, but the FEX file says
+	 * it should be 3V. The latter makes sense, as the WiFi module's
+	 * I/O is indirectly powered from DCDC1, through SW. It is rated
+	 * at 2.98V maximum.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <900000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "dp-pwr";
+};
+
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "ephy-io";
+};
+
+&reg_dldo4 {
+	/*
+	 * The PHY requires 20ms after all voltages are applied until core
+	 * logic is ready and 30ms after the reset pin is de-asserted.
+	 * Set a 100ms delay to account for PMIC ramp time and board traces.
+	 */
+	regulator-enable-ramp-delay = <100000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "ephy";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "dp-bridge-1";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "dp-bridge-2";
+};
+
+&reg_fldo1 {
+	/* TODO should be handled by USB PHY */
+	regulator-always-on;
+	regulator-min-microvolt = <1080000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+	/*
+	 * Despite the embedded CPUs core not being used in any way,
+	 * this must remain on or the system will hang.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&reg_sw {
+	regulator-name = "vcc-wifi-io";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_dcdc1>;
+		vddio-supply = <&reg_sw>;
+		device-wakeup-gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+		host-wakeup-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		shutdown-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};